Do I leave J1 jumpers connected for 2W? -----Original Message----- From: app_rpt-bounces@lists.illiana.net [mailto:app_rpt-bounces@lists.illiana.net] On Behalf Of Steve Rodgers Sent: Friday, July 21, 2006 10:10 PM To: Asterisk Repeater Controler Subject: Re: [App_rpt] Getting app_rpt base node to work. Shane, Since you are running as a half duplex remote base please verify the following: 1. The ARIB card needs to have the 4W/2W switch set to 2W (2 wire). 2. Only one cable should be connected from the channelbank to the ARIB card. This should go from the port on the channel bank equivalent to Zap/25 to J1 on the ARIB card. 3. There should not be a txchannel defined in the nodes section of rpt.conf. 4. Since you are running as a remote base, you must add a 'y' argument to the end of the node definition, like this: 101 = radio@me.asterisk.net/101,y 5. /etc/asterisk/zapata.conf should have em_txrx for signalling on Zap/25. 6. /etc/zaptel.conf should have channel type for Zap/25 set to e&m If after verifying the above items and you still have problems: 1. The Sangoma T1 card must be able to talk to the channel bank to control the DPO port operation. We have not tested the Sangoma T1 cards with app_rpt and cannot confirm if they support DPO operation through Zaptel. Steve. On Friday 21 July 2006 16:20, Shane Burrell wrote:
It does light the red light.
-----Original Message----- From: app_rpt-bounces@lists.illiana.net [mailto:app_rpt-bounces@lists.illiana.net] On Behalf Of hwstar@rodgers.sdcoxmail.com Sent: Friday, July 21, 2006 6:29 PM To: Asterisk Repeater Controler Subject: Re: [App_rpt] Getting app_rpt base node to work.
Swap the jacks and tell me if you get a red tx light. Connecting the RX into the TX port on the ARIB should light the TX LED.
From what I can deduce, it looks like the modular cables from your channel
bank are flipping the polarity of tip and ring. The ARIB is polarity sensitive and will do exactly what you have described if the polarity is wrong.
Make up a new set of modular cables which swap the red and green wires in the opposite manner to the cables you are currently using.
Steve.
From: "Shane Burrell" <shaneb@metrostat.net> Date: 2006/07/21 Fri PM 01:08:42 PDT To: "'Asterisk Repeater Controler'" <app_rpt@lists.illiana.net> Subject: Re: [App_rpt] Getting app_rpt base node to work.
Now that I have rpt loading I can't seem to figure out how to get the base to key up. I think I have a combo of problems with my config and ARIB interface.
I have a Sangoma A104D with second T1 channels 1 and two configured. One
is
LS other is GS. The goto a TA 750 into the ARIB. I have set to 4W and jumpers 1 and 2 removed. The ARIB is connected to the KCT-19 pigtal on my Kenwood TK-880. I see the COR light come on when I receive a transmission. So far so good.
When I setup a exten to rpt|P it just gets dead air and doesn't transmit.
I
assumed that at this point I could dial *X out of the function list and
have
it do something but it doesn't. Also no audio occurs on the phone if the radio is receiving but the COR light does work.
Any pointers or next step? I've dug thru the docs and most of what I see
is
for repeaters. I just want to hit a base and send some tones. Maybe an annoucment or two.
TIA,
SHane
-----Original Message----- From: app_rpt-bounces@lists.illiana.net [mailto:app_rpt-bounces@lists.illiana.net] On Behalf Of Shane Burrell Sent: Friday, July 21, 2006 1:48 PM To: 'Asterisk Repeater Controler' Subject: Re: [App_rpt] Getting app_rpt base node to work.
I figured out I have to restart asterisk. Now I get dial and get blank
air.
My goal is to dial a number and have it send out some 2 tone. I would settle for DTMF. Is there a DTMF command I need to issue to take over/PTT the base?
-----Original Message----- From: app_rpt-bounces@lists.illiana.net [mailto:app_rpt-bounces@lists.illiana.net] On Behalf Of Jim Duuuude Sent: Friday, July 21, 2006 1:43 PM To: app_rpt@lists.illiana.net Subject: Re: [App_rpt] Getting app_rpt base node to work.
How about remote=y
It doesnt recognize remote=dump, and thinks it a node and wants an idrecording specified.
From: "Shane Burrell" <shaneb@metrostat.net> Reply-To: Asterisk Repeater Controler <app_rpt@lists.illiana.net> To: "'Asterisk Repeater Controler'" <app_rpt@lists.illiana.net> Subject: Re: [App_rpt] Getting app_rpt base node to work. Date: Fri, 21 Jul 2006 13:24:34 -0400 MIME-Version: 1.0 Received: from lists.illiana.net ([207.227.243.140]) by bay0-mc8-f19.bay0.hotmail.com with Microsoft SMTPSVC(6.0.3790.2444); Fri,
21 Jul 2006 10:24:41 -0700 Received: (qmail 3845 invoked from network); 21 Jul 2006 17:24:40 -0000 Received: from localhost (HELO ?127.0.0.1?) (127.0.0.1) by 0 with SMTP;
21
Jul 2006 17:24:40 -0000 Received: (qmail 3828 invoked from network); 21 Jul 2006 17:24:37 -0000 Received: from mail.metrostat.net (HELO mx1.metrostat.net)
(152.53.16.15)by
0 with SMTP; 21 Jul 2006 17:24:37 -0000 Received: by mx1.metrostat.net (Postfix, from userid 1003)id
2FB4F26900CC;
Fri, 21 Jul 2006 13:24:20 -0400 (EDT) Received: from compmst (unknown [152.53.16.10])by mx1.metrostat.net (Postfix) with ESMTP id D42CD26900BBfor <app_rpt@lists.illiana.net>; Fri,
21 Jul 2006 13:24:16 -0400 (EDT) X-Message-Info: LsUYwwHHNt3NYSfb1sbees3Ik0t50SZpLw6VgEAXI2s= Return-Path: <shaneb@metrostat.net> Delivered-To: mailman-app_rpt@lists.illiana.net X-Spam-Checker-Version: SpamAssassin 3.1.0 (2005-09-13) on mx1.metrostat.net X-Spam-Level: X-Spam-Status: No, score=0.0 required=5.5 tests=none autolearn=disabled version=3.1.0 X-Mailer: Microsoft Office Outlook 11 Thread-Index: Acas6IDNhxKN9qu6Qai9iAm0lrd/ggAAdqzw X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.2869 X-BeenThere: app_rpt@lists.illiana.net X-Mailman-Version: 2.1.6 Precedence: list List-Id: Asterisk Repeater Controler <app_rpt.lists.illiana.net> List-Unsubscribe:
<http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-reques
t @lists.illiana.net?subject=unsubscribe>
List-Archive: <http://lists.illiana.net/pipermail/app_rpt> List-Post: <mailto:app_rpt@lists.illiana.net> List-Help: <mailto:app_rpt-request@lists.illiana.net?subject=help> List-Subscribe:
<http://lists.illiana.net/mailman/listinfo/app_rpt>,<mailto:app_rpt-reques
t @lists.illiana.net?subject=subscribe>
Errors-To: app_rpt-bounces@lists.illiana.net X-OriginalArrivalTime: 21 Jul 2006 17:24:41.0409 (UTC) FILETIME=[8CF8FB10:01C6ACEA]
Still get rpt_exec: Cannot find specified system node 101. my rpt.conf
is
as follows:
[101] ; Node ID of remote base rxchannel = Zap/25 ; Rx audio/signalling channel txchannel = Zap/26 ; Tx audio/signalling channel functions = functions-remote remote = dumb ; Set remote=y for dumb
remote or
; remote=rbi for Doug Hall RBI1 [functions-remote] 0=remote,1 ; Retrieve Memory 1=remote,2 ; Set freq. 2=remote,3 ; Set Rx PL tone. 40=remote,100 ; Rx PL off 41=remote,101 ; Rx PL on 42=remote,102 ; Tx PL off 43=remote,103 ; Tx PL on 44=remote,104 ; Low Pwr 45=remote,105 ; Med Pwr 46=remote,106 ; Hi Pwr 5=remote,5 ; Status
[telemetry]
ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(660,880,150,2048) ct3=|t(440,0,150,2048) ct4=|t(550,0,150,2048) ct5=|t(660,0,150,2048) ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(700,1100,150,2048) remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048); remotemon=|t(1600,0,75,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
[morse] speed=20 ; Approximate speed in WPM frequency=800 ; Morse Telemetry Frequency amplitude=4096 ; Morse Telemetry Amplitude idfrequency=330 ; Morse ID Frequency idamplitude=2048 ; Morse ID Amplitude
[nodes]
;000 = context_A@1.2.3.4/1234 101 = radio@me.asterisk.net/101
;of course, you can also specify these with domain names, but why rely ;on DNS working unnecessarily?
[memory]
;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power,
transmit
PL 00 = 146.460,100.0,sht ;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power,
no
PL 01 = 146.940,100.0,-l
; The format for these entries is: Receive-Freq,Receive-PL,Attrbutes ; Attributes: l=low power, m=medium power, h=high power, -=minus offset, ; s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable
-----Original Message----- From: app_rpt-bounces@lists.illiana.net [mailto:app_rpt-bounces@lists.illiana.net] On Behalf Of hwstar@rodgers.sdcoxmail.com Sent: Friday, July 21, 2006 1:10 PM To: Asterisk Repeater Controler Subject: Re: [App_rpt] Getting app_rpt base node to work.
Shane,
1. Node numbers with leading zeroes are reserved. Try using 101 instead.
2. The node number needs to be defined in 2 places in the rpt.conf file. Once in the repeater section with square brackets e.g. [101] and once in the [NODES] section as an entry to connect to/from:
radio@127.0.0.1/101,127.0.0.1
Steve.
From: "Shane Burrell" <shaneb@metrostat.net> Date: 2006/07/21 Fri AM 10:04:30 PDT To: <app_rpt@lists.illiana.net> Subject: [App_rpt] Getting app_rpt base node to work.
I've tried to setup a base node using a kenwood TK-880 and analog
radio
board. Asterisk reports that rpt_exec: Cannot find specified system
node
001. I have 001 defined using the example base node. Is there
something I
am missing. Does app-rpt require more than a reload to get its configuration?
Regards,
Shane
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
_______________________________________________ App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt
App_rpt mailing list App_rpt@lists.illiana.net http://lists.illiana.net/mailman/listinfo/app_rpt