Ramesh, I will have to check but if I am decoding PL, how should this even begin to plan with a squelch setting? -----Original Message----- From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Ramesh Dhami (VA3UV) Sent: Sunday, October 30, 2011 7:52 AM To: 'app_rpt' Subject: Re: [App_rpt-users] cop 2 - causing PTT lock On 30/10/2011 12:01 AM, George Csahanin wrote:
When you do "rpt showvars xxxx" does it show RPT_RXKEYED=0 or 1?
I've seen this if the levels/squelch setting not being right, lower noise being received signal, etc.
<-- Hi George and all: Tried my COP2 (dtmf command) via the CLI and as Lu mentioned, that works fine, as soon as I hear RPT ENA, the PTT drops and life is good. Then I disabled the repeater and tried the dtmf command from my HT - this is what I captured on CLI: [Oct 30 07:41:31] NOTICE[19419]: app_rpt.c:7957 wait_interval: Delay complete -- <Zap/pseudo-475079875> Playing 'letters/r' (language 'en') -- <Zap/pseudo-475079875> Playing 'letters/p' (language 'en') -- <Zap/pseudo-475079875> Playing 'letters/t' (language 'en') -- <Zap/pseudo-475079875> Playing 'letters/e' (language 'en') -- <Zap/pseudo-475079875> Playing 'letters/n' (language 'en') -- <Zap/pseudo-475079875> Playing 'letters/a' (language 'en') -- Hungup 'Zap/pseudo-475079875' [Oct 30 07:41:46] NOTICE[4141]: app_rpt.c:19882 rpt: Got PL 103.5 on node 2182 -- Hungup 'Zap/pseudo-1423219721' [Oct 30 07:41:49] NOTICE[4141]: app_rpt.c:19882 rpt: Got PL 103.5 on node 2182 -- Hungup 'Zap/pseudo-1492162812' [Oct 30 07:41:52] NOTICE[4141]: app_rpt.c:19882 rpt: Got PL 103.5 on node 2182 -- Hungup 'Zap/pseudo-13915100' [Oct 30 07:41:55] NOTICE[4141]: app_rpt.c:19882 rpt: Got PL 103.5 on node 2182 -- Hungup 'Zap/pseudo-971235839' [Oct 30 07:42:04] NOTICE[4141]: app_rpt.c:19882 rpt: Got PL 103.5 on node 2182 [Oct 30 07:42:05] NOTICE[4141]: chan_usbradio.c:3010 usbradio_read: Got DTMF char * duration 127 ms [Oct 30 07:42:05] NOTICE[4141]: chan_usbradio.c:3010 usbradio_read: Got DTMF char 0 duration 84 ms [Oct 30 07:42:05] NOTICE[4141]: app_rpt.c:4288 cancel_pfxtone: cancel_pfxfone!![Oct 30 07:42:05] NOTICE[4141]: app_rpt.c:16792 channel_revert: remoterig=, nowchan=00, waschan=00 [Oct 30 07:42:05] NOTICE[19396]: app_rpt.c:10544 rpt_call: exit channel loop -- Hungup 'Zap/pseudo-895837731' [Oct 30 07:42:05] NOTICE[19396]: app_rpt.c:16792 channel_revert: remoterig=, nowchan=00, waschan=00 -- Hungup 'Zap/pseudo-2118062105' va3pmo_asterisk*CLI> Notice how I tried to key-up a few times - and no joy. Further even the end, when I sent a *0; app_rpt tells me: nowchan=00, waschan=00 So it believes that the ptt was actually off to start with. So OK, now I will bump the squelch up a bit... (Current setting was 450 with a signal level of 140) - the squelch is already kinda' high (I think?) - anyway, I bumped the squelch up to 500 - tried again and voila! - problem solved :) As soon as I finished sending the dtmf and dropped ptt on my HT, I heard the courtesy tone come back and knew instantly that this was going to work! So that's it - my dual mode DV and FM repeater is ready!!! ;P). Thanks!!! Ramesh. www.freestar.us _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users