10 Feb
2014
10 Feb
'14
4:33 p.m.
Hay Guys; You have to excuse andy's comment, he's a newbee tech and has little experience in these matters...... JK -------------------------------------------- On Sun, 2/9/14, Andrew Sylthe <asylthe@kc9ona.com> wrote: Subject: Re: [App_rpt-users] app_rpt parallel port usage To: "mike@midnighteng.com" <mike@midnighteng.com> Cc: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Date: Sunday, February 9, 2014, 12:33 AM Dude! You guys are fucking hardware pimps!!! Allstar is the the shit, and thanks for writing such bitching software! On Saturday, February 8, 2014, <mike@midnighteng.com> wrote: Here is a page that explains parallel port usage for acid. http://themidnightengineer.com/category/ham-amateur-radio/app_rpt/connecting-radios/ -------- Original Message -------- Subject: Re: [App_rpt-users] Allstar parallel port (was source of USB CM108 FOBs - CHEAP) From: Jim W7RY <w7ry@centurytel.net> Date: Sat, February 08, 2014 9:49 pm To: app_rpt-users@ohnosec.org I already know how to build a simple transistor switch.... How do you set up Asterisk to use the parallel port? What commands where? 73 Jim W7RY On 2/8/2014 1:34 PM, K&R Yoksh wrote: > Hello Andrew, > > In case George doesn't have anything written up for parallel port > operation: > http://www.qsl.net/k0kn/plri.html > > There are several circuits detailed here, from the simplest discrete > transistor type, to a transistor IC type that can support multiple > radios. > > You can also use an off-the-shelf IRLP board, should you have one > laying around. The DTMF decoder is not supported by Asterisk (Asterisk > uses DSP techniques to decode DTMF), so I dropped the MT8870 from my > schematics. > > At it's simplest, all you'd really need is one NPN transistor for PTT > (active high from parallel port, active low to activate PTT), and one > PNP transistor for COS (if active high from radio). If your radio uses > active low COS, I'd buffer with two transistors (PNP to NPN), rather > than directly connecting the radio to the PC. > > I'd suggest using active low at the parallel port inputs. > > 73 and good luck. > > Kyle > K0KN > Allstar 2210-2219 > > > --- Original Message --- > > Hello George, > > Do you have it documented anywhere how you configure the parallel port > for > COR and PTT? I'd love to see how you have it configured? > > Thanks! > > On Saturday, February 8, 2014, George Csahanin <george@dyb.com> wrote: > >> I bought some CM108 fobs on EBAY for $0.99 each. He has a s***load of >> them. Not knowing if they'd be real CM108 I waited till I got them to >> send >> this note. The USB ID is 08dc:000c the real thing. >> >> The last four nodes I built up use D945 motherboards which have parallel >> ports, which I use for COS/PTT and the USB fob only does audio. No >> need to >> modify them for PTT and COS, etc. >> >> Anyhow, the EBAY auction is 300503465055 OR click this >> link<http://www.ebay.com/itm/300503465055?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649> >> >> Seller's store is circle607. They're in Hong Kong. But the postage was >> under $1.20 for all ten. >> >> I stocked up simply because they work so well, cost so little, and not >> sure when they will stop being available. (hoarding 101) >> >> GeorgeC >> W2DB >> Allstar 2360 > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users@ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > down to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to the list detailing the problem. > _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- Andrew Sylthe KC9ONA Cell: 224.623.3853 -----Inline Attachment Follows----- _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.