That works with "status" commands, i.e., * 1 - Force ID (global) * 2 - Give Time of Day (global) * 3 - Give software Version (global) * 4 - Give GPS location info * 5 - Last (dtmf) user * 11 - Force ID (local only) * 12 - Give Time of Day (local only) because there are two commands defined for the time/ID functions (local or global). But the question remains how to do that with "ilink" commands, which are what do the standard "70" and "73" DTMF commands. There don't seem to be different local/global ilink commands for "system status" and "full system status". * 5 - System status * 15 - Full system status (all nodes) Maybe there's a way to "turn off" the propagation before the command and turn it back on after it's done? It would be nice to be able to get a full system status on the local node without waking everybody up that's connected. 73, Jim KH2D On 2/22/2012 8:24 AM, Bill South wrote:
Check the status values in your "functions" stanza of rpt.conf. If your "70" shows a 2 digit number beginning with a "1" it will propagate locally only, a single digit means it propagates everywhere; i.e.
my "80" is set as
80=status,11
to propagate my ID locally
but I created an "84" to propagate my ID everywhere
84=status,1
This is stated (somewhere) in the rpt.conf documentation
73, Bill, N4SV
--- On *Tue, 2/21/12, Jim Kehler /<kh2d@bellsouth.net>/* wrote:
From: Jim Kehler <kh2d@bellsouth.net> Subject: Re: [App_rpt-users] local telemetry To: app_rpt-users@ohnosec.org Date: Tuesday, February 21, 2012, 7:10 PM
Node stats (70) and full system status (73) announcements propagate to other connected nodes. I can only go three nodes deep, but if I issue those commands on any of the three, they all get the announcement.
I just checked, the time doesn't seem to do that. Which is good because it might not be the same time there as it is here :-)
73, Jim KH2D
On 2/21/2012 1:03 PM, Stephen Liggett wrote: > Maybe I am loosing my mind (you know how it gets when you are working on a project "too long" at one stretch). > > Anyway, last night I connected via my Mac to the WAN via 2125 to listen, using my web transceiver designated as W3RX. > > I then went to my HT and via the repeater, brought up that same AllStar node 2125, using the repeater's node W3YT (28325). > > All was well. I then hit the DTMF on the HT for a status report, which I assumed would send the status by LOCAL voice telemetry to the repeater node, so those listening could tell who we were connected to. To my surprise, I heard the telemetry message on the repeater AND on my web transceiver connected to the WAN. That does not seem right. I know that connect and disconnect telemetry is heard at the distant node, but I assumed that other telemetry (like status, or time) would not go further than local output to the repeater. > > Like I said, I could have been in a dazed state, but I did it twice with the same result. Is this supposed to happen? BTW, I use the AllStar/URI as a remote base input to a RC-1000v repeater controller (ie, I don't use AllStar as the controller as of now). Not sure if that matters. I just don't want the local telemetry, including some custom stuff that I have programmed, to push out distantly. > > steve > W3RX > 28325 (A) > 8676 (I) > 86768(E) > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users@ohnosec.org </mc/compose?to=App_rpt-users@ohnosec.org> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org </mc/compose?to=App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users