[App_rpt-users] Rpi3 on 29655
ARS W5OMR
ars.w5omr at gmail.com
Mon Feb 19 04:14:18 UTC 2018
you missed the part about the URI not being connected to the repeater,
just the usb cord to the pi... and the xmit led was lit. THAT was the
reason it was inverted.
On Sun, Feb 18, 2018 at 10:04 PM, Mike <mike at midnighteng.com> wrote:
> I dont think you should be inverting the logic on the ptt before you invert the logic on the receiver first.
> The ptt was up because the rx logic is wrong
> Otherwise it could not time out
>
> ...mike/kn8jnm
>
> Mike / Sent While Mobile
>
>> On Feb 18, 2018, at 10:27 PM, ARS W5OMR <ars.w5omr at gmail.com> wrote:
>>
>> I'm at my wit's end...
>> Somewhere between asterisk -Rcvvvv and modules.conf and 'usbradio.conf
>> ... ARRRHGGG!
>>
>> I know, you've been there, too - I've not had this stuff up and
>> running for over 3 years, I've forgotten some of the most important
>> things I knew...
>> Steve/N4IRS, great guy that he is, helped me tremendously the other
>> day and all was 'ok'. It wasn't quite done, but at the time, I felt
>> confident it was merely minor tweeking... I still had to make an
>> interface cable for the repeater to the URIx but, even without a radio
>> connected, I was connecting (monitor mode) to other nodes. That was
>> cool! It was PROGRESS!
>> But, the red LED on the URI stayed on. Even though there wasn't a
>> radio connected, I knew it wasn't supposed to be on. That meant it
>> was sending the 'xmit' signal out. Hell, even in the node status,
>> it's saying it's timing out and I don't know where else to tell
>> allstar that it's not even receiving a signal. First thing I did, was
>> modify usbradio.conf and inverted PTT and that shut it off. The
>> voltage on the output of the URI (Pins 1 (PTT) and 13 (GND)) 'floats'
>> somewhere around 0.65 to 0.72v, but when it's transmitting, it is
>> pulled DOWN to 0v. That's opposite of inverting PTT from 0 to 1.
>> (head scratch)
>>
>> This is on a Raspberry Pi3 connecting to a Motorola R100 repeater.
>>
>> Here are the .conf files, if someone wouldn't mind having a gander....
>>
>>
>> iax.conf
>> ----------
>>
>> ; Inter-Asterisk eXchange driver definition
>> ; http://docs.allstarlink.org/drupal/node/15
>>
>> ; ulaw, alaw, GSM and ADPCM should only be used,
>> ; the rest of the standard Asterisk codecs
>> ; (speex, ilbc, lpc10, etc) should be avoided.
>>
>> ; The ulaw and alaw codecs have the best audio quality,
>> ; followed by ADPCM, and lastly GSM,
>> ; Bandwidth used is in the reverse order to audio quality.
>> ; GSM uses the least bandwidth, and alaw/ulaw the most.
>>
>> ; CODEC AUDIO QUALITY BANDWIDTH (including IP and
>> Ethernet headers)
>> ; ULAW best 87 kbps
>> ; ADPCM good 55 kbps
>> ; GSM mediocre 36 kbps
>>
>>
>> [general]
>> bindport = 4569 ; bindport and bindaddr may be specified
>> ; NOTE: bindport must be specified BEFORE
>> ; bindaddr or may be specified on a specific
>> ; bindaddr if followed by colon and port
>> ; (e.g. bindaddr=192.168.0.1:4569)
>>
>> ; bindaddr = 192.168.0.1 ; more than once to bind to multiple
>> ; addresses, but the first will be the
>> ; default
>>
>> disallow = all ; The permitted codecs for outgoing connections
>> ; Audio Quality Bandwidth
>> allow = ulaw ; best 87 kbps
>> allow = adpcm ; good 55 kbps
>> allow = gsm ; medicore 36 kbps
>>
>> jitterbuffer = yes
>> forcejitterbuffer = yes
>> dropcount = 2
>> maxjitterbuffer = 4000
>> maxjitterinterps = 10
>> resyncthreshold = 1000
>> maxexcessbuffer = 80
>> minexcessbuffer = 10
>> jittershrinkrate = 1
>> tos = 0x1E
>> autokill = yes
>> delayreject = yes
>> ; iaxthreadcount = 30
>> ; iaxmaxthreadcount = 150
>>
>> register = 29655:xxxxx at register.allstarlink.org ; This must be changed
>> to your node number, password
>> ; remove the leading ";"
>>
>> ; Incoming radio connections
>>
>> [radio]
>> type = user
>> disallow = all
>> allow = ulaw
>> allow = adpcm
>> allow = gsm
>>
>> codecpriority = host
>> context = radio-secure
>> transfer = no
>>
>> [iaxrpt] ; Connect from iaxrpt Username field
>> (PC AllStar Client)
>> type = user ; Notice type is user here <---------------
>> context = iaxrpt ; Context to jump to in extensions.conf
>> auth = md5
>> secret = Your_Secret_Pasword_Here
>> host = dynamic
>> disallow = all
>> allow = ulaw
>> allow = adpcm
>> allow = gsm
>> transfer = no
>>
>> [iaxclient] ; Connect from iax client (Zoiper...)
>> type = friend ; Notice type here is friend <--------------
>> context = iax-client ; Context to jump to in extensions.conf
>> auth = md5
>> secret = Your_Secret_Password_Here
>> host = dynamic
>> disallow = all
>> allow = ulaw
>> allow = adpcm
>> allow = gsm
>> transfer = no
>>
>> [allstar-sys]
>> type = user
>> context = allstar-sys
>> auth = rsa
>> inkeys = allstar
>> disallow = all
>> allow = ulaw
>>
>> [allstar-public]
>> type = user
>> context = allstar-public
>> auth = md5
>> secret = allstar
>> disallow = all
>> allow = ulaw
>> allow = gsm
>>
>> ; The following should be un-commented to support Allstar Autopatch service
>> ; [allstar-autopatch]
>> ; type = peer
>> ; host = register.allstarlink.org
>> ; username = <One of the Node numbers on this server>
>> ; secret = <The node password for the above node>
>> ; auth = md5
>> ; disallow = all
>> ; allow = ulaw
>> ; transfer = no
>> ======================================
>>
>> rpt.conf
>> ---------
>> ; Radio Repeater configuration file (for use with app_rpt)
>>
>> ; Your Repeater
>>
>>
>> [29655] ; Change this to your assigned node number
>>
>> ; Must also be enabled in modules.conf
>> ; Rx audio/signalling channel. Choose ONLY 1 per node stanza
>>
>> ; Enable the selected channel driver in modules.conf !!!
>> ; rxchannel = dahdi/pseudo ; No radio (hub)
>> ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
>> ; rxchannel = Pi/1 ; Raspberry Pi PiTA
>> rxchannel = Radio/usb_29655 ; USBRadio (DSP)
>> ; rxchannel = Dahdi/1 ; PCI Quad card
>> ; rxchannel = Beagle/1 ; BeagleBoard
>> ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
>>
>> duplex = 2 ; 0 = Half duplex with no
>> telemetry tones or hang time.
>> ; Special Case: Full
>> duplex if linktolink is set to yes.
>> ; This mode is preferred
>> when interfacing with an external multiport repeater controller.
>> ; Comment out idrecording and idtalkover to suppress IDs also
>> ; 1 = Half duplex with
>> telemetry tones and hang time. Does not repeat audio.
>> ; This mode is preferred
>> when interfacing a simplex node.
>> ; 2 = Full Duplex with
>> telemetry tones and hang time.
>> ; This mode is preferred
>> when interfacing a repeater.
>> ; 3 = Full Duplex with
>> telemetry tones and hang time, but no repeated audio.
>> ; 4 = Full Duplex with
>> telemetry tones and hang time. Repeated audio only when the autopatch
>> is down.
>>
>> linktolink = no ; disables forcing physical half-duplex operation of
>> main repeater while
>> ; still keeping half-duplex semantics (optional)
>>
>> linkmongain = 0 ; Link Monitor Gain adjusts the audio level of
>> monitored nodes when a signal from another node or the local receiver
>> is received.
>> ; If linkmongain is set to a negative number the monitored audio will
>> decrease by the set amount in db.
>> ; If linkmongain set to a positive number monitored audio will
>> increase by the set amount in db.
>> ; The value of linkmongain is in db. The default value is 0 db.
>>
>> erxgain = -3 ; Echolink receive gain adjustment
>> ; Note: Gain is in db-volts (20logVI/VO)
>> etxgain = 3 ; Echolink transmit gain adjustment
>> ; Note: Gain is in db-volts (20logVI/VO)
>> ;eannmode = 1 ; 1 = Say only node number on
>> echolink connects (default = 1)
>> ; 2 = say phonetic call sign
>> only on echolink connects
>> ; 3 = say phonetic call sign
>> and node number on echolink connects
>>
>> ;controlstates = controlstates ; system control state stanza
>>
>> scheduler = schedule ; scheduler stanza
>> functions = functions ; Repeater Function stanza
>> phone_functions = functions ; Phone Function stanza
>> link_functions = functions ; Link Function stanza
>>
>> telemetry = telemetry ; Telemetry stanza
>> morse = morse ; Morse stanza
>> wait_times = wait-times ; Wait times stanza
>>
>> context = radio ; dialing context for phone
>> callerid = "Repeater" <0000000000> ; callerid for phone calls
>> accountcode = RADIO ; account code (optional)
>>
>> hangtime = 1000 ; squelch tail hang time (in ms) (optional, default 5
>> seconds, 5000 ms)
>> althangtime = 1000 ; longer squelch tail
>> totime = 300000 ; transmit time-out time (in ms) (optional, default 3
>> minutes 180000 ms)
>>
>> idrecording = |iW5OMR/R ; id recording or morse string
>> see http://ohnosec.org/drupal/node/87
>> idtalkover = |iW5OMR ; Talkover ID (optional)
>> default is none see http://ohnosec.org/drupal/node/129
>> idtime = 540000 ; id interval time (in ms) (optional) Default 5
>> minutes (300000 ms)
>> politeid = 30000 ; time in milliseconds before ID timer expires to try
>> and ID in the tail. (optional, default 30000)
>>
>> unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if
>> the node is not connected to any other nodes. (optional, default is
>> none)
>> remotect = ct3 ; remote linked courtesy tone (indicates a remote is in
>> the list of links)
>> linkunkeyct = ct8 ; sent when a transmission received over the link unkeys
>> ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is
>> connected to this node (hosted on the same PC).
>>
>> ;connpgm = yourconnectprogram ; Disabled. Execute a program you
>> specify on connect. (default)
>> ; passes 2 command line arguments to your program:
>> ; 1. node number in this stanza (us)
>> ; 2. node number being connected to us (them)
>> ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you
>> specify on disconnect. (default)
>> ; passes 2 command line arguments to your program:
>> ; 1. node number in this stanza (us)
>> ; 2. node number being disconnected from us (them)
>>
>> ;lnkactenable = 0 ; Set to 1 to enable the link activity timer.
>> Applicable to standard nodes only.
>>
>> ;lnkacttime = 1800 ; Link activity timer time in seconds.
>> ;lnkactmacro = *52 ; Function to execute when link activity timer expires.
>> ;lnkacttimerwarn = 30seconds ; Message to play when the link activity
>> timer has 30 seconds left.
>>
>> ;remote_inact_timeout = ; Specifies the amount of time without keying
>> from the link. Set to 0 to disable timeout. (15 * 60)
>> ;remote_timeout = ; Session time out for remote base. Set to 0 to
>> disable. (60 * 60)
>> ;remote_timeout_warning_freq = ; 30
>> ;remote_timeout_warning = ; (3 * 60)
>>
>> ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.
>>
>> holdofftelem = 1 ; Hold off all telemetry when signal is present on
>> receiver or from connected nodes
>> ; except when an ID needs to be done and there is a signal coming from
>> a connected node.
>>
>> telemdefault = 1 ; 0 = telemetry output off
>> ; 1 = telemetry output on (default = 1)
>> ; 2 = timed telemetry output
>> on command execution and for a short time thereafter.
>>
>> telemdynamic = 1 ; 0 = disallow users to change
>> the local telemetry setting with a COP command,
>> ; 1 = Allow users to change
>> the setting with a COP command. (default = 1)
>>
>> ;beaconing = 0 ; Send ID regardless of repeater activity (Required in
>> the UK, but probably illegal in the US)
>>
>> parrotmode = 0 ; 0 = Parrot Off (default = 0)
>> ; 1 = Parrot On Command
>> ; 2 = Parrot Always
>> ; 3 = Parrot Once by Command
>>
>> parrottime = 1000 ; Set the amount of time in milliseconds
>> ; to wait before parroting what was received
>>
>> ;rxnotch=1065,40 ; (Optional) Notch a
>> particular frequency for a specified
>> ; b/w. app_rpt must have been
>> compiled with
>> ; the notch option
>>
>> startup_macro=*982 ; Macro to run at startup (optional)
>>
>> nodenames = /var/lib/asterisk/sounds/rpt/nodenames ; Point to nodename
>> sound directory
>>
>> ; *** Status Reporting ***
>>
>> ; Uncomment either group following two statpost lines to report the
>> status of your node to stats.allstarlink.org
>> ; depending on whether you are running ACID, Debian or Limey Linux.
>> ; The difference is simply where your wget is located.
>>
>> ; ** For ACID and Debian ***
>> statpost_program =
>> /usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> ; ** For Limey Linux **
>> ;statpost_program =
>> /bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> ;statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> [functions]
>>
>> ; Prefix Functions
>> ; *1 Disconnect Link
>> ; *2 Monitor Link
>> ; *3 Connect Link
>> ; *4 Command Mode
>> ; *5 Macros
>> ; *6 User Functions
>> ; *7 Connection Status/Functions
>> ; *8 User Functions
>> ; *9 User Functions
>> ; *0 User Functions
>>
>> ; *A User Functions
>> ; *B User Functions
>> ; *C User Functions
>> ; *D User Functions
>>
>>
>> ; Mandatory Command Codes
>> ; http://docs.allstarlink.org/drupal/node/91
>>
>> 1 = ilink,1 ; Disconnect specified link
>> 2 = ilink,2 ; Connect specified link -- monitor only
>> 3 = ilink,3 ; Connect specified link -- tranceive
>> 4 = ilink,4 ; Enter command mode on specified link
>> 70 = ilink,5 ; System status
>> 99 = cop,6 ; PTT (phone mode only)
>>
>> ; End Mandatory Command Codes
>>
>> ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
>>
>> ; Macro Commands
>> 5 = macro
>>
>> ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
>>
>> ; Autopatch Commands
>> ; Note, This may be a good place for other 2 digit frequently used commands
>>
>> 61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up
>> 62 = autopatchdn ;
>> Autopatch down
>>
>> ; autopatchup can optionally take comma delimited setting=value pairs:
>>
>> ; context = string ; Override default context with "string"
>> ; dialtime = ms ; Specify the max number of milliseconds between phone
>> number digits (1000 milliseconds = 1 second)
>> ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up
>> ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls
>> ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send
>> patch down message when called party hangs up
>> ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
>>
>> ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
>>
>> ; Status Commands
>>
>> ; 1 - Force ID (global)
>> ; 2 - Give Time of Day (global)
>> ; 3 - Give software Version (global)
>> ; 4 - Give GPS location info
>> ; 5 - Last (dtmf) user
>> ; 11 - Force ID (local only)
>> ; 12 - Give Time of Day (local only)
>>
>> 721 = status,1 ; Force ID (global)
>> 722 = status,2 ; Give Time of Day (global)
>> 723 = status,3 ; Give software Version (global)
>> 724 = status,4 ; Give GPS location info
>> 725 = status,5 ; Last (dtmf) user
>> 711 = status,11 ; Force ID (local only)
>> 712 = status,12 ; Give Time of Day (local only)
>>
>> ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
>>
>> ; Link Commands
>>
>> ; 1 - Disconnect specified link
>> ; 2 - Connect specified link -- monitor only
>> ; 3 - Connect specified link -- tranceive
>> ; 4 - Enter command mode on specified link
>> ; 5 - System status
>> ; 6 - Disconnect all links
>> ; 7 - Last Node to Key Up
>> ; 8 - Connect specified link -- local monitor only
>> ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
>> ; 10 - Disconnect all RANGER links (except permalinks)
>> ; 11 - Disconnect a previously permanently connected link
>> ; 12 - Permanently connect specified link -- monitor only
>> ; 13 - Permanently connect specified link -- tranceive
>> ; 15 - Full system status (all nodes)
>> ; 16 - Reconnect links disconnected with "disconnect all links"
>> ; 17 - MDC test (for diag purposes)
>> ; 18 - Permanently Connect specified link -- local monitor only
>>
>> ; ilink commands 1 through 5 are defined in the Mandatory Command section
>>
>> 806 = ilink,6 ; Disconnect all links
>> 807 = ilink,7 ; Last Node to Key Up
>> 808 = ilink,8 ; Connect specified link -- local monitor only
>> 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999
>> replace 1999 with 0 for all connected nodes
>> ; *** I'll change this later - just
>> noticed it ge/omr ***
>> 810 = ilink,10 ; Disconnect all RANGER links (except permalinks)
>> 811 = ilink,11 ; Disconnect a previously permanently connected link
>> 812 = ilink,12 ; Permanently connect specified link -- monitor only
>> 813 = ilink,13 ; Permanently connect specified link -- tranceive
>> 815 = ilink,15 ; Full system status (all nodes)
>> 816 = ilink,16 ; Reconnect links disconnected with
>> "disconnect all links"
>> 817 = ilink,17 ; MDC test (for diag purposes)
>> 818 = ilink 18 ; Permanently Connect specified link -- local
>> monitor only
>>
>> ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
>>
>> ; Control operator (cop) functions. Change these to something other
>> than these codes listed below!
>>
>> 901 = cop,1 ; System warm boot
>> 902 = cop,2 ; System enable
>> 903 = cop,3 ; System disable
>>
>> 904 = cop,4 ; Test tone on/off (toggle)
>> 905 = cop,5 ; Dump system variables on console (debug use only)
>>
>> 907 = cop,7 ; Time out timer enable
>> 908 = cop,8 ; Time out timer disable
>>
>> 909 = cop,9 ; Autopatch enable
>> 910 = cop,10 ; Autopatch disable
>>
>> 911 = cop,11 ; User linking functions enable
>> 912 = cop,12 ; User linking functions disable
>>
>> 913 = cop,13 ; Query system control state
>> 914 = cop,14 ; Set system control state
>>
>> 915 = cop,15 ; Scheduler enable
>> 916 = cop,16 ; Scheduler disable
>>
>> 917 = cop,17 ; User functions enable (time, id, etc)
>> 918 = cop,18 ; User functions disable
>>
>> 919 = cop,19 ; Select alternate hang time (althangtime)
>> 920 = cop,20 ; Select standard hangtime (hangtime)
>>
>> 921 = cop,21 ; Enable Parrot Mode
>> 922 = cop,22 ; Disable Parrot Mode
>> 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush)
>>
>> 924 = cop,24 ; Flush all telemetry
>> 925 = cop,25 ; Query last node un-keyed
>> 926 = cop,26 ; Query all nodes keyed/unkeyed
>> 930 = cop,30 ; Recall Memory Setting in Attached Xcvr
>>
>> 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr
>>
>> 932 = cop,32 ; Touchtone pad test: command + Digit string + # to
>> playback all digits pressed
>>
>> 933 = cop,33 ; Local Telemetry Output Enable
>> 934 = cop,34 ; Local Telemetry Output Disable
>> 935 = cop,35 ; Local Telemetry Output on Demand
>>
>> 936 = cop,36 ; Foreign Link Local Output Path Enable
>> 937 = cop,37 ; Foreign Link Local Output Path Disable
>> 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry
>> 939 = cop,39 ; Foreign Link Local Output Path on Demand
>>
>> 942 = cop,42 ; Echolink announce node # only
>> 943 = cop,43 ; Echolink announce node Callsign only
>> 944 = cop,44 ; Echolink announce node # & Callsign
>>
>> 945 = cop,45 ; Link Activity timer enable
>> 945 = cop,46 ; Link Activity timer disable
>> 947 = cop,47 ; Reset "Link Config Changed" Flag
>>
>> 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)
>>
>> 949 = cop,49 ; Disable incoming connections (control state noice)
>> 950 = cop,50 ; Enable incoming connections (control state noicd)
>>
>> 951 = cop,51 ; Enable sleep mode
>> 952 = cop,52 ; Disable sleep mode
>> 953 = cop,53 ; Wake up from sleep
>> 954 = cop,54 ; Go to sleep
>> 955 = cop,55 ; Parrot Once if parrot mode is disabled
>>
>> 956 = cop,56 ; Rx CTCSS Enable
>> 957 = cop,57 ; Rx CTCSS Disable
>>
>> 958 = cop.58 ; Tx CTCSS On Input only Enable
>> 959 = cop,59 ; Tx CTCSS On Input only Disable
>>
>> 960 = cop,60 ; Send MDC-1200 Burst
>> (cop,60,type,UnitID[,DestID,SubCode])
>> ; Type is 'I' for PttID, 'E'
>> for Emergency, and 'C' for Call
>> ; (SelCall or Alert), or 'SX'
>> for STS (ststus), where X is 0-F.
>> ; DestID and subcode are only
>> specified for the 'C' type message.
>> ; UnitID is the local systems
>> UnitID. DestID is the MDC1200 ID of
>> ; the radio being called, and
>> the subcodes are as follows:
>> ; Subcode '8205' is Voice
>> Selective Call for Spectra ('Call')
>> ; Subcode '8015' is Voice
>> Selective Call for Maxtrac ('SC') or
>> ; Astro-Saber('Call')
>> ; Subcode '810D' is Call Alert
>> (like Maxtrac 'CA')
>>
>> 961 = cop,61 ; Send Message to USB to
>> control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
>> 962 = cop,62 ; Send Message to USB to
>> control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
>>
>> 963 = cop,63 ; Send pre-configred APRSTT
>> notification (cop,63,CALL[,OVERLAYCHR])
>> 964 = cop,64 ; Send pre-configred APRSTT
>> notification, quietly (cop,64,CALL[,OVERLAYCHR])
>> 965 = cop,65 ; Send POCSAG page (equipped
>> channel types only)
>>
>> 982 = playback,rpt/node_enabled ; Report node enabled to transmitter
>>
>> [functions-remote]
>>
>> 0 = remote,1 ; Retrieve Memory
>> 1 = remote,2 ; Set freq.
>> 2 = remote,3 ; Set tx PL tone
>> 3 = remote,4 ; Set rx PL tone
>> 40 = remote,100 ; Rx PL off
>> 41 = remote,101 ; Rx PL on
>> 42 = remote,102 ; Tx PL off
>> 43 = remote,103 ; Tx PL on
>> 44 = remote,104 ; Low Power
>> 45 = remote,105 ; Medium Power
>> 46 = remote,106 ; High Power
>> 711 = remote,107 ; Bump -20
>> 714 = remote,108 ; Bump -100
>> 717 = remote,109 ; Bump -500
>> 713 = remote,110 ; Bump +20
>> 716 = remote,111 ; Bump +100
>> 719 = remote,112 ; Bump +500
>> 721 = remote,113 ; Scan - slow
>> 724 = remote,114 ; Scan - quick
>> 727 = remote,115 ; Scan - fast
>> 723 = remote,116 ; Scan + slow
>> 726 = remote,117 ; Scan + quick
>> 729 = remote,118 ; Scan + fast
>> 79 = remote,119 ; Tune
>> 51 = remote,5 ; Long status query
>> 52 = remote,140 ; Short status query
>> 67 = remote,210 ; Send a *
>> 69 = remote,211 ; Send a #
>> ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login.
>> ; Define a different dtmf
>> sequence for each user which is
>> ; authorized to use the remote
>> base to control access to it.
>> ; For examble
>> 9139583=remote,99,WB6NIL,G would grant access to
>> ; the remote base and announce
>> WB6NIL as being logged in.
>> ; Another entry,
>> 9148351=remote,99,WA6ZFT,E would grant access to
>> ; the remote base and announce
>> WA6ZFT as being logged in.
>> ; When the remote base is
>> disconnected from the originating node, the
>> ; user will be logged out. The
>> LICENSETAG argument is used to enforce
>> ; tx frequency limits. See [txlimits] below.
>> 85 = cop,6 ; Remote base telephone key
>>
>>
>> [telemetry]
>>
>> ; Telemetry entries can be shared across all repeaters, or defined for
>> each repeater.
>> ; Can be a tone sequence, morse string, or a file
>> ;
>> ; |t - Tone escape sequence
>> ;
>> ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2,
>> duration, amplitude)
>> ; Single frequencies are created by setting freq1 or freq2 to zero.
>> ;
>> ; |m - Morse escape sequence
>> ;
>> ; Sends Morse code at the telemetry amplitude and telemetry frequency
>> as defined in the
>> ; [morse] section.
>> ;
>> ; Follow with an alphanumeric string
>> ;
>> ; |i - Morse ID escape sequence
>> ;
>> ; Sends Morse code at the ID amplitude and ID frequency as defined in the
>> ; [morse] section.
>> ;
>>
>> ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
>> ct2 = |t(660,880,150,2048)
>> ct3 = |t(440,0,150,4096)
>> ct4 = |t(550,0,150,2048)
>> ct5 = |t(660,0,150,2048)
>> ct6 = |t(880,0,150,2048)
>> ct7 = |t(660,440,150,2048)
>> ct8 = |t(700,1100,150,2048)
>> ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
>> remotemon = |t(1209,0,50,2048) ;
>> local courtesy tone when receive only
>> remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local
>> courtesy tone when linked Trancieve mode
>> cmdmode = |t(900,903,200,2048)
>> functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
>> pfxtone = |t(350,440,30000,3072)
>> patchup = rpt/callproceeding
>> patchdown = rpt/callterminated
>>
>> ; As far as what the numbers mean,
>> ; (000,000,010,000)
>> ; | | | |-------amplitude
>> ; | | |-------------duration
>> ; | |-------------------Tone 2
>> ; |-------------------------Tone 1
>>
>> ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
>> ; Use it for a delay. Fine tuning for how long before telemetry is
>> sent, in conjunction with the telemdelay parameter)
>> ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay,
>> amplitude of 2048.
>>
>> ; Morse code parameters, these are common to all repeaters.
>>
>> [morse]
>> speed = 20 ; Approximate speed in WPM
>> frequency = 800 ; Morse Telemetry Frequency
>> amplitude = 4096 ; Morse Telemetry Amplitude
>> idfrequency = 1065 ; Morse ID Frequency
>> idamplitude = 1024 ; Morse ID Amplitude
>>
>> ;
>> ; This section allows wait times for telemetry events to be adjusted
>> ; A section for wait times can be defined for every repeater
>> ;
>>
>> [wait-times]
>> telemwait = 1000 ; Time to wait before sending
>> most telemetry
>> idwait = 500 ; Time to wait before starting ID
>> unkeywait = 500 ; Time to wait after unkey
>> before sending CT's and link telemetry
>> calltermwait = 500 ; Time to wait before
>> announcing "call terminated"
>>
>> ;
>> ; This is where you define your nodes which cam be connected to.
>> ;
>>
>> [nodes]
>> ; Note, if you are using automatic update for allstar link nodes,
>> ; no allstar link nodes should be defined here. Only place a definition
>> ; for your local nodes, and private (off of allstar link) nodes here.
>>
>> 29655 = radio at 127.0.0.1:4569/29655,NONE ; This must be changed to your
>> node number
>> ; and iax port number if not the default
>> ; Memories for remote bases
>>
>> [memory]
>> ;00 = 146.580,100.0,m
>> ;01 = 147.030,103.5,m+t
>> ;02 = 147.240,103.5,m+t
>> ;03 = 147.765,79.7,m-t
>> ;04 = 146.460,100.0,m
>> ;05 = 146.550,100.0,m
>>
>> ; Place command macros here
>>
>> [macro]
>> ;1 = *32011#
>> ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
>> ;3 = *32001*32011*32050*32030*32060#
>>
>>
>> ; Data Acquisition configuration
>>
>> ;[daq-list]
>> ;device = device_name1
>> ;device = device_name2
>>
>> ;Where: device_name1 and device_name2 are stanzas you define in this file
>>
>> ;device = daq-cham-1
>>
>> ; Device name
>>
>> ;[daq-cham-1] ; Defined in [daq-list]
>> ;hwtype = uchameleon ; DAQ hardware type
>> ;devnode = /dev/ttyUSB0 ; DAQ device node (if required)
>> ;1 = inadc ; Pin definition for an ADC channel
>> ;2 = inadc
>> ;3 = inadc
>> ;4 = inadc
>> ;5 = inadc
>> ;6 = inadc
>> ;7 = inadc
>> ;8 = inadc
>> ;9 = inp ; Pin definition for an input with a weak pullup resistor
>> ;10 = inp
>> ;11 = inp
>> ;12 = inp
>> ;13 = in ; Pin definition for an input without a weak pullup resistor
>> ;14 = out ; Pin definition for an output
>> ;15 = out
>> ;16 = out
>> ;17 = out
>> ;18 = out
>>
>> ;[meter-faces]
>>
>> ;face = scale(scalepre,scalediv,scalepost),word/?,...
>> ;
>> ; scalepre = offset to add before dividing with scalediv
>> ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for
>> 20 volts).
>> ; scalepost = offset to add after dividing with scalediv
>> ;
>> ;face = range(X-Y:word,X2-Y2:word,...),word/?,...
>> ;face = bit(low-word,high-word),word/?,...
>> ;
>> ; word/? is either a word in /var/lib/asterisk/sounds or one of its
>> subdirectories,
>> ; or a question mark which is a placeholder for the measured value.
>> ;
>> ;
>> ; Battery voltage 0-20 volts
>> ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
>> ; 4 quadrant wind direction
>> ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
>> ; LM34 temperature sensor with 130 deg. F full scale
>> ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
>> ; Status poll (non alarmed)
>> ;light = bit(ha/off,ha/on),ha/light,?
>>
>> ;[alarms]
>> ;
>> ;tag = device,pin,node,ignorefirst,func-low,func-hi
>> ;
>> ;tag = a unique name for the alarm
>> ;device = daq device to poll
>> ;pin = the device pin to be monitored
>> ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it
>> ;node = the node number to execute the function on
>> ;func-low = the DTMF function to execute on a high to low transition
>> ;func-high = the DTMF function to execute on a low to high transition
>> ;
>> ; a '-' as a function name is shorthand for no-operation
>> ;
>> ;door = daq-cham-1,9,1,2017,*7,-
>> ;pwrfail = daq-cham-1,10,0,2017,*911111,-
>> ;
>> ; Control states
>> ; Allow several control operator functions to be changed at once using
>> one command (good for scheduling)
>> ;
>> ;[controlstates]
>> ;statenum = copcmd,[copcmd]...
>> ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
>> ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation
>> ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation
>>
>> ; Scheduler - execute a macro at a given time
>>
>> [schedule]
>> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>> ;2 = 00 00 * * * ; at midnight, execute macro 2.
>>
>> ==============================================
>>
>> echolink.conf (not that I think -this- part matters much)
>>
>> [el0]
>> call = W5OMR/R ; Change this!
>> pwd = xxxxx ; Change this!
>> name = Geoff ; Change this!
>> qth = Splendora ; Change this!
>> email = INVALID ; Change this!
>> node = 004817 ; Change this!
>> ; Data for EchoLink Status Page
>> lat = 0.0 ; Latitude in decimal degrees
>> lon = 0.0 ; Longitude in decimal degrees
>> freq = 0.0 ; not mandatory Frequency in MHz
>> tone = 0.0 ; not mandatory CTCSS Tone (0 for none)
>> power = 5 ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W,
>> 9=81W (Power in Watts)
>> height = 2 ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560
>> 9=5120 (AMSL in Feet)
>> gain = 9 ; Gain in db (0-9)
>> dir = 0 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg
>> 7=315deg 8=360deg (Direction)
>>
>> maxstns = 5 ; Max Stations
>>
>> rtcptimeout = 10
>> recfile = /tmp/echolink_recorded.gsm ;
>> astnode = 29655 ; Change this!
>> context = radio-secure ; Default in code is echolink-in
>>
>> ; Max 3 servers
>> server1 = nasouth.echolink.org
>> server2 = naeast.echolink.org
>> server3 = server3.echolink.org
>>
>> ; To deny w6xxx you would add the statement: deny = w6xxx
>> ; To prohibit computer-based connections you would write: permit = *-*
>> ; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
>>
>> ; permit ; comma delimited list of callsign, type (-r)
>> ; deny
>>
>>
>> ; Remote text commands thru netcat:
>> ; o.conip <IPaddress> (request a connect)
>> ; o.dconip <IPaddress> (request a disconnect)
>> ; o.rec (turn on/off recording)
>>
>> ; ipaddr
>> ; port
>>
>> ===============================
>>
>> So, does anything 'jump out' at ya?
>>
>>
>> --
>>
>> 73 = Best Regards,
>> -Geoff/W5OMR
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at lists.allstarlink.org
>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
Operating your AM rig without a scope is like driving our car at night
without headlights. (~K4KYV)
73 = Best Regards,
-Geoff/W5OMR
More information about the App_rpt-users
mailing list