As requested rpt.conf: [1999] ; Name of First Repeater rxchannel = Zap/1 ; Rx audio/signalling channel ; Note: if you use a unified interface (tx/rx on one channel), only ; specify the rxchannel and the txchannel will be assumed from the rxchannel functions=functions ; Repeater Function Table ; ; Added phone_functions=phone_functions ; phone_functions = phone_functions ;phone functions table link_functions=link-functions ; Link Function Table telemetry=telemetry ; Telemetry descriptions wait_times=wait-times ; Wait times context = radio ; dialing context for phone callerid = "Your Repeater" <6198192562> ; callerid for phone calls idrecording = /etc/asterisk/id ; id recording accountcode=RADIO ; account code (optional) hangtime=1000 ; squelch tail hang time (in ms) (optional) totime=90000 ; transmit time-out time (in ms) (optional) idtime=180000 ; id interval time (in ms) (optional) ; ;Added duplex=2 ; ;duplex=2 ; The default values for hangtime, time-out time, and id interval time are ; 5 seconds (5000 ms), 3 minutes (180000 ms), and 5 minutes (300000 ms) ; respectively politeid=30000 ; time in milliseconds before ID timer ; expires to try and ID in the tail. ; (optional, default is 30000). idtalkover=|iid/r ; Talkover ID (optional) default is none unlinkedct=ct2 ; unlinked courtesy tone (optional) default is none ; ; Repeater function table for node 010 ; [functions] 1=ilink,1 ; Specific link disconnect 2=ilink,2 ; Specific Link connect - monitor only 3=ilink,3 ; Specific Link connect - transceive 4=ilink,4 ; Enter command mode on a specific link 7=ilink,5 ; Link status 80=status,1 ; System info 81=status,2 ; Time 82=status,3 ; app_rpt.c Version 6=autopatchup ; Autopatch up 0=autopatchdn ; Autopatch down ; ;Added cop,6 in this context just to see if it would recognize cop,6 ; 88=cop,6 ; PTT Radio 99=cop,4 ; Audio test tone ; ;Added phone_functions table for the phone_functions=phone_functions ; [phone_functions] 1=ilink,1 ; Specific link disconnect 2=ilink,2 ; Specific Link connect - monitor only 3=ilink,3 ; Specific Link connect - transceive 4=ilink,4 ; Enter command mode on a specific link 7=ilink,5 ; Link status 80=status,1 ; System info 81=status,2 ; Time 82=status,3 ; app_rpt.c Version ; ;Added cop,1 - cop,6 for testing purposes. ; 84=cop,1 ;warm boot 85=cop,2 ;system enable 86=cop,3 ;system disable 87=cop,5 ;debug mode 88=cop,6 ;system PTT 6=autopatchup ; Autopatch up 0=autopatchdn ; Autopatch down 99=cop,4 ; Audio test tone ; ; Link function table ; ; If this section is defined, then the remote user accessing our machine in command mode ; will only be able to do the functions defined in this section. If this section is ; omitted, then the link functions will be the same as the repeater functions. ; [link-functions] 1=ilink,1 ; Specific link disconnect 2=ilink,2 ; Specific Link connect - monitor only 3=ilink,3 ; Specific Link connect - transceive 7=ilink,5 ; Link status 80=status,1 ; System info 81=status,2 ; Time 82=status,3 ; app_rpt.c Version 6=autopatchup ; Autopatch up 0=autopatchdn ; Autopatch down 84=cop,1 ;warm boot 85=cop,2 ;system enable 86=cop,3 ;system disable 87=cop,5 ;debug mode 88=cop,6 ;system PTT 99=cop,4 ; Audio test tone [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(660,880,150,2048) ct3=|t(440,0,150,2048) ct4=|t(550,0,150,2048) ct5=|t(660,0,150,2048) ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(700,1100,150,2048) remotetx=|t(1633,0,75,2048)(0,0,75,0)(1209,0,75,2048); remotemon=|t(1209,0,75,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) ; ; Morse code parameters, these are common to all repeaters. ; [morse] speed=20 ; Approximate speed in WPM frequency=800 ; Morse Telemetry Frequency amplitude=4096 ; Morse Telemetry Amplitude idfrequency=1064 ; Morse ID Frequency idamplitude=3072 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait=1750 ; Time to wait before sending most telemetry idwait=500 ; Time to wait before starting ID unkeywait=1000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait=1500 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] 1999 = radio@127.0.0.1/1999 ; This must be changed to your IP address We added cop,6 to the regular functions table and the link functions table just to test and see if it was picking up only those functions instead, since there was a comment that if link functions were enabled then the remote user would only have access to them. Here is the extensions.conf for connecting to the radio: exten => 305,1,Rpt,1999|P ulaw is allowed in both IAX.conf and SIP.conf that we are using to dial the radio. Does this need to be changed as well? Trying to add as much info I can think of. Thanks, JRH
hwstar@rodgers.sdcoxmail.com 03/15/06 2:57 PM >>> It probably would be a good idea to attach your rpt.conf file to the thread.
Steve WA6ZFT
From: "James Harfield" <harfija@auburn.edu> Date: 2006/03/15 Wed PM 12:29:28 PST To: <app_rpt@lists.illiana.net> Subject: Re: [App_rpt] COP Functions
That's what I figure as well. I've tried Softphone, Cell phone, land
phone. All the default ilink and status functions work, along with cop,4 to initiate the test tone. But cop,6 won't key the radio.
telesistant@hotmail.com 3/15/2006 2:21 PM >>> Well, if you have cop,6 defined as *88, and you are comming in with
the P
option, and you have phone_functions = phone_functions, then you definitely should be able to key the radio from the phone by dialing *88 (from the phone and only from the phone).
Jim, WB6NIL
From: "James Harfield" <harfija@auburn.edu> Reply-To: Asterisk Repeater Controler <app_rpt@lists.illiana.net> To: <app_rpt@lists.illiana.net> Subject: [App_rpt] COP Functions Date: Wed, 15 Mar 2006 13:11:02 -0600 MIME-Version: 1.0 Received: from lists.illiana.net ([207.227.243.140]) by bay0-mc12-f14.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.1830); Wed, 15 Mar 2006 11:12:02 -0800 Received: (qmail 25119 invoked from network); 15 Mar 2006 19:12:00 -0000 Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP; 15 Mar 2006 19:12:00 -0000 Received: (qmail 25092 invoked from network); 15 Mar 2006 19:11:52 -0000 Received: from d1.duc.auburn.edu (131.204.2.2)by 0 with SMTP; 15 Mar 2006 19:11:52 -0000 Received: from TMIA1.AUBURN.EDU (tmia1.auburn.edu [131.204.3.30])by d1.duc.auburn.edu (8.13.4/8.13.4) with ESMTP id k2FJBjbE013830for <app_rpt@lists.illiana.net>; Wed, 15 Mar 2006 13:11:49 -0600 (CST) Received: from zTMIA1-MTA by TMIA1.AUBURN.EDUwith Novell_GroupWise; Wed, 15 Mar 2006 13:11:45 -0600 X-Message-Info: 6sSXyD95QpVMWPCRYsLAxQFjIgPjv7anT7L4spyjmhA= Return-Path: <harfija@auburn.edu> Delivered-To: mailman-app_rpt@lists.illiana.net X-Mailer: Novell GroupWise Internet Agent 7.0 X-BeenThere: app_rpt@lists.illiana.net X-Mailman-Version: 2.1.6 Precedence: list List-Id: Asterisk Repeater Controler <app_rpt.lists.illiana.net> List-Unsubscribe:
List-Archive: <http://lists.illiana.net/pipermail/app_rpt> List-Post: <mailto:app_rpt@lists.illiana.net> List-Help: <mailto:app_rpt-request@lists.illiana.net?subject=help> List-Subscribe:
Errors-To: app_rpt-bounces@lists.illiana.net X-OriginalArrivalTime: 15 Mar 2006 19:12:03.0471 (UTC) FILETIME=[57DDA1F0:01C64864]
I'm having a problem getting cop,6 to function correctly in PTT'ing the radio.
I have phone_functions = phone_functions defined in rpt.conf and within the phone_functions heading I have: 88 = cop,6 defined with the other cop, ilink, and status functions. When connecting to my base I use the |P option instead of |D for phone control.
The problem I'm having is that cop,6 will not activate the base to transmit. All the status commands, System Info, Time, Version, and the test tone cop,4 command work fine. The radio keys up, the appropriate information is sent, and the radio is unkeyed. But cop,6 will not key it. What I can do is manually key the radio and then use *88 (for cop,6) to talk and # when I want to end talking. I've tried to dig through the code and look at the difference between cop,6 and cop,4 for activating the base, but I'm quite confused as to why one can work and one cannot.
Thanks,
JRH
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt