Thanks Doug,I'll take a look at it. I added the second node number and interface later on after the initial setup. I was not on the arm-allstar mail list, I just signed up with it.Thanks.Andrew. From: Doug Crompton <doug@crompton.com> To: KD8USF <kd8usf@yahoo.com> Cc: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Sent: Friday, August 28, 2015 8:37 PM Subject: RE: [App_rpt-users] USB Pointing problem- More info? #yiv9513218252 #yiv9513218252 --.yiv9513218252hmmessage P{margin:0px;padding:0px;}#yiv9513218252 body.yiv9513218252hmmessage{font-size:12pt;font-family:Calibri;}#yiv9513218252 I am not sure if you are listening on the arm-allstar list. If not questions on the BBB/RPi2 should be asked there. Did you follow the instructions on installing two nodes on the RPi2 in the setup how-to on hamvoip.org? You need to follow the instructions in the initial setup and then NOT move the physical USB connections. 73 Doug WA3DSP http://www.crompton.com/hamradio Date: Fri, 28 Aug 2015 20:27:03 +0000 From: kd8usf@yahoo.com To: kk6ecm@gmail.com; App_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] USB Pointing problem- More info? That brings up some questions I have about this- I have 2 interfaces on the Pi2 running Dougs image, sometimes when I reboot it, the two nodes both try to use the same interface even though they are configured in the tune files. Throws up errors in a continuous loop. When I restart asterisks from the command line it then works as it should and the two nodes are using their assigned interfaces. It's almost like the two interfaces are not fully initialized before asterisk starts on bootup. Now this is what lsusb shows: Bus 001 Device 005: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter Bus 001 Device 004: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter When I used the tune menu to set the levels it wrote in the devices as follows: For node 42051: devstr=1-1.4:1.0 For node 42078: devstr=1-1.5:1.0 Should I change that to 1-4 for node 42051, and 1-5 for node 42078? Andrew. From: kk6ecm <kk6ecm@gmail.com> To: chris <ckw@gci.net> Cc: "App_rpt-users@ohnosec.org" <App_rpt-users@ohnosec.org> Sent: Wednesday, August 26, 2015 10:23 PM Subject: Re: [App_rpt-users] Allstar You may have a USB pointing problem between asterisk and Linux. On boot up type "service asterisk stop" at the command prompt Type lsusb at the command prompt. [root@Xxxxxx~]# lsusb Bus 004 Device 004: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controller Bus 004 Device 001: ID 0000:0000 Bus 004 Device 002: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controller Bus 001 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Then make sure your tune files ( in /etc/asterisk) properly point to your USB device such as a URI in devstr= (see below example) [root@xxxxx asterisk]# cat usbradio_tune_usb<node#>.conf [usb27178] ; name=usb<node#> ; devicenum=1 devstr=4-2 ; Bus 004 Device 002: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controller rxmixerset=125 txmixaset=500 txmixbset=500 rxvoiceadj=1.820479 rxctcssadj=0.500000 txctcssadj=0 rxsquelchadj=825 Correct the tune file then At the command prompt type: service asterisk start Thanks, Bob kk6ecm Sent from iPad
On Aug 26, 2015, at 5:48 PM, chris <ckw@gci.net> wrote:
Hello Again. I failed to mention The Allstar server is running ACID. After boot up It repeats the following , (asterisk) did not claim interface 3 before use. Forgot where to fix this. Thanks again.
Chris Allstar node 42264 _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________App_rpt-users mailing listApp_rpt-users@ohnosec.orghttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-usersTo unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.