are you using the current sources from SVN? From: monty@ke7jvx.com Date: Fri, 16 Dec 2011 11:55:17 -0700 To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Low Band Remote Base Been working off list with David on this issue. Tried the manual split in the memory channel: 06 = 53.720,136.5,1000,h-t Still will only do a 0.5 mhz split, even tried 2000 just to make sure. In Checking the source, it looks like that only applies to Kenwood radios in 2m/70cm. My question is could this capability be added to accommodate the low band Syntors with the Xcat? Monty On Sat, Dec 10, 2011 at 9:42 PM, David KE6UPI <dshaw@ke6upi.com> wrote: it does look like 2/70 and kenwood only. David On Fri, Dec 9, 2011 at 8:42 PM, Monty <monty@ke7jvx.com> wrote: I searched app_rpt.c and found this: static int setkenwood(struct rpt *myrpt) { char rxstr[RAD_SERIAL_BUFLEN],txstr[RAD_SERIAL_BUFLEN],freq[20]; char mhz[MAXREMSTR],offset[20],band,decimals[MAXREMSTR],band1,band2; int myrxpl,mysplit,step; int offsets[] = {0,2,1}; int powers[] = {2,1,0}; if (sendrxkenwood(myrpt,"VMC 0,0\r",rxstr,"VMC") < 0) return -1; split_freq(mhz, decimals, myrpt->freq); mysplit = myrpt->splitkhz; if (atoi(mhz) > 400) { band = '6'; band1 = '1'; band2 = '5'; if (!mysplit) mysplit = myrpt->p.default_split_70cm; } else { band = '2'; band1 = '0'; band2 = '2'; if (!mysplit) mysplit = myrpt->p.default_split_2m; } Looks to be only for 2m and 70cm. Monty On Fri, Dec 9, 2011 at 2:50 PM, David KE6UPI <dshaw@ke6upi.com> wrote: You can check the code (app_rpt.c) and see if there. I bet it is. I don't think Jim would have limit for just 2m/70cm bands. David On Fri, Dec 9, 2011 at 12:03 PM, Monty <monty@ke7jvx.com> wrote: I know in the config program there is a split that is set, so I might have to play with that. From the webpage you referenced it looks to be only for 2m and 440. Monty On Fri, Dec 9, 2011 at 8:44 AM, David KE6UPI <dshaw@ke6upi.com> wrote: Hello Monty, Sorry I don't know to much about your hardware. I do know that the offset works on my TM-G707 kenwood. Could it be a Syntor problem? David On Wed, Dec 7, 2011 at 8:02 PM, Monty <monty@ke7jvx.com> wrote: Hey David, Thanks for your response. I tried this: 06 = 53.720,136.5,1000,h-t When I call it up, it still splits to 0.5 mhz (53.220). Made sure I rebooted the node as well. So for grins I tried this: 06 = 53.720,136.5,2000,h-t Still it transmits at 53.220 instead of 52.720. Monty On Wed, Dec 7, 2011 at 9:26 AM, David KE6UPI <dshaw@ke6upi.com> wrote: Check out this webpage.http://ohnosec.org/drupal/node/175 You may also specify the offset in a memory channel by adding an additional parameter before the options, for example: 01 = 147.435,103.5,1035,h-t ; This would be for W6NUT in Los Angeles with input of 146.40 David On Sun, Dec 4, 2011 at 2:37 PM, Monty <monty@ke7jvx.com> wrote: Hello Everyone, I have successfully integrated a Low Band Syntor X with an Xcat to app_rpt using CI-V. I have a problem though. There are currently 6 6m repeaters here in Arizona, 3 have 0.5 mhz split and the other 3 have 1 mhz splits. I have only been successful in programing the 0.5 split frequencies in App_Rpt memories. Is there a trick to make it split to 1 mhz or is that not possible? Monty _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users