Thanks Brett. As you mention, if the computer is at one of the sites, only 1 RTCM is required. The Cactus sites do in fact repeat locally. The settings for each node are similar to using a local controller and running Asterisk/AllStar on a port of that controller. There are instructions in drupal on how to configure accordingly. The only fly in the ointment I see with this approach is getting the ID's to match the activity as the RX of a node controls the ID of that node, which in your configuration would be the TX of the opposite band. You could add a simple IDer to each TX to handle the ID of that repeater and not use Asterisk/AllStar for that. What you want to do is easily accomplished with no more that 2 RTCMs and maybe a couple of ID-o-Matic boards. tnx Mike / W5JR Milton GA
On Feb 2, 2014, at 5:03 PM, Brett Friermood <brett.friermood@gmail.com> wrote:
On Sun, Feb 2, 2014 at 2:00 PM, Steve Wright <stevewrightnz@gmail.com> wrote: Ok unless I have misread, we have two opposing opinions stated as fact.
Anyone care to offer insight, quote sources or offer configs, or otherwise generally assist in the scientific principle of distilling collective opinion for fact?
I'll take another shot at it. First, let's define a couple things:
In one of your previous emails you specified Site "A" has a transmitter on 6 meter and a receiver on 2m. Site "B" is the opposite with a transmitter on 2 meter and a 6 meter receiver. Since you are using RTCMs you can do everything with one Asterisk/app_rpt server which can be located at either site, as long as there is an active network connection between all points.
Ignoring anything Asterisk related, traditionally a system such as this will normally be configured in one of two ways. Either each repeater is individual, where 6m and 2m users are not able to talk to each other, or they are linked together, where a user transmitting on either the 2m or 6m input will be output on both bands. I did not see this explicitly specified in previous emails so I will cover both configurations below.
If setup for the linked configuration, a single RTCM can be used at each site for a total of 2. The node configuration would consist of a single node number that uses both RTCMs as voting receivers and multicast transmitters. Only one receiver can actually receive anything due to different bands, but the voting process with handle that. Once the audio is voted it will then be sent out to both transmitters.
The first way to setup the unlinked configuration is to use four RTCMs. These would then link back to two separate nodes. This would allow the ability to link the two repeaters when needed/wanted. Of course this is what you don't want because of excess RTCMs.
The "new" way that Mike (W5JR) brought up is to configure the sites as duplex bases. I believe the Cactus Intertie is a network that uses this configuration. These networks are usually set up as in-band repeaters, but the receiver audio is linked to the rest of the system and not repeated through the local transmitter.
This is what I think you are wanting to do. To do so two nodes would need to be created. One node for the Site "A" RTCM and the second for the Site "B" RTCM. Then link these through Asterisk. When the A receiver picks up a signal the audio would be sent back and sent to the B transmitter. Similarly any signal picked up by the B receiver would be sent to the A transmitter. Both appearing independent of each other.
Setting duplex=1 will not repeat the audio from receiver to transmitter, but uses half duplex operation for simplex nodes. I don't know how this will function when connected to full duplex radios instead of a half duplex mobile. Someone else would have to way in on this aspect.
Hope that helps to clear it up.
Brett KQ9N _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.