do a 'dmesg | grep usb' and you'll ge this: usbcore: registered new driver usbfs usbcore: registered new driver hub usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usb usb1: configuration #1 chosen from 1 choice usb usb2: configuration #1 chosen from 1 choice usb usb3: configuration #1 chosen from 1 choice usb usb4: configuration #1 chosen from 1 choice usb usb5: configuration #1 chosen from 1 choice usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice input: USB HID v1.00 Device [C-Media Electronics Inc. USB PnP Sound Device] on usb-0000:00:1d.1-1 usbcore: registered new driver snd-usb-audio Notice the usb 3-1 before the C-Media Electronic Inc. device.... That's the address of your URI In your usbradio_tune_usb0.conf file make sure you match the new devices port address to this listed below: [usb0] ; name=usb0 ; devicenum=0 devstr=3-1 <============== Make sure it has the port address of the new port you plugged it in to rxmixerset=438 txmixaset=407 txmixbset=0 rxvoiceadj=1.263154 rxctcssadj=2.154079 txctcssadj=199 rxsquelchadj=900 restart asterisk.... If you don't get the device address right, all your tuning parameters will be thrown off as well. _______________________________ Paul Agamata Sysman@Xceptions.COM ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of REDBUTTON_CTRL [jrorke@cogeco.ca] Sent: Sunday, July 17, 2011 1:21 AM To: APP_RPT_Users Subject: Re: [App_rpt-users] Moving URI between USB ports. Hi Michael, I tried a PCI 4 port USB card and didn't have much luck with it. Not to say they don't work, but I never got it to work properly. I did make sure that it was USB 2.0. You might want to try to make a small adjustment to your radio tune file like bumping the squelch setting by 1 notch, then re-saving. That will update your radio tune file with the current USB port. As example, if your squelch was set to 850 do a "radio tune rxsquelch 851" Then save with "radio tune save". Perhaps restart Asterisk and see if that works. I have always relied on PCs that are P4 3G boxes that have 4 - 6 USB 2.0 ports on board and have had no trouble there. What is the speed of your box? Does it meet the min specs? USB ports must be 2.0 or you will have problems. Regards, Jon VA3RQ On 7/17/2011 3:23 AM, Michael Carey wrote:
Hi Everybody,
In an attempt to fix a random "motorboating" audio issue on transmit I have with my new AllStarLink node, I fitted a PCI USB2.0 board (NEC chipset) to the computer. CentOS found the new card fine. I shifted my URI to one of the new USB ports and everything seems to be working... EXCEPT I am not getting any transmitted audio. Receive audio is fine, the radio will key up OK... but I get no telemetry tones nor any incoming audio.
What needs to be done when you move a URI to another USB port? Why would receive audio be fine and transmitted audio not?
Please be gentle, I am still a little green with this new stuff.
Michael. VK5ZEA _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users