I believe either you need to set carrierfrom or ctcssfrom or both, to usb or usbinvert. A no sets it to ignore that input. I have mine setup to the following: carrierfrom=usbinvert ctcssfrom=usbinvert Monty On Thu, May 3, 2012 at 3:40 PM, David Kierzkowski <dave_k_420@yahoo.com>wrote:
tried it - didn't help i diffed the entire etc dir between the 2 configs portal pushed configs. rpt.conf rxchannel value and the presence of radiousb.conf are the only things that change. so i renamed a copy of radiousb.conf to simpleusb.conf and changed the rpt.conf to point to it... and it still does not work!? Something else is going on in asterisk that i cant figure out this is the asterisk verbose output when i key and keyup the java client if it helps
Node Variable dump for node 28522: RPT_NUMLINKS=1 RPT_LINKS=1,TKD8EYF RPT_NUMALINKS=1 RPT_ALINKS=1,KD8EYFTK RPT_ETXKEYED=1 RPT_RXKEYED=1 RPT_AUTOPATCHUP=0 RPT_TXKEYED=0 -- 8 variables Node Variable dump for node 28522: RPT_NUMLINKS=1 RPT_LINKS=1,TKD8EYF RPT_NUMALINKS=1 RPT_ALINKS=1,KD8EYFTU RPT_ETXKEYED=1 RPT_RXKEYED=1 RPT_AUTOPATCHUP=0 RPT_TXKEYED=0 -- 8 variables -- Hungup 'Zap/pseudo-991844848'
On 5/3/2012 6:12 PM, Tim Sawyer wrote:
Take out one of the usb stanzas in simpleusb.conf and then check your rpt.conf for a matching rxchannel
ie, either
rxchannel = SimpleUSB/usb
or
rxchannel = SimpleUSB/usb28522
depending which you leave in simpleusb.conf
-- Tim :wq
On May 3, 2012, at 2:43 PM, David Kierzkowski wrote:
Also i am currently using
carrierfrom=no ctcssfrom=no for the below config was jsut from trying to find a working combination when posted the first msg..
On 5/3/2012 5:33 PM, David Kierzkowski wrote:
I have a ACID install with URIx connected to a icom v8000. Want to setup as a simple repeater. Through the portal when setting the interface to simpleusb, no PTT will work, but i can hear recieved audio. if i setup the interface as usbradio (i dont want / radio is doing ctcss/ speak level audio ) then the radio will PTT and pass overmodulated audio (as expected) but no RX audio will pass.
i have a feeling theres a config issue with simpleusb.conf.. do u guys see anything? I dont know why it creates the [usb] device stanza. Also while in the simple_tune_usb.sh i can see and set the RX levels properly and manually flash the PTT.
[general]
[usb]
hdwtype=0 rxboost=1 txboost=1 carrierfrom=dsp ctcssfrom=dsp txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 eeprom=0
[usb28522]
hdwtype=0 rxboost=0 txboost=1 carrierfrom=usb ctcssfrom=usb txmixa=voice txmixb=no invertptt=0 duplex=0 rxondelay=1 eeprom=0
and here is simpleusb_tune_usb28522.conf [usb28522] ; name=usb28522 ; devicenum=2 devstr=4-4 rxmixerset=400 txmixaset=500 txmixbset=500
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users