Loren, It's really not about what radios you have but the signal logic of the COR line. If the logic for your controller is low=true meaning a 0v or low voltage level means it is actively receiving, The when you disconnect it, It will be true and bring up the repeater as if it was rxing a signal when you disconnect it because it is not getting a high level signal to say it is inactive. So... when you disconnect it, change the logic of the signal for cor input so it does not make the controller think the rx is active after you disconnect it. Example set the controller for high=true or a voltage level is a signal for active rx when/after disconnecting the rx. perhaps someone else can explain it better than I. ...mike/kb8jnm
-------- Original Message -------- Subject: Re: [App_rpt-users] Linking two nodes together From: Loren Tedford <lorentedford@gmail.com> Date: Fri, December 05, 2014 5:02 pm To: mike@midnighteng.com Cc: app_rpt mailing list <app_rpt-users@ohnosec.org>
All of my current radios are CM200s VHF and UHF on both repeater systems node radios are a combination of CM200s and I do have one Maxtrac VHF floating around here at the house.. Yes when i disconnect the RX side or turn off the RX radio it seems to hang open the transmitter with a silent hang.. Not sure about the whole cor thing didnt really change any settings on the radios or the URI at least related to cor.. If you have any ideas feel free to let me know will be testing a few things maybe it was because it was in Duplex=2 mode at the tx site when i did this test not sure when i changed the that line in the Rpt.conf to Duplex=1
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com http://kc9zhv.lorentedford.com
On Fri, Dec 5, 2014 at 12:28 PM, <mike@midnighteng.com> wrote:
I don't know what you are "unhooking" for the rx at rptr site but it could perhaps be "if the logic on the cor is inverted", it would say the rx is active when not present/disconnected.
...mike/kb8jnm
-------- Original Message -------- Subject: Re: [App_rpt-users] Linking two nodes together From: Loren Tedford <lorentedford@gmail.com> Date: Fri, December 05, 2014 1:14 pm To: Corey Dean <n3fe@repeater.net>, app_rpt mailing list <app_rpt-users@ohnosec.org>
Corey, Noticed one problem if i unhook the RX side at the repeater for some reason it hangs the transmitter open not sure exactly what i am missing here but if you think of some thing let me know love the *2 for connect think thats a great idea
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com Email: lorentedford@live.com Email: lorentedford@aol.com Email: LorenCS@Ltcraft.net Email: lorentedford@yahoo.com Email: loren@lorentedford.com <loren@lorentedford.com> Email: loren@richlandcountycomputers.com Phone: 618-553-0806 http://www.lorentedford.com http://www.Ltcraft.net <http://www.ltcraft.net/> http://www.richlandcountycomputers.com http://kc9zhv.lorentedford.com
On Fri, Dec 5, 2014 at 12:00 PM, Corey Dean <n3fe@repeater.net> wrote:
Unhook the rx from the repeater site and unhook the tx from your house and the. Just connect them together. You can also disable the rx at the repeater and do a *2 for receive only to the site at your house.
Corey
On Dec 5, 2014, at 12:54 PM, Loren Tedford <lorentedford@gmail.com> wrote:
Yes Doug was looking to link via Internet for now till I can find some one that really knows how to tune Duplexers.. lol... yea I have had bad look with 7 different radio communication companies around here getting this done either they lock open the repeater or you cant hear anyone through the recieve side of the system.. So my goal was to setup a node at the house for just RX use only and set up the Transmitter at the repeater site for now.. Internet link them Voice over ip node to node.. I have two URIs and two cables however one cable is a repeater cable suppose i could probably use this on the RX side then use the other one for the transmitter.. Just guessing Special Thanks goes out to Chris Curtis will try this thanks!! :) Any other thoughts or suggestions with this project please let me know..
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com http://kc9zhv.lorentedford.com
On Fri, Dec 5, 2014 at 9:50 AM, Doug Crompton <doug@crompton.com> wrote:
Do you mean linking via a normal Allstar link? or linking via RF. It is not clear what you are trying to do.
You can link two nodes privately if you know the IP address and port of each node. You just enter the info for the OTHER node in the nodes section of rpt.conf. Assuming you have a good Internet path once this is entered and Asterisk is restarted you should be able to connect. Of course you also need the port forwards in the routers also.
[nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here.
1998 = radio@ip.address.for.1999:port/1998,NONE
This show one end. The other end would be just the opposite. Port is only needed if it is other than the default 4569.
*73 DougWA3DSPhttp://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
------------------------------ Date: Fri, 5 Dec 2014 01:52:39 -0600 From: lorentedford@gmail.com To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Linking two nodes together
Need to kinda get some examples of how to link two nodes together examples lets say node 1 is at the repeater site and node 2 is at my house and lets say that I cant get some one to tune up my duplexer properly.. what is the best way to link two nodes together to make my repeater at least functional..
Thanks in advance Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com
http://kc9zhv.lorentedford.com
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.