very good, I ended up just muting announcements altogether. Audio settings were a bit tricky, ended up having to just experiment with the settings. now got it where it sounds acceptable to us. Now last things to figure out for me now is using a gpio pin on the URI to trigger the internal pl encoder in the GE, and have it set to drop 1 second after COS loss from RF and or Internet. And to figure out how to turn off DTMF Muting, having a horrid time with RF users voice falsing the DTMF decoder thus ended up with holes in the local users transmission. propogate_dtmf=yes don't seem to work for turning off dtmf mute on local rf On Sat, 27 Jun 2015 22:45:59 -0400 mike@midnighteng.com wrote:
Glad you found it.
Here is how to change connect announcement. In extensions.conf example: exten => 29283,1,Answer exten => 29283,n,Wait(2) exten => 29283,n,Playback(rpt/node) exten => 29283,n,SayAlpha(kb8jnm) exten => 29283,n,Playback(repeater) exten => 29283,n,Rpt,29283|P
Chances are that your other inputs are to low if the announcements seem to high. Bring inputs up and cut the tx audio. Best served with a scope if you have one.
...mike/kb8jnm
well we discovered the problem.
a broken wire.
so it now works, now trying to figure out how to change the connect/disconnect messages from node # to callsign and how to lower the announcement levels without bothering the rx/tx levels
On Sat, 27 Jun 2015 19:30:26 -0400 Doug Crompton <doug@crompton.com> wrote:
If you have carrierfrom=usb then you should see the hungup status in the client when you ground pin 8. If you are not you possibly could possibly have a bad DMK-URI. Make sure you are using pin 8 on the DMK-URI NOT pin 7. Also make sure you have ctcssfrom=no 73 Doug WA3DSP http://www.crompton.com/hamradio
Date: Sat, 27 Jun 2015 11:20:54 -0400 From: w2ibc435@gmail.com To: doug@crompton.com Subject: Re: [App_rpt-users] node issues..
it don't seem to matter what I do on this thing. COR is +5 on signal. the thing floats at .7 with no signal. I can force it to a ground and the TX still stays locked no messages
carrierfrom=usb is what I am using.
its getting very close to meeting mr 20 pound sledge then going to the dump.
On Fri, 26 Jun 2015 23:11:00 -0400 Doug Crompton <doug@crompton.com> wrote:
Go into the Asterisk client. Type - asterisk -rvvv - at the Linux prompt. You should see the 'hungup' status when you release the carrier - COR untrue - not when you key. If you are not seeing the hungup command with COS change then there is either something setup wrong or a hardware problem. At least in simpleusb.conf you either set carrierfrom= usb or usbinvert - usb is high +5 COS on signal and usbinvert is low (0V) on signal. It has to be a good low!!! Less than .5 volts and preferably close to 0V in that direction.
If you can isolate the COS line and connect it to +5 and ground alternately you should see the hungup status in the client. If the logic is backwards the system thinks it is always keyed and will hold all output messages. When you are in that state it can be very confusing because nothing seems to work right. 73 Doug WA3DSP http://www.crompton.com/hamradio
Date: Fri, 26 Jun 2015 22:34:23 -0400 From: w2ibc435@gmail.com To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] node issues..
its new install, and yes it is the DMK URI. and yes repeater is hooked up.
receiver COR is active high (+5V when signal is detected) but it is doing this without any signal from the receiver cor and with signal from cor.
in usbradio.conf for COR detect I have tried DSP,USB,USBINVERTED nothing changes with the output.
On Fri, 26 Jun 2015 22:17:31 -0400 Robert Newberry <N1XBM@amsat.org> wrote:
Is this a brand new install? Is there a radio hooked to your sound card? I've run into this once where the COR pin was active high, thus disconnecting the DB25 caused it to think there was a signal on the input thus causing PTT. Are you using a DMK URI? Are you getting ptt indication?
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.