Personally I wouldn't bother with using the tone boards in the MII. On both of mine, I just pulled VOL/SQL HI from the backplane. Then let the usbradio DSP do it all. On the MIIe (direct FM exciter) I was able to feed both CG and voice into the CG input of the exciter. Measured it to be flat to 8 KC. Then let usbradio do the pre-emphasis, CG encode/decode, and de-emphasis. On the regular MII (phase modulated exciter), again all DSP. Voice into the exciter mic input, CG encode to the CG input. With the exciter doing the pre-emphasis. Robert A. Poff Loganville, Pa -------- Original Message -------- From: Chris Viningre <chrisviningre@gmail.com> Sent: Sun Nov 06 16:19:11 EST 2016 To: Bob Poff <wb3awj@comcast.net> Cc: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] No PL Tone I may have been unclear on the problem. I can not get the repeater to tone squelch. It is always open. The repeater is working fine other then that. I have tried these settings and still no luck. Thanks for all the help. Chris On 11/06/2016 10:55 AM, Bob Poff wrote:
First of all, you need carrierfrom=dsp not usb.
carrierfrom=dsp ; Carrier Detect Source ; Options - no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - via USB radio adapter COR connection ; usbinvert - same as above but inverted polarity. ; dsp - from RX noise using dsp methods ; vox - voice activated via RX audio
Take a look at: https://allstarlink.org/usbradio.html
Robert A. Poff Loganville, Pa ------------------------------------------------------------------------ *From:* Chris Viningre *Sent:* Sat Nov 05 17:19:25 EDT 2016 *To:* app_rpt-users@ohnosec.org *Subject:* [App_rpt-users] No PL Tone
I am trying to get the PL tone of 100.0 hz to work on my GE Mastr II repeater. I'm using a URI interface on a laptop running Dail software. Everything is working other than the tones. Here is my rpt.conf and usbradio.conf. Thanks for any help.
Chris Viningre 70 W. Roadrunner Salt Flat, Texas 79847 C:(915) 504-1510 chrisviningre@gmail.com Amateur Radio Operator: WS5B https://www.qrz.com/db/ws5b http://www.reverbnation.com/chrisviningre
Radio Repeater configuration file (for use with app_rpt)
;
;
; Your Repeater
;
[43934] ; Change this to your assigned node number
rxchannel=Radio/usb43934
duplex=2
erxgain=-3
etxgain=3
;controlstates=controlstates
scheduler=schedule43934
morse=morse43934
macro=macro43934
functions=functions43934
phone_functions=functions43934
link_functions=functions43934
telemetry=telemetry
wait_times=wait-times
context = radio
callerid = "Repeater" <0000000000>
idrecording = |iWS5B
accountcode=RADIO
hangtime=1000
;
; Usbradio channel driver Configuration File
;
[general]
[usb43934]
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=100.0
rxctcssfreqs=100.0
txctcssfreqs=100.0
;rxctcssoverride=0
carrierfrom=usb
ctcssfrom=usb
rxdemod=speaker
txprelim=no
txlimonly=no
txtoctype=no
txmixa=composite
txmixb=no
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0 ------------------------------------------------------------------------
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.