Mine too, exact same situation. I have to drop the power supply on the G7 to reset it. That's not conducive to "mountain top" operation so it's still on the bench. K0JSC On Wed, Jun 12, 2013 at 12:36 PM, Kirk <wb6egr@gmail.com> wrote:
Thats not whats occuring with mine, the radio actually goes dark or stops answering the controller. Sometimes it will continue to TX/RX on the last frequency.... *2 *3 makes no differance
Sent from my piece of Crap I-Phone... I feel a Samsung 4 is in my near future
On Jun 12, 2013, at 7:44 AM, "Scott Weis" <kb2ear@kb2ear.net> wrote:
Try this, as it has been working for me for a while. ****
** **
Instead of connecting to the remote base with a *3 connect with a *2. You should be able to control the radio until the cows come home. Then do a *3 to talk on the specific channel. I have found that as soon as the radio TXs I am unable to control it any more.****
** **
Also I find the once I can’t control the G707 any more I do a *1 and disconnect then a *2 again and all is well again.****
** **
I’ve been meaning to talk to Jim about this bug.. ****
** **
Scott****
** **
*From:* app_rpt-users-bounces@ohnosec.org [mailto: app_rpt-users-bounces@ohnosec.org] *On Behalf Of *Jeff Carrier *Sent:* Wednesday, June 12, 2013 1:15 AM *To:* Monty *Cc:* app_rpt mailing list; K&R Yoksh *Subject:* Re: [App_rpt-users] G707 Remote Base Locking Up on URI****
** **
I have the same issue. First with a home brew interface so I searched hi and low for the "actual" interface board with the same issue as Kirk describes.****
De k0jsc****
On Jun 11, 2013 9:41 PM, "Monty" <monty@ke7jvx.com> wrote:****
Hi Kyle,****
** **
I fixed the syntax error, still no joy. I did have a usbradio node and the 707 on simpleusb, so I migrated the 707 to usbradio and removed all the simpleusb configs, still no joy. Any other ideas? ****
Monty****
** **
On Tue, Jun 11, 2013 at 6:42 PM, K&R Yoksh <yokshs@gmail.com> wrote:****
Hello Monty, While not specific to the remote operation, I see one thing that might make app_rpt lose it's mind.
The rxchannel parameter is very picky about syntax, especially the upper and lower case letters. The correct format is:
rxchannel=SimpleUSB/usb1010
Another thing I've learned is to never (NEVER) have usbradio.conf and simpleusb.conf exist in /etc/asterisk at the same time. This will confuse app_rpt at the least, or crash it altogether.
73,
Kyle Yoksh K0KN Olathe, KS Allstar 2210-2219 --- Original Message ---Hello Everyone,****
I have tried two Kenwood G707s with three of Jim's URI Adapter cards and two URIs on two different computers. I am able to get three or four commands (freq, pl tone, etc) then I will get Allison saying "Invalid Frequency" and the CLI shows:
"WARNING[7925]: app_rpt.c:13876 serial_remote_io: -99999 Serial device not responding on node 1010"
The radio will not steer or accept commands anymore until I power cycle the 707. The after power cycle three or four commands and will not steer again. I have tried the same computer with a VHF Syntor with an xcat and will accept every command without issue. Also one of my 707s now lives on a Quad PCI card and steers with every command without issue. Has anyone else seen this or know the remedy? Below is my rpt.conf with the URI:
[1010] archivedir=/etc/asterisk/qso rxchannel = simpleusb/usb1010 duplex=0 ioport = /dev/ttyS0 remote = kenwood authlevel = 1 memory=memory remote_inact_timeout=5400 remote_timeout=5400 functions=remote-functions phone_functions=remote-functions link_functions=remote-functions ****
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users****
** **
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users****
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users