Lu, This is for a simplex/half duplex link radio but it should be similar to what you're looking for. simpleusb.conf ; ; Usbradio channel driver Configuration File ; [general] [usb1968] ; Methodist Mountain gpio1=in hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1 carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work. txmixa=voice ; Left channel output:no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above. invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this. duplex=0 ; Full Duplex rxondelay=65 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. rpt.conf ; Radio Repeater configuration file (for use with app_rpt) ; [1968] rxchannel=SimpleUSB/usb1968 duplex=1 ;controlstates=controlstates scheduler=schedule1968 functions=functions1968 phone_functions=functions1968 ;link_functions=functions-remote ;memory = memory ;split2m = 600 ;split70cm = 5000 telemetry=telemetry callerid="K0JSC Repeater" <7193150434> accountcode=RADIO idtime=540000 ;ioport = /dev/ttyS0 ; Serial port for control ;remote = kenwood ; Radio Type ;dusbabek = yes ;authlevel = 0 ; Authorization level politeid=30000 remote_inact_timeout=1800 ; Inactivity timer for remote base nodes only (set to 0 to disable). remote_timeout=3600 ; Session time out for remote base. (set to 0 to disable) ;beaconing=0 ;idrecording = |iWZ0N/M ; id recording or morse string ;eannmode=0 ;idtalkover=|iid ; Talkover ID (optional) default is none ;nounkeyct=0 ;holdofftelem=1 ; Hold off all telemetry when signal is present on receiver or from connected nodes telemdynamic=1 nolocallinkct=1 linkunkeyct=ct5 unlinkedct=ct2 totime=180000 wait_times=wait-times erxgain=-3 etxgain=3 context=radio ;idrecording = /var/lib/asterisk/sounds/rpt/nodenames/1970 remotect=ct3 ;connpgm=yourconnectprogram ; Default: Disabled. Execute a program you specify on connect. ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm=yourdisconnectprogram ; Default: Disabled. Execute a program you specify on disconnect. ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) ;lnkactenable=0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime=1800 ; Link activity timer time in seconds. ;lnkactmacro=*52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn=30seconds ; Message to play when the link activity timer has 30 seconds left. ; althangtime=0 hangtime=0 telemdefault=2 events=events1968 ; Morse code parameters, these are common to all repeaters. [morse1968] speed=20 frequency=700 amplitude=2096 idfrequency=700 idamplitude=1500 ; [functions1968] 99=cop,6 989=cop,4 0=autopatchdn 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up 83=cop,61,GPIO1=1 *D0001=f|f|RPT_URI_GPIO1 ;door open *D0002=f|t|RPT_URI_GPIO1 ;door closed 1=ilink,1 2=ilink,2 3=ilink,3 4=ilink,4 5=macro,3 70=ilink,5 71=ilink,6 72=ilink,7 73=ilink,15 74=ilink,16 75=ilink,8 80=status,1 81=status,2 951=ilink,11 ; Permanent link disconnect 952=ilink,12 ; Permanent link receive 953=ilink,13 ; Permanent link transceive 980=status,3 ; ; [events1968] ;*D00001=f|f|RPT_URI_GPIO1 ;DOOR OPEN ;*D00002=f|t|RPT_URI_GPIO1 ;DOOR CLOSED [macro1967] 575=*C11 ; call clear wx alerts 516=*9124 ;Reboot 551 = *428299*D50# ;Start Master flip script for Normal 552 = *428299*D51# ;Start Master flip script for Net 553 = *428299*D52# ;Start Master flip script for ARES 554 = *428299*D53# ;Start Master flip script for Exercise 555 = *428299*D54# ;Start Master flip script for Skywarn 560 = *428299*D40# : Start News broadcast 586 = *82882,*41967*82882#,*41970*82882#,*41971*82882#*41974*82882# ;Send Alert Tones to all nodes ; Telemetry entries can be shared across all , repeaters or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries -freq1, freq2, duration, amplitude- ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string [telemetry] ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(660,880,150,2048) ct3=|t(440,0,150,4096) ct4=|t(550,0,150,2048) ct5=|iF ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(600,00,75,1000)(0,0,75,0)(600,0,150,1000)(0,0,75,0)(600,0,75,1000)(0,0,75,0)(600,0,75,1000) remotetx=|iK remotemon=|t(1209,0,50,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) patchup=rpt/callproceeding patchdown=rpt/callterminated ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait=2000 ; Time to wait before sending most telemetry idwait=500 ; Time to wait before starting ID unkeywait=1000 ; Time to wait after unkey before sending CTs and link telemetry calltermwait=2000 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition for ; your local nodes, and private off of allstar link nodes here. 1968 = radio@127.0.0.1/1968,NONE,y ; This must be changed to your node number #includeifexists custom/rpt.conf On Sun, Jun 7, 2015 at 12:05 PM, Lu Vencl <luvencl8@gmail.com> wrote:
Can somebody send me an example USB file on how you should configure a no that is not running off solely the discriminator processing? I am running discriminator but I am trying to use CTCSS off my repeater. It is tied to pin number seven on the URI, however no matter if I use USB or USB invert I can't seem to get the signaling straightened out. My repeater sends out 12v when CTCSS is detected. I have cor set to no. Anyone have any ideas or can provide a sample for me please?
Lu Vencl _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.