[App_rpt-users] ctcss Encode Issues
Steve Mahler
kizzy at lusfiber.net
Wed Aug 9 16:21:46 UTC 2017
Neil:
Understood. As long as you are thinking about a code change ... should
the PL tone be held thru the tailmessage system too?
...STeve
On 8/9/2017 11:15 AM, Michael "Lee" Lockwood wrote:
> Steve Mahler: The RX ctcss tones I'm using are being decoded by the
> dsp. I get verification of that when running debug in app_rpt.
>
> Neil: I'd like to have the same ctcss tone transmitted for the
> "repeater tail" and courtesy tone the same amount of time it's set in
> the rpt.conf file. I think I have mine set to 1.5 seconds.
>
> On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it at cac.net
> <mailto:k8it at cac.net>> wrote:
>
> for how long after a giben ctcss tone is reciebed do you want to
> use the same ctcss tx tone
> when would it reset to the 151.4 tone
> Thanks
> 73 Neil Sablatzky K8IT
> Allstar Node 41838 KITLINK
> Allstar Node 42087 KITLINK HUB
> IRLP Node exp0068
> Echolink K8IT-L
> WIRES-X K8IT 11479 Room 21479
>
> *From:* Michael "Lee" Lockwood <mailto:michael at lockwood.us.com>
> *Sent:* Wednesday, August 09, 2017 11:12 AM
> *To:* app_rpt-users at lists.allstarlink.org
> <mailto:app_rpt-users at lists.allstarlink.org>
> *Subject:* Re: [App_rpt-users] ctcss Encode Issues
>
> A follow up to my previous email:
>
> I have multiple ctcss tone frequencies in usbradio.conf. app_rpt
> is decoding the incoming CTCSS (confirmed using debug), and it
> transmits CTCSS while someone is actively keying the repeater.
> However, as soon as they release PTT, app_rpt stops transmitting
> the corresponding CTCSS tone that was being used, and reverts to
> the default tone instead.
>
> So, if I key the repeater using 146.2, it broadcasts out using
> 146.2 and other radios hear audio just fine. But, as soon as I
> release PTT on the mobile/portable radio, the squelch tail is
> broadcast using 151.4, not 146.2. This results in the users
> programmed with 146.2 not hearing the courtesy tone or squelch tail.
>
> Has anyone else run in to this issue?
>
> Here's my usbradio.conf file again:
>
> [usb]
>
> hdwtype=0
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=151.4
> rxctcssfreqs=146.2,141.3,151.4
> txctcssfreqs=146.2,141.3,151.4
> ;rxctcssoverride=0
> carrierfrom=usb
> ctcssfrom=dsp
> rxdemod=flat
> txprelim=yes
> txlimonly=no
> txtoctype=phase
> txmixa=composite
> txmixb=0
> invertptt=0
> duplex=1
> rxondelay=0
> rxnoisefiltype=0
> eeprom=0
>
>
>
> On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood
> <michael at lockwood.us.com <mailto:michael at lockwood.us.com>> wrote:
>
> Hello,
> I am unable to get any ctcss to be encoded during transmit,
> except for the tone frequency that's entered in to the
> txctcssdetault field. If I change that tone, the new value
> gets transmitted. However, all of the other tones in the
> txctcssfreqs are being ignored. However, I do know that the
> rxctcssfreqs values are being decoded. If I transmit in to
> the repeater using a tone not listed, or without a tone,
> app_rpt ignores it and does not repeat and key up the
> transmitter. Any assistance is greatly appreciated. Thanks
> in advance!
>
> Here's what's in my usbradio.conf
>
> [usb]
>
> hdwtype=0
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=151.4
> rxctcssfreqs=146.2,141.3,151.4
> txctcssfreqs=146.2,141.3,151.4
> ;rxctcssoverride=0
> carrierfrom=usb
> ctcssfrom=dsp
> rxdemod=flat
> txprelim=yes
> txlimonly=no
> txtoctype=phase
> txmixa=composite
> txmixb=0
> invertptt=0
> duplex=1
> rxondelay=0
> rxnoisefiltype=0
> eeprom=0
>
>
> --
>
> *Michael "Lee" Lockwood*
> michael at lockwood.us.com <mailto:michael at lockwood.us.com>
>
>
>
>
> --
>
> *Michael "Lee" Lockwood*
> michael at lockwood.us.com <mailto:michael at lockwood.us.com>
>
> ------------------------------------------------------------------------
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> <mailto:App_rpt-users at lists.allstarlink.org>
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
>
> To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
> and scroll down to the bottom of the page. Enter your email
> address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a
> message to the list detailing the problem.
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> <mailto:App_rpt-users at lists.allstarlink.org>
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
>
> To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
> and scroll down to the bottom of the page. Enter your email
> address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a
> message to the list detailing the problem.
>
>
>
>
> --
>
> *Michael "Lee" Lockwood*
> michael at lockwood.us.com <mailto:michael at lockwood.us.com>
>
> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
> Virus-free. www.avg.com
> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
>
>
> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20170809/18e8d713/attachment.html>
More information about the App_rpt-users
mailing list