[App_rpt-users] hub to simpleusb

[Mike]

-rpt.conf

rxchannel = SimpleUSB/usb_29999


-SimpleUSB.conf    ***- your config here is dependent to your cor/ptt 
method, this one is with parallel port, and your specific audio methods.


[usb_29999]
pp5=ptt
pp10=cor

eeprom = 0              ; EEPROM installed: 0,1
                         ; 0 = no (default)
                         ; 1 = yes

hdwtype = 0             ; Leave this set to 0 for USB sound fobs 
modified using
                       ; the instructions from usbfob.pdf. Use a setting of
                      ; 1 is for Dingotel/Sph interfaces.

duplex = 1              ; Duplex / 0 - half duplex /  1 - full duplex

; Receiver parameters

;carrierfrom=no
;carrierfrom=dsp
;carrierfrom=pp
carrierfrom=ppinvert
;carrierfrom=usb
;carrierfrom=usbinvert
;carrierfrom=vox

;  Tone & CTCSS

;ctcssfrom=no
ctcssfrom=dsp
;ctcssfrom=usb
;ctcssfrom=rxdemod

;txctcssdefault=100.0

;rxctcssfreqs=100.0;67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250.3

;txctcssfreqs=100.0;67.0,71.9,74.4,77.0,79.7,82.5,85.4,88.5,91.5,94.8,97.4,100.0,103.5,107.2,110.9,114.8,118.8,123.0,127.3,131.8,136.5,141.3,146.2,151.4,156.7,162.2,167.9,173.8,179.9,186.2,192.8,203.5,210.7,218.1,225.7,233.6,241.8,250.3

rxctcssoverride=1
plfilter=yes


rxctcssrelax=1    ; reduce talkoff from radios w/o CTCSS Tx HPF
             ; Do not change this, leave this as a 1

deemphasis = no      ; enable de-emphasis (input from discriminator)

rxondelay = 10          ; number of 20ms intervals to hold off receiver 
turn-on indication

rxboost = 0             ; 0 = 20db attenuator inserted, 1= 20db 
attenuator removed
                         ; Set to 1 for additonal gain if using a 
low-level receiver output

; Transmitter parameters

txboost = 0

txmixa = voice          ; Left channel output (A): no,voice
                         ; no - Do not output anything
                         ; voice - output voice only

txmixb = no            ; Right channel output (B): no,voice
                         ; no - Do not output anything
                         ; voice - output voice only

invertptt = 0           ; Invert PTT: 0,1 ( 0 - ground to transmit, 1 - 
open to transmit )

preemphasis = 0           ; Perform standard 6db/octave pre-emphasis

rxdemod=flat
txprelim=yes
txlimonly=no

; pager = no            ; no,a,b (e.g. pager = b means "put the normal 
repeat audio on channel A, and the pager audio on channel B")

; duplex3 = 0           ; duplex 3 gain setting (0 to disable)

#includeifexists custom/simpleusb.conf

-----------------------------------------------------------------------------
...mike/kb8jnm



On 12/22/2018 6:06 PM, ea8ee wrote:
> I have used my node as a hub for a long time and now I want to use it 
> as a simple usb with uri which files I should modify
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20181222/65900efb/attachment.html>