You only need 3 wires going into the transmitter. What I am talking about is pre-emphasized vs flat input audio to the radio. On the Motorola, you may have chose to use flat audio into the radio for TX, however, on the chinese radio, you only have mic audio in, so in the usbradio.conf, you have to set txprelim to no. On Mon, May 30, 2016 at 9:14 AM, Loren Tedford <lorentedford@gmail.com> wrote:
ok we are only using filtered audio at the moment we don't trust the uri to decode our tones or transmit our tones.. So that config already looks correct..
So i need PTT to GND and Audio out to the MIC on the RJ45 what about the other wires..
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com http://www.lorentedford.com http://www.kc9zhv.com http://forum.kc9zhv.com http://hub.kc9zhv.com http://www.newwavesucks.com http://forum.newwavesucks.com
On Mon, May 30, 2016 at 10:09 AM, Skyler F <electricity440@gmail.com> wrote:
Ok, first, if you are using flat TX audio on the motorola, you will have to set txprelim and txlimonly to no in the rpt.conf file.
I think the connector might be the same as a kenwood, do kenwood miss work with it, if so, this diagram may help you:
http://radioaficion.com/cms/wp-content/uploads/2015/07/Leixen_VV-898_Microph...
You are going to need to send PTT, GND, and audio out to the mic in on the RJ45 jack
On Mon, May 30, 2016 at 9:05 AM, Loren Tedford <lorentedford@gmail.com> wrote:
If I am guessing correctly I could probably take the rj45 and make it transmit the audio from the tx side of the URI 16 pin connector however kinda confused which wire needs to go where..
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com http://www.lorentedford.com http://www.kc9zhv.com http://forum.kc9zhv.com http://hub.kc9zhv.com http://www.newwavesucks.com http://forum.newwavesucks.com
On Mon, May 30, 2016 at 10:04 AM, Loren Tedford <lorentedford@gmail.com> wrote:
skyler i have a sic 2 meter transmitter at the moment i am limping it along until we get our new transmitter ordered at the moment i have a GM300 which is drifting slightly back and forth but i need the JT270M to take the place of our current transmitter so we can at least put the system in more of a stable operation
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com http://www.lorentedford.com http://www.kc9zhv.com http://forum.kc9zhv.com http://hub.kc9zhv.com http://www.newwavesucks.com http://forum.newwavesucks.com
On Mon, May 30, 2016 at 10:01 AM, Skyler F <electricity440@gmail.com> wrote:
So are you using one of the radios as a transmitter and another as a receiver? Which radio are you using for which?
73, Skyler
On Mon, May 30, 2016 at 6:11 AM, Loren Tedford <lorentedford@gmail.com
wrote:
Greetings I need pin out info on a jetstream 270m to Motorola 16 pin adapter for the transmitter and receiver the most important thing at moment is transmitter..
If possible diagrams would help me see this a little better.. We have the uricables from http://uricables.com/DuplexMotorola.html
Loren Tedford (KC9ZHV) Email: lorentedford@gmail.com Phone: 618-553-0806 Fax: 16185512755 http://www.lorentedford.com http://kc9zhv.com
Sent from Droid Turbo from Verizon wireless network
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com