I had included usbradio.conf in the original message. Mind you, the 'keyed state' is without the URI being connected to the repeater. Just the usb line to the rpi3. It's somewhere in one of the .conf files... damned if I know where. On Sun, Feb 18, 2018 at 10:05 PM, Mark Johnston <markjohnston73@gmail.com> wrote:
First off, the PTT should not key with no radio connected using usbradio.conf/discriminator audio)
If you are using usbradio.conf, you will want to run radio-tune-menu option 2 (Auto-Detect Rx Noise Level Value (with no carrier) --- when you connect it to the radio, etc... maybe it's picking up some noise/signal somehow... I've never had the dsp option in usbradio.conf trigger anything like that without a radio connected, is this in a high RF environment maybe?
I assume your usbradio.conf file looks like this:
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=67.0
rxctcssfreqs=162.2
txctcssfreqs=67.0
;rxctcssoverride=0
carrierfrom=dsp
ctcssfrom=dsp
rxdemod=flat
txprelim=yes
txlimonly=no
plfilter=yes
txtoctype=notone
txmixa=composite
txmixb=no
invertptt=0
duplex=1
rxondelay=0
Mark
**** North West Hub Allstar Node 2295 ****
"Got Root?"
How many software engineers does it take to change a light bulb? None. It's a hardware problem.
The best way to accelerate a computer running Windows is at 9.81 m/s².
"I get paid to support Windows, I use Linux to get work done."
On Sun, Feb 18, 2018 at 7:27 PM, ARS W5OMR <ars.w5omr@gmail.com> wrote:
I'm at my wit's end... Somewhere between asterisk -Rcvvvv and modules.conf and 'usbradio.conf ... ARRRHGGG!
I know, you've been there, too - I've not had this stuff up and running for over 3 years, I've forgotten some of the most important things I knew... Steve/N4IRS, great guy that he is, helped me tremendously the other day and all was 'ok'. It wasn't quite done, but at the time, I felt confident it was merely minor tweeking... I still had to make an interface cable for the repeater to the URIx but, even without a radio connected, I was connecting (monitor mode) to other nodes. That was cool! It was PROGRESS! But, the red LED on the URI stayed on. Even though there wasn't a radio connected, I knew it wasn't supposed to be on. That meant it was sending the 'xmit' signal out. Hell, even in the node status, it's saying it's timing out and I don't know where else to tell allstar that it's not even receiving a signal. First thing I did, was modify usbradio.conf and inverted PTT and that shut it off. The voltage on the output of the URI (Pins 1 (PTT) and 13 (GND)) 'floats' somewhere around 0.65 to 0.72v, but when it's transmitting, it is pulled DOWN to 0v. That's opposite of inverting PTT from 0 to 1. (head scratch)
This is on a Raspberry Pi3 connecting to a Motorola R100 repeater.
Here are the .conf files, if someone wouldn't mind having a gander....
iax.conf ----------
; Inter-Asterisk eXchange driver definition ; http://docs.allstarlink.org/drupal/node/15
; ulaw, alaw, GSM and ADPCM should only be used, ; the rest of the standard Asterisk codecs ; (speex, ilbc, lpc10, etc) should be avoided.
; The ulaw and alaw codecs have the best audio quality, ; followed by ADPCM, and lastly GSM, ; Bandwidth used is in the reverse order to audio quality. ; GSM uses the least bandwidth, and alaw/ulaw the most.
; CODEC AUDIO QUALITY BANDWIDTH (including IP and Ethernet headers) ; ULAW best 87 kbps ; ADPCM good 55 kbps ; GSM mediocre 36 kbps
[general] bindport = 4569 ; bindport and bindaddr may be specified ; NOTE: bindport must be specified BEFORE ; bindaddr or may be specified on a specific ; bindaddr if followed by colon and port ; (e.g. bindaddr=192.168.0.1:4569)
; bindaddr = 192.168.0.1 ; more than once to bind to multiple ; addresses, but the first will be the ; default
disallow = all ; The permitted codecs for outgoing connections ; Audio Quality Bandwidth allow = ulaw ; best 87 kbps allow = adpcm ; good 55 kbps allow = gsm ; medicore 36 kbps
jitterbuffer = yes forcejitterbuffer = yes dropcount = 2 maxjitterbuffer = 4000 maxjitterinterps = 10 resyncthreshold = 1000 maxexcessbuffer = 80 minexcessbuffer = 10 jittershrinkrate = 1 tos = 0x1E autokill = yes delayreject = yes ; iaxthreadcount = 30 ; iaxmaxthreadcount = 150
register = 29655:xxxxx@register.allstarlink.org ; This must be changed to your node number, password ; remove the leading ";"
; Incoming radio connections
[radio] type = user disallow = all allow = ulaw allow = adpcm allow = gsm
codecpriority = host context = radio-secure transfer = no
[iaxrpt] ; Connect from iaxrpt Username field (PC AllStar Client) type = user ; Notice type is user here <--------------- context = iaxrpt ; Context to jump to in extensions.conf auth = md5 secret = Your_Secret_Pasword_Here host = dynamic disallow = all allow = ulaw allow = adpcm allow = gsm transfer = no
[iaxclient] ; Connect from iax client (Zoiper...) type = friend ; Notice type here is friend <-------------- context = iax-client ; Context to jump to in extensions.conf auth = md5 secret = Your_Secret_Password_Here host = dynamic disallow = all allow = ulaw allow = adpcm allow = gsm transfer = no
[allstar-sys] type = user context = allstar-sys auth = rsa inkeys = allstar disallow = all allow = ulaw
[allstar-public] type = user context = allstar-public auth = md5 secret = allstar disallow = all allow = ulaw allow = gsm
; The following should be un-commented to support Allstar Autopatch service ; [allstar-autopatch] ; type = peer ; host = register.allstarlink.org ; username = <One of the Node numbers on this server> ; secret = <The node password for the above node> ; auth = md5 ; disallow = all ; allow = ulaw ; transfer = no ======================================
rpt.conf --------- ; Radio Repeater configuration file (for use with app_rpt)
; Your Repeater
[29655] ; Change this to your assigned node number
; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza
; Enable the selected channel driver in modules.conf !!! ; rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA rxchannel = Radio/usb_29655 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional)
linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db.
erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects
;controlstates = controlstates ; system control state stanza
scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza
telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza
context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional)
hangtime = 1000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 1000 ; longer squelch tail totime = 300000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)
idrecording = |iW5OMR/R ; id recording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iW5OMR ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)
unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).
;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them)
;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.
;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left.
;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60)
;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.
holdofftelem = 1 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node.
telemdefault = 1 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter.
telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1)
;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)
parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command
parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received
;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option
startup_macro=*982 ; Macro to run at startup (optional)
nodenames = /var/lib/asterisk/sounds/rpt/nodenames ; Point to nodename sound directory
; *** Status Reporting ***
; Uncomment either group following two statpost lines to report the status of your node to stats.allstarlink.org ; depending on whether you are running ACID, Debian or Limey Linux. ; The difference is simply where your wget is located.
; ** For ACID and Debian *** statpost_program = /usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
; ** For Limey Linux ** ;statpost_program = /bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null ;statpost_url = http://stats.allstarlink.org/uhandler.php ; Status updates
[functions]
; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions
; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions
; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91
1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only)
; End Mandatory Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands 5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands
61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down
; autopatchup can optionally take comma delimited setting=value pairs:
; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only)
721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only
; ilink commands 1 through 5 are defined in the Mandatory Command section
806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes ; *** I'll change this later - just noticed it ge/omr *** 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control operator (cop) functions. Change these to something other than these codes listed below!
901 = cop,1 ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable
904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only)
907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable
909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable
911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable
913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state
915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable
917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable
919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime)
921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush)
924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 930 = cop,30 ; Recall Memory Setting in Attached Xcvr
931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr
932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed
933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand
936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand
942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign
945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag
948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)
949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd)
951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled
956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable
958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable
960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only)
982 = playback,rpt/node_enabled ; Report node enabled to transmitter
[functions-remote]
0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key
[telemetry]
; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ;
ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated
; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1
; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.
; Morse code parameters, these are common to all repeaters.
[morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude
; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ;
[wait-times] telemwait = 1000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 500 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 500 ; Time to wait before announcing "call terminated"
; ; This is where you define your nodes which cam be connected to. ;
[nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here.
29655 = radio@127.0.0.1:4569/29655,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases
[memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m
; Place command macros here
[macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060#
; Data Acquisition configuration
;[daq-list] ;device = device_name1 ;device = device_name2
;Where: device_name1 and device_name2 are stanzas you define in this file
;device = daq-cham-1
; Device name
;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out
;[meter-faces]
;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,?
;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation
; Scheduler - execute a macro at a given time
[schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2.
==============================================
echolink.conf (not that I think -this- part matters much)
[el0] call = W5OMR/R ; Change this! pwd = xxxxx ; Change this! name = Geoff ; Change this! qth = Splendora ; Change this! email = INVALID ; Change this! node = 004817 ; Change this! ; Data for EchoLink Status Page lat = 0.0 ; Latitude in decimal degrees lon = 0.0 ; Longitude in decimal degrees freq = 0.0 ; not mandatory Frequency in MHz tone = 0.0 ; not mandatory CTCSS Tone (0 for none) power = 5 ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts) height = 2 ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet) gain = 9 ; Gain in db (0-9) dir = 0 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction)
maxstns = 5 ; Max Stations
rtcptimeout = 10 recfile = /tmp/echolink_recorded.gsm ; astnode = 29655 ; Change this! context = radio-secure ; Default in code is echolink-in
; Max 3 servers server1 = nasouth.echolink.org server2 = naeast.echolink.org server3 = server3.echolink.org
; To deny w6xxx you would add the statement: deny = w6xxx ; To prohibit computer-based connections you would write: permit = *-* ; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
; permit ; comma delimited list of callsign, type (-r) ; deny
; Remote text commands thru netcat: ; o.conip <IPaddress> (request a connect) ; o.dconip <IPaddress> (request a disconnect) ; o.rec (turn on/off recording)
; ipaddr ; port
===============================
So, does anything 'jump out' at ya?
--
73 = Best Regards, -Geoff/W5OMR _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- Operating your AM rig without a scope is like driving our car at night without headlights. (~K4KYV) 73 = Best Regards, -Geoff/W5OMR