Lu You make the change to the file, save it and then go to the Linux command line (usually in the source directory above) and type make you will see a number of lines scroll by followed by: make[1]: Leaving directory `/usr/src/astsrc/asterisk/main' +--------- Asterisk Build Complete --------- + Asterisk has successfully been built, and + can be installed by running: + + make install +-------------------------------------------+ So then you type make install and again a bunch of stuff scrolls by, ending with +---- Asterisk Installation Complete -------+ + + YOU MUST READ THE SECURITY DOCUMENT + + Asterisk has successfully been installed. + If you would like to install the sample + configuration files (overwriting any + existing config files), run: + + make samples + +----------------- or --------------------- + + You can go ahead and install the asterisk + program documentation now or later run: +\ + + make progdocs + + **Note** This requires that you have + doxygen installed on your local system +------------------------------------------- The you type astres.sh And you are good to go Merry Christmas Ken From: Lu Vencl [mailto:vencl@att.net] Sent: Saturday, December 24, 2011 11:20 PM To: 'Ken'; 'Jim Duuuude'; w7ry@centurytel.net; 'app_rpt mailing list' Subject: RE: [App_rpt-users] CTCSS Drop Out Time Yeap, I was the one that brought that up several months ago, but I never could figure out how to "make / make install" . I have no clue what that means.. If someone could help me out with that, I will finally get this to 1200 MS which will cover my Yasue radios. Thanks! KA4EPS From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Ken Sent: Saturday, December 24, 2011 9:02 PM To: 'Jim Duuuude'; w7ry@centurytel.net; 'app_rpt mailing list' Subject: Re: [App_rpt-users] CTCSS Drop Out Time Notone AKA chicken burst gives you carrier with no tone at the end. But some radios are too slow in closing the CTCSS and still make noise. There was a posting on here a while back that pointed the time delay in: /usr/src/asterisk/asterisk/channels/xpmr/xpmr.h The default is 600 ms. Some radios might be slower than this. You could change (increase) it, then make / make install and restart asterisk. My Alinco DR-?35 series seem to want to give you a small squelch tail no matter what you do, however. 73 Ken From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Jim Duuuude Sent: Saturday, December 24, 2011 6:17 PM To: w7ry@centurytel.net; app_rpt mailing list Subject: Re: [App_rpt-users] CTCSS Drop Out Time try txtoctype = notone in usbradio.conf JIM WB6NIL _____ From: w7ry@centurytel.net To: app_rpt-users@ohnosec.org Date: Sat, 24 Dec 2011 13:55:51 -0800 Subject: [App_rpt-users] CTCSS Drop Out Time Anyone know if there is an adjustment of the time the transmitter stays keyed, and the PL tone drops out and where that setting is? With my rigs, I still here the squelch crash after the repeater drops out. I would like to cut the PL off a little sooner or delay the transmitter a little longer. BTW, I'm all up and running with the repeater function and the node! Thanks to all that helped me get past the learning curve! Thanks! Merry Christmas 73 Jim W7RY _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users