Hi Dave, You can also try running K0KN's upgrade script. Every now and then I have a node act up and that fixes it. http://www.qsl.net/k0kn/scripts.html If you run nodesetup.sh you should able to re-download your config files too. On Mon, Sep 7, 2015 at 8:33 PM, kk6ecm <kk6ecm@gmail.com> wrote:
My experience says asterisk is not happy. Assuming you have gone though the tune process for your URI, it could mean that devstr=a-b in usbradio_tune_xxx does not match the USB address as seen in lsusb, e.g.
Bus 00a Device 00b: ID 0d8c:013a C-Media Electronics, Inc.
If that is OK, then I'd check for a typo in one of the asterisk .conf files.
Bob kk6ecm
-----Original Message----- From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Dave Newmyer Sent: Monday, September 07, 2015 7:09 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Problem with a post-install on an inactive node(28781)
Hello,
I have been attempting to get my simplex node back up and running after being off of the air for a couple of years. The ULI device and radio are the same, but the computer, installation software, ect. are all different. I am using a new install from an acid-centos.iso I downloaded a couple of days ago.
At post-install, I get the following: mpg123:no process killed. Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk
This repeats over and over. I checked the archives, and found a series of postings from someone who had a similar problem some time back. In reading the log file /var/log/asterisk/messages the errors refer to a problem with Zaptel.
One of the suggestions was to update Asterisk from SVN, then update Zaptel.
After doing this, Asterisk started, and I was able to perform system info and time DTMF commands to my node.
Later, I tried resetting the computer and after restarting it, I am back to the mpg123:no process killed. Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk
Errors over and over and over again.
I am thinking that possibly my config files on the AllStar.org website might have an issue, but on one of my re-installs of the software from the cd, I chose not to download the remote configs.
Anyway, I am not sure what to try next.
73,
Dave N N0KM
--- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.