As you said, it was when DIAL first released for the RPi so it's 1.0 From the asterisk CLI: rpt cmd 1999 cop 2 1999 <------------ system enable rpt cmd 1999 cop 3 1999 <------------ system disable replace 1999 with the node number On 5/26/2017 12:35 PM, Bob wrote:
Actually, just turn the repeater off, then later back on. Will test this. I see I don't have it in rpt.conf.
Also, how do I tell which version of DIAL I have installed?
Thanks,
Bob
------------------------------------------------------------------------
*From:*App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] *On Behalf Of *Bryan D. Boyle *Sent:* Friday, May 26, 2017 10:03 AM *To:* Users of Asterisk app_rpt *Subject:* Re: [App_rpt-users] Temporary stop, then restart asterisk
cop 2 system enable
cop 3 system disable
--
Bryan
Sent from my iPhone 6S...No electrons were harmed in the sending of this message.
On May 26, 2017, at 11:57, Mike - W5JR <w5jr.lists@gmail.com <mailto:w5jr.lists@gmail.com>> wrote:
Do want to stop AllStar/Asterisk or just turn the repeater off? There is a COP command for the latter. I'm not in front of a terminal to get you the command.
tnx Mike / W5JR Alpharetta GA
On May 26, 2017, at 11:46 AM, Bob Pyke <k6ecm1@gmail.com <mailto:k6ecm1@gmail.com>> wrote:
Hmmm... sounds like an update is in order :-)
Thanks much,
Bob
Sent from my iPhone
On May 26, 2017, at 8:41 AM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
OK,
/etc/init.d/asterisk stop <--- Stop asterisk
killall -9 asterisk <---------------- Make sure it's dead
ps ax | grep asterisk <--- Check to see if it's really dead
/etc/init.d/asterisk start <--- start asterisk
ps ax | grep asterisk <--- Check to see if it's really started
The newer release candidate fixes this.
73, Steve N4IRS
On 5/26/2017 11:37 AM, Bob Pyke wrote:
No. It will be off for several minutes, but I want it to stop when commanded, and start on command. We are conducting an exercise. I don't know the version, and logging into the node does not say. We've been operating, pretty much since the introduction of app_rpt on the RPi
Thanks
Sent from my iPhone
On May 26, 2017, at 8:31 AM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Bob,
Are you talking about "bouncing" asterisk? A stop followed by a rapid start? Which distribution and version are you running?
73, Steve N4IRS
On 5/26/2017 11:28 AM, Bob Pyke wrote:
I have a need to temporarily disable the repeater, then enable it. Timing is critical, so a delay is undesirable. What is the best way to accomplish this? I will be logged into the node.
Thanks,
Bob
Sent from my iPhone
_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org>
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If y
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.