[App_rpt-users] Temporary stop, then restart asterisk

[Bob]

Actually, just turn the repeater off, then later back on. Will test this. I
see I don't have it in rpt.conf.

 

Also, how do I tell which version of DIAL I have installed?

 

Thanks,

Bob

 

  _____  

From: App_rpt-users [mailto:app_rpt-users-bounces at lists.allstarlink.org] On
Behalf Of Bryan D. Boyle
Sent: Friday, May 26, 2017 10:03 AM
To: Users of Asterisk app_rpt
Subject: Re: [App_rpt-users] Temporary stop, then restart asterisk

 

cop 2 system enable

cop 3 system disable

--

Bryan

Sent from my iPhone 6S...No electrons were harmed in the sending of this
message.

 

 


On May 26, 2017, at 11:57, Mike - W5JR <w5jr.lists at gmail.com> wrote:

Do want to stop AllStar/Asterisk or just turn the repeater off? There is a
COP command for the latter. I'm not in front of a terminal to get you the
command. 

tnx
Mike / W5JR
Alpharetta GA




On May 26, 2017, at 11:46 AM, Bob Pyke <k6ecm1 at gmail.com> wrote:

 

Hmmm... sounds like an update is in order :-)

 

Thanks much,

Bob

 

Sent from my iPhone

 

On May 26, 2017, at 8:41 AM, Steve Zingman <szingman at msgstor.com> wrote:

 

OK,

/etc/init.d/asterisk stop <--- Stop asterisk

killall -9 asterisk <---------------- Make sure it's dead

ps ax | grep asterisk <--- Check to see if it's really dead

 

/etc/init.d/asterisk start <--- start asterisk

ps ax | grep asterisk <--- Check to see if it's really started

 

The newer release candidate fixes this.

 

73, Steve N4IRS

 

 

On 5/26/2017 11:37 AM, Bob Pyke wrote:

No. It will be off for several minutes, but I want it to stop when
commanded, and start on command. We are conducting an exercise. I don't know
the version, and logging into the node does not say. We've been operating,
pretty much since the introduction of app_rpt on the RPi

 

Thanks

 

Sent from my iPhone

 

On May 26, 2017, at 8:31 AM, Steve Zingman <szingman at msgstor.com> wrote:

 

Bob,

Are you talking about "bouncing" asterisk? A stop followed by a rapid start?
Which distribution and version are you running?

 

73, Steve N4IRS

 

On 5/26/2017 11:28 AM, Bob Pyke wrote:

I have a need to temporarily disable the repeater, then enable it. Timing is
critical, so a delay is undesirable. What is the best way to accomplish
this? I will be logged into the node.

 

Thanks,

Bob

Sent from my iPhone

_______________________________________________

App_rpt-users mailing list

App_rpt-users at lists.allstarlink.org

http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

 

To unsubscribe from this list please visit
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
scroll down to the bottom of the page. Enter your email address and press
the "Unsubscribe or edit options button"

You do not need a password to unsubscribe, you can do it via email
confirmation. If y

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20170526/e0fc631f/attachment.html>