Do you have unsquelched discriminator Rx audio running to the RTCM? 13 COR type needs to be "normal" otherwise it'll just use the PL input pin for squelch. Also I believe you won't want nodemph set in voter.conf either since discriminator audio is typically flat (FM), so audio will will need to be deemphasized in software. Jesse
On Jun 13, 2015, at 4:23 PM, R Dahl <ve6ars@gmail.com> wrote:
Hi, Ive been struggling for weeks trying to use the dsp squelch. The sql and diode calibration routine seems to work like the book says as well as setting all the rx/tx levels. The problem is when I set the squelch pot which seems to do nothing at all. It all works as I believe it should when using ext COR from the radio. Repeat and echolink and offline functions all work. It seems odd(to me) that the sql pot setting always returns zero. Main and status displays are below, followed by voter.conf Any suggestions? Ross
1 - Serial # (1234) (which is MAC ADDR 00:04:A3:00:04:D2) 2 - VOTER Server Address (FQDN) (10.0.0.140) 3 - VOTER Server Port (667), 4 - Local Port (Override) (0) 5 - Client Password (xxxx), 6 - Host Password (xxxx) 7 - Tx Buffer Length (3000) 8 - GPS Data Protocol (0=NMEA, 1=TSIP) (0) 9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0) 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2) 11 - GPS Baud Rate (4800) 12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (2) 13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1) 14 - Debug Level (0) 15 - Alt. VOTER Server Address (FQDN) () 16 - Alt. VOTER Server Port (Override) (0) 17 - DSP/BEW Mode NOT SUPPORTED 18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0) 19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC) 20 - Ext. CTCSS Input Threshold (850) (0-1023) 97 - RX Level, 98 - Status, 99 - Save Values to EEPROM i - IP Parameters menu, o - Offline Mode Parameters menu q - Disconnect Remote Console Session, r - reboot system, d - diagnostics
Enter Selection (1-20,97-99,r,q,d) :
----98---- S/W Version: 1.46 03/04/2014 System Uptime: 15834.4 Secs IP Address: 10.0.0.134 Netmask: 255.255.255.0 Gateway: 10.0.0.1 Primary DNS: 10.0.0.1 Secondary DNS: 8.8.4.4 DHCP: 1 VOTER Server IP: 10.0.0.140 VOTER Server UDP Port: 667 OUR UDP Port: 667 GPS Lock: 0 Connected: 1 COR: 1 EXT CTCSS IN: 1 PTT: 0 RSSI: 255 Current Samples / Sec.: 0 Current Peak Audio Level: 58800 Squelch Noise Gain Value: 14, Diode Cal. Value: 43, SQL pot 0
Press The Any Key (Enter) To Continue
----voter.conf--- [general] port = 667 buflen = 500 password = xxxx
[40526] 40526 = xxxx,nodeemp,transmit,mulaw
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.