Hello Mike, This is good information. I looked at dmesg and saw there are 3 USB HUBs (6 ports total: 2 on the side, 3 on the back and 1 internal). I am using the Asus Eee All In One machines. I got a bunch of them free because the touchscreen went out. These were pulls as old POSs (Point of Sale, not the other POS) lol These machines are great onsite for me because I dont need anything extra other than a USB KB. I have the two URIs on the back of the machine and seems to be on the same hub. I will make it out to the site and move one to the side and check it is on another hub. Hopefully this will solve my TX problem. Thanks for the input. boB - W5EVH On Mon, Feb 10, 2014 at 1:42 PM, <mike@midnighteng.com> wrote:
From my own experience, (i have a bunch of hardware experience)
I would say the best place to look first is the PNP interrupt assignment even though you can't force PNP to shuffle IRQ's on most boards anymore you can eliminate unused built in hardware to alleviate the stress.
Mainly some other hardware in your system is sharing a IRQ with the USB HUB and intercepting info that was not intended for it. If using a machine with PS2 style mouse, unplug the mouse.
Some other things to try is to NOT plug more than one USB FOB (or any USB device) into a single USB HUB. This may confuse you a bit but if you have 6 USB ports built in than you have 3 USB HUBS normally each HUB is 2 ports.
If all fails, reset the bios to factory, "reboot", set bios again without unneeded hardware (ie serial, parallel and unused USB when possible), "reboot machine again" and see where you are. Don't forget to save settings each time.
Sharing IRQ's in a system was not a bad idea but it only takes one piece of hardware to not comply correctly to screw things up.
It is always a benefit to check the hardware before tweeking any software. Let me know if you get anywhere on this.
...mike/kb8jnm
-------- Original Message -------- Subject: Re: [App_rpt-users] Loosing TX From: Bob Roszkowski <bob@w5evh.org> Date: Mon, February 10, 2014 2:20 pm To: Michael Hebert <mhebert1975@gmail.com>, app_rpt mailing list <app_rpt-users@ohnosec.org>
Hi Michael,
Thanks for the information to test the URI. It does not seem the URI is the issue. I have swapped the URIs with new ones and they all did the same thing.
I believe this issue is with the PC hardware or software. Might be a USB bus problem. I will look further into it.
boB - W5EVH
On Fri, Feb 7, 2014 at 7:45 PM, Michael Hebert <mhebert1975@gmail.com>wrote:
You can try the uridiag program.
Q: How can I test my URI? A: Download the uridiag program located at
http://svn.ohnosec.org/viewvc/projects/allstar/uridiag/trunk/?root=svn&view=...
Un-tar it and then 'make' it. Run ./uridiag and select option C. That will tell you how to make a loop-back connector for running the diagnostics. This is the same program we use to test each URI before it leaves the factory.
Q: How can I make a loop-back cable to test my URI? A: Get a male DB-25 connector such as L717SDB25P from www.digikey.com . Then wire up the following connections: Pin 1 to Pin 7 Pin 2 to Pin 3 Pin 4 to Pin 8 Pin 23 to Pin 24 10K Resistor between Pins 21 and 22 10K Resistor between Pins 21 and 23 For URIx (CM119) only, also include the following connections: Pin 5 to Pin 10 Pin 6 to Pin 11
On Fri, Feb 7, 2014 at 3:22 PM, Bob Roszkowski <bob@w5evh.org> wrote:
Group,
I have a site that is acting strange. I have a server with a VHF(Mastr II) and UHF(TKR-850) repeater, each with a URI. Both repeaters are linked together locally. I noticed while someone is using the machine, the TX will just stop while they are talking. If I switch to the other repeater, the TX is working fine. The URIs Red LED goes out. This happens to both machines. I have swapped and changed URIs and cables with no change. Any ideas?
boB - W5EVH
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.