Probably not (lets hope!)....It's worthwhile to test the URI GPIO pins with a voltmeter/multimeter before proceeding! Check the voltage to ground, and flip the logic bit back and forth a few times in software. 73, David KB4FXC On Mon, 4 Jun 2018, Scott Weis wrote:
Hopefully I didn't blow anything up...
-----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of David McGough Sent: Monday, June 4, 2018 12:05 AM To: Users of Asterisk app_rpt <app_rpt-users@lists.allstarlink.org> Subject: Re: [App_rpt-users] URI GPIO Scott, The URI GPIO pins are connected to the DB-25 without any buffering, etc. They are 3.3V logic, but based on the datasheet are considered to be 5V tolerant. You'll most likely need a level converter on each GPIO pin used to drive a CDM1250 pin. A simple open-collector or open-drain transistor buffer on each used GPIO pin will work nicely. There are dozens of acceptable ways to accomplish the buffering. Here is one sample schematic using an NPN bipolar transistor and includes LED's for visual feedback. Note that this circuit inverts the logic, so logic 0 becomes 1 and vice-versa. https://hamvoip.org/docs/ptt-driver-example.png 73, David KB4FXC On Sun, 3 Jun 2018, Scott Weis wrote:
Isnââ¬â¢t the URI 5v logic?
From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Bryan Fields Sent: Sunday, June 3, 2018 7:06 PM To: Users of Asterisk app_rpt <app_rpt-users@lists.allstarlink.org> Subject: Re: [App_rpt-users] URI GPIO
Do you have a buffer from the 3.3v to 5v logic?
--
Bryan Fields
M: +1-727-409-1194
On Jun 3, 2018, at 18:27, Scott Weis <kb2ear@kb2ear.net <mailto:kb2ear@kb2ear.net> > wrote:
I'm trying to set up channel steering for a Motorola CDM1250 and have the radio working without a URI. If I ground the channel pins the channels change on the radio fine. Now when I connect the pins to a URI-x gpio1 gpio2 gpio5 and gpio6 It dosent seem to work. I have gpio1=out0 , gpio2=out0, gpio5=out0, gpio6=out0 and when I do a *584=cop,61,GPIO5=1 or *585=cop,61,GPIO5=0 nothing seems to change on the URI, either state I see +5v on the URI. Should it not get pulled to ground?
Am I doing something wrong?
Thanks & 73 de Scott KB2EAR
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.