Hello everyone, Can anyone explain in better detail how the remote base operates, as far as users are concerned. i.e. What command do you enter to mover the frequency +500 In the documentation it shows adding? This line amongest others to the rpt.conf file. 719=remote,112 ; Bump +500 so does that mean dial 719 or *719 or? Assuming no authentication, and again if you add authentication what does the command look like? Is it *4node then a command like 719? Node is configured as a remote base, shows up with R in the node status page... Everything should be right there.. Also for the rpt.conf do I need all of this or am I missing something? ; Serial port for control ioport = /dev/ttyS0 ; Radio Type remote = ic706 ; Function list from link functions = remote-functions ; Function list from phone phone_functions = remote-functions ; Authorization level authlevel = 0 civaddr=98 duplex=0 erxgain=-3 etxgain=3 ;controlstates=controlstates scheduler=schedule29626 morse=morse29626 macro=macro29626 functions=functions29626 phone_functions=functions29626 link_functions=functions29626 link_functions=functions29626 telemetry=telemetry wait_times=wait-times context = radio callerid = "Repeater" <0000000000> idrecording = |iKC7DMF accountcode=RADIO hangtime=100 althangtime=100 totime=170000 idtime=540000 politeid=3000 etc... Are any of the std lines needed? or just the ones at top? Do I need to have all of these or are they built in? [functions-remote] 0=remote,1 ; Retrieve Memory 1=remote,2 ; Set freq. 2=remote,3 ; Set tx PL tone 3=remote,4 ; Set rx PL tone 40=remote,100 ; Rx PL off 41=remote,101 ; Rx PL on 42=remote,102 ; Tx PL off 43=remote,103 ; Tx PL on 44=remote,104 ; Low Power 45=remote,105 ; Medium Power 46=remote,106 ; High Power 711=remote,107 ; Bump -20 714=remote,108 ; Bump -100 717=remote,109 ; Bump -500 713=remote,110 ; Bump +20 716=remote,111 ; Bump +100 713=remote,110 ; Bump +20 716=remote,111 ; Bump +100 719=remote,112 ; Bump +500 721=remote,113 ; Scan - slow 724=remote,114 ; Scan - quick 727=remote,115 ; Scan - fast 723=remote,116 ; Scan + slow 726=remote,117 ; Scan + quick 729=remote,118 ; Scan + fast 79=remote,119 ; Tune (brief AM transmission for automatic antenna tuner) 51=remote,5 ; Long status query 52=remote,140 ; Short status query 67=remote,210 ; Send a * 69=remote,211 ; Send a # 91=remote,99,kc7dmf,G ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG parameter can be optionally specified ; to enforce TX band limits. http://www.voip-info.org/wiki/view/Asterisk+config+rpt.conf http://ohnosec.org/drupal/node/44 The second link a bit less clear to me... If anyone has an idea, or knows how this is supposed to work, I would appreciate it. Maybe some real world rpt.conf file you could send me, or other files I need to setup as well. A command example howto... Thanks, Mark KC7DMF