Hello, It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio. However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating: -- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194' forever keeping my radio always keyed. I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following: carrierfrom=usb ctcssfrom=no I have tried also ctcssfrom=usb as well. Any help would be appreciated. Thanks, Josh
sounds to me you are using a simplex node. In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not duplex=1. This is different from duplex= in rpt.conf I had the same symptoms when I first setup my node. Also, make sure you use the radio-tune-menu with a service monitor or some other methods to make sure your have good, clean audio being transmitted over the internet and over your node radio. ~Benjamin, KB9LFZ On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622'
-- Hungup 'Zap/pseudo-1774817359'
-- Hungup 'Zap/pseudo-691532115'
-- Hungup 'Zap/pseudo-81389311'
-- Hungup 'Zap/pseudo-465154784'
-- Hungup 'Zap/pseudo-627058532'
-- Hungup 'Zap/pseudo-1656870264'
-- Hungup 'Zap/pseudo-1671691803'
-- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb
ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop. I'm going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX. In the meantime I tried carrierfrom=vox but it didn't really seem to work. Anybody get this working properly? Thanks, Josh -----Original Message----- From: Benjamin Naber [mailto:benjamin@kb9lfz.com] Sent: Wednesday, July 03, 2013 2:37 PM To: Joshua Hintze Cc: app_rpt-users@ohnosec.org Subject: Re: [Bulk] [App_rpt-users] Issue with Hangup after first keying sounds to me you are using a simplex node. In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not duplex=1. This is different from duplex= in rpt.conf I had the same symptoms when I first setup my node. Also, make sure you use the radio-tune-menu with a service monitor or some other methods to make sure your have good, clean audio being transmitted over the internet and over your node radio. ~Benjamin, KB9LFZ On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622'
-- Hungup 'Zap/pseudo-1774817359'
-- Hungup 'Zap/pseudo-691532115'
-- Hungup 'Zap/pseudo-81389311'
-- Hungup 'Zap/pseudo-465154784'
-- Hungup 'Zap/pseudo-627058532'
-- Hungup 'Zap/pseudo-1656870264'
-- Hungup 'Zap/pseudo-1671691803'
-- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb
ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
I used carrierfrom=dsp and ctcssfrom=dsp I am not sure why folks are having serious issues with that, but it works very well, and I have zero issues with it. I do crude signal testing with it, and even when the signal from the node radio is choppy, I can still command the node to do things. I would say the biggest hurdle for getting DSP to work correctly is using the radio-tune-menu with a service monitor. This is to ensure the input and output audio audio levels are correctly set, and the DSP functions can understand the different audio freqs coming to it. I do not use a COR/COS and the node does all the CTCSS stuff. Just TX/RX audio, and PTT connections are made to the node radio. for the radio that requires 5V or active HIGH, use the K0KN PLRI interface. Very simple: a couple resistors and transistors. No need to waste time modifying a USB sound FOB, which is difficult to do because of the size of components one would be working with. ~Benjamin, KB9LFZ On Wed, 2013-07-03 at 14:48 -0600, Joshua Hintze wrote:
Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop.
I'm going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX.
In the meantime I tried carrierfrom=vox but it didn't really seem to work. Anybody get this working properly?
Thanks,
Josh
-----Original Message----- From: Benjamin Naber [mailto:benjamin@kb9lfz.com] Sent: Wednesday, July 03, 2013 2:37 PM To: Joshua Hintze Cc: app_rpt-users@ohnosec.org Subject: Re: [Bulk] [App_rpt-users] Issue with Hangup after first keying
sounds to me you are using a simplex node.
In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not duplex=1. This is different from duplex= in rpt.conf
I had the same symptoms when I first setup my node.
Also, make sure you use the radio-tune-menu with a service monitor or some other methods to make sure your have good, clean audio being transmitted over the internet and over your node radio.
~Benjamin, KB9LFZ
On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622'
-- Hungup 'Zap/pseudo-1774817359'
-- Hungup 'Zap/pseudo-691532115'
-- Hungup 'Zap/pseudo-81389311'
-- Hungup 'Zap/pseudo-465154784'
-- Hungup 'Zap/pseudo-627058532'
-- Hungup 'Zap/pseudo-1656870264'
-- Hungup 'Zap/pseudo-1671691803'
-- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb
ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
I too would suggest using the DSP. Sure is easier to bring out discriminator audio than muck about building extra logic. As to not using PL...... please reconsider. It's quite frustrating to be connected to a large network and hearing the squelch on one node popping because of local noise or band conditions. Meanwhile, the DSP generally does a good job of decoding it. -- Sent from my Android phone with K-9 Mail. Please excuse my brevity.
Joshua, I'm going to take a chance here and state what seems to be the obvious; all your additional work to get your node functional seem to stem from the rather unusual radio you are using. So why not just bite the bullet and change radios to something a bit more standard, like a ham dual-band FM radio for some flexability, or maybe a ham monoband HT or mobile radio to save both time and money? Seems the time and effort you have put into getting the AM aircraft radio to function would be moot with just about any ham FM radio replacing it. And if you get one with a data-access conection, all the signals you need are there so you can run COR or stratight audio relatively easily, whatever your choice? Or have I missed something obvious related to your choice of radios? Just a thought. --- On Wed, 7/3/13, Joshua Hintze <joshh@imsar.com> wrote: From: Joshua Hintze <joshh@imsar.com> Subject: Re: [App_rpt-users] [Bulk] Issue with Hangup after first keying To: "'Benjamin Naber'" <benjamin@kb9lfz.com> Cc: app_rpt-users@ohnosec.org Date: Wednesday, July 3, 2013, 8:48 PM Thanks Ben for the quick feedback. I think I might have figured it out. It turns out my COR signal might not necessarily be the best COR signal. It looks like the signal goes high on BOTH RX and TX. This is probably causing asterisk to think its receiving when its sending getting into a nice infinite loop. I'm going to try an AND gate with the PTT so that PTT has to be high (i.e. NOT TX) and speaker mute (my COR) has to be high for a true COR output on RX. In the meantime I tried carrierfrom=vox but it didn't really seem to work. Anybody get this working properly? Thanks, Josh -----Original Message----- From: Benjamin Naber [mailto:benjamin@kb9lfz.com] Sent: Wednesday, July 03, 2013 2:37 PM To: Joshua Hintze Cc: app_rpt-users@ohnosec.org Subject: Re: [Bulk] [App_rpt-users] Issue with Hangup after first keying sounds to me you are using a simplex node. In your simpleusb.conf or usbradio.conf, ensure duplex=0, and not duplex=1. This is different from duplex= in rpt.conf I had the same symptoms when I first setup my node. Also, make sure you use the radio-tune-menu with a service monitor or some other methods to make sure your have good, clean audio being transmitted over the internet and over your node radio. ~Benjamin, KB9LFZ On Wed, 2013-07-03 at 13:58 -0600, Joshua Hintze wrote:
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622'
-- Hungup 'Zap/pseudo-1774817359'
-- Hungup 'Zap/pseudo-691532115'
-- Hungup 'Zap/pseudo-81389311'
-- Hungup 'Zap/pseudo-465154784'
-- Hungup 'Zap/pseudo-627058532'
-- Hungup 'Zap/pseudo-1656870264'
-- Hungup 'Zap/pseudo-1671691803'
-- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb
ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Replacing the air band radio with an amateur grade FM radio would be rather useless when trying to communicate with aircraft on VHF-AM. I'm sure Josh has a perfectly valid reason for using that radio. Brett KQ9N On Thu, Jul 4, 2013 at 6:58 AM, Bill South <wbs099@yahoo.com> wrote:
Joshua, I'm going to take a chance here and state what seems to be the obvious; all your additional work to get your node functional seem to stem from the rather unusual radio you are using. So why not just bite the bullet and change radios to something a bit more standard, like a ham dual-band FM radio for some flexability, or maybe a ham monoband HT or mobile radio to save both time and money? Seems the time and effort you have put into getting the AM aircraft radio to function would be moot with just about any ham FM radio replacing it. And if you get one with a data-access conection, all the signals you need are there so you can run COR or stratight audio relatively easily, whatever your choice? Or have I missed something obvious related to your choice of radios? Just a thought.
On 7/5/2013 12:17 AM, Brett Friermood wrote:
Replacing the air band radio with an amateur grade FM radio would be rather useless when trying to communicate with aircraft on VHF-AM. I'm sure Josh has a perfectly valid reason for using that radio.
Aware (painfully) of the diffferences, having owned a certificated (ie could yellow-tag nav/comm/xpdr/mb/ils/etc) avionics shop years ago...right about the time GPS came along (the KLN-88 was the hot navigation device way back then...). As long as the proper precautions were taken to not cross-service connect...one service does not require an operator certificate (unless traveling outside the US, in which case a restricted radiotelephone op permit, IIRC, is required, though the aircraft station is licensed (call sign is the N number)), the other requires both an op and station license. IOW, you can't use 122.9 (multicom) as a simplex channel to bring up your 145.25 repeater and talk to your mates....;) Wasn't questioning what he was trying to do, just the mode, interface differences, and equipment that he was using to do so. bb
Are you running full duplex on a simplex radio? Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying Hello, It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio. However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating: -- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194' forever keeping my radio always keyed. I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following: carrierfrom=usb ctcssfrom=no I have tried also ctcssfrom=usb as well. Any help would be appreciated. Thanks, Josh -- This message was scanned and is believed to be clean. Click here to report this message as spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD>
Forget this emaill. I should learn to read all my emails before replying to an old one... Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Corey Dean [n3fe@repeater.net] Sent: Thursday, July 04, 2013 10:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Issue with Hangup after first keying Are you running full duplex on a simplex radio? Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying Hello, It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio. However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating: -- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194' forever keeping my radio always keyed. I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following: carrierfrom=usb ctcssfrom=no I have tried also ctcssfrom=usb as well. Any help would be appreciated. Thanks, Josh -- This message was scanned and is believed to be clean. Click here to report this message as spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93BD> _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users -- This message was scanned and is believed to be clean. Click here to report this message as spam. http://simba.repeater.net/cgi-bin/learn-msg.cgi?id=E2134221A.A8DD0
Ok all I'm back to work today and playing with this setup again. I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues. As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf duplex=0 ; Full Duplex rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1 Just for clarity I'll post my entire usbradio.conf below: [general] [usb] hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1 ;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work. rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis. txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst") txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above. invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this. duplex=0 ; Full Duplex rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1 Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence. Thanks, Josh -----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying Are you running full duplex on a simplex radio? Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying Hello, It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio. However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating: -- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194' forever keeping my radio always keyed. I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following: carrierfrom=usb ctcssfrom=no I have tried also ctcssfrom=usb as well. Any help would be appreciated. Thanks, Josh -- This message was scanned and is believed to be clean. Click here to report this message as spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B D>
For a simplex node be sure that you have the following defined in: /etc/asterisk/rpt.conf duplex=0 (for no telemetry / messasges) or duplex=1 (enables telemetry / messages / courtesy tones) This is a different setting than the duplex = in your usbradio.conf file N5ZUA ----- Original Message ----- From: "Joshua Hintze" <joshh@imsar.com> To: "'Corey Dean'" <n3fe@repeater.net>; <app_rpt-users@ohnosec.org> Sent: Friday, July 05, 2013 12:56 PM Subject: Re: [App_rpt-users] Issue with Hangup after first keying
Ok all I'm back to work today and playing with this setup again.
I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues.
As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Just for clarity I'll post my entire usbradio.conf below:
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.
rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator
txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this.
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence.
Thanks,
Josh
-----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Are you running full duplex on a simplex radio?
Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
-- This message was scanned and is believed to be clean. Click here to report this message as spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B D>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Wow that is it! My rpt.conf did not even have a duplex setting in it so I had no idea that it needed to be set. Grrrrr Seems to be working much better now. Thanks! Josh -----Original Message----- From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Steve Agee Sent: Friday, July 05, 2013 12:05 PM To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Issue with Hangup after first keying For a simplex node be sure that you have the following defined in: /etc/asterisk/rpt.conf duplex=0 (for no telemetry / messasges) or duplex=1 (enables telemetry / messages / courtesy tones) This is a different setting than the duplex = in your usbradio.conf file N5ZUA ----- Original Message ----- From: "Joshua Hintze" <joshh@imsar.com> To: "'Corey Dean'" <n3fe@repeater.net>; <app_rpt-users@ohnosec.org> Sent: Friday, July 05, 2013 12:56 PM Subject: Re: [App_rpt-users] Issue with Hangup after first keying
Ok all I'm back to work today and playing with this setup again.
I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues.
As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Just for clarity I'll post my entire usbradio.conf below:
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.
rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator
txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this.
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence.
Thanks,
Josh
-----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Are you running full duplex on a simplex radio?
Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
-- This message was scanned and is believed to be clean. Click here to report this message as
spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B
D>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Correct. The default does not define that value, and thus it is assumed at full duplex / repeater setting. Good deal! N5ZUA ----- Original Message ----- From: "Joshua Hintze" <joshh@imsar.com> To: "'Steve Agee'" <n5zua@earthlink.net>; <app_rpt-users@ohnosec.org> Sent: Friday, July 05, 2013 1:06 PM Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Wow that is it!
My rpt.conf did not even have a duplex setting in it so I had no idea that it needed to be set. Grrrrr
Seems to be working much better now.
Thanks!
Josh
-----Original Message----- From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Steve Agee Sent: Friday, July 05, 2013 12:05 PM To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Issue with Hangup after first keying
For a simplex node be sure that you have the following defined in:
/etc/asterisk/rpt.conf
duplex=0 (for no telemetry / messasges)
or
duplex=1 (enables telemetry / messages / courtesy tones)
This is a different setting than the duplex = in your usbradio.conf file
N5ZUA
----- Original Message ----- From: "Joshua Hintze" <joshh@imsar.com> To: "'Corey Dean'" <n3fe@repeater.net>; <app_rpt-users@ohnosec.org> Sent: Friday, July 05, 2013 12:56 PM Subject: Re: [App_rpt-users] Issue with Hangup after first keying
Ok all I'm back to work today and playing with this setup again.
I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues.
As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Just for clarity I'll post my entire usbradio.conf below:
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.
rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator
txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this.
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence.
Thanks,
Josh
-----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Are you running full duplex on a simplex radio?
Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
-- This message was scanned and is believed to be clean. Click here to report this message as
spam.<http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B
D>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
I stand corrected. You should be just fine though there is a duplex setting in usbradio.conf too. http://ohnosec.org/drupal/node/84 On Jul 5, 2013 11:58 AM, "Joshua Hintze" <joshh@imsar.com> wrote:
Ok all I'm back to work today and playing with this setup again.
I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues.
As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Just for clarity I'll post my entire usbradio.conf below:
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.
rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator
txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this.
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence.
Thanks,
Josh
-----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Are you running full duplex on a simplex radio?
Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org ] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
-- This message was scanned and is believed to be clean. Click here to report this message as spam.< http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B D>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Try this too http://ohnosec.org/drupal/node/193 On Jul 5, 2013 12:26 PM, "Jeff Carrier" <k0jsc.jeff@gmail.com> wrote:
I stand corrected. You should be just fine though there is a duplex setting in usbradio.conf too.
http://ohnosec.org/drupal/node/84 On Jul 5, 2013 11:58 AM, "Joshua Hintze" <joshh@imsar.com> wrote:
Ok all I'm back to work today and playing with this setup again.
I was able to isolate a much better signal for COR than what I had before. This now truely goes from 0V->5V only when receiving and not when transmitting. However I'm still having issues.
As soon as asterisk receives a signal it immediately tries to transmit a signal out. This then effectively pulls the PTT low and my receiver stops receiving. It is almost like it is in duplex mode but I have in usbradio.conf
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Just for clarity I'll post my entire usbradio.conf below:
[general]
[usb]
hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces.
rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output
rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1
;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted rxctcssoverride=1 ; Set to 1 or yes to start out in carrier squelch mode
carrierfrom=usb ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio
ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work.
rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio
txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator
txlimonly=no ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis.
txtoctype=no ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst")
txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring
txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above.
invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this.
duplex=0 ; Full Duplex
rxondelay=0 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. eeprom=1
Any thoughts on why asterisk would be trying to send a signal as soon as it receives one? After the first time (upon asterisk restart) it receives a signal it sends a beep followed by a morse code sequence.
Thanks,
Josh
-----Original Message----- From: Corey Dean [mailto:n3fe@repeater.net] Sent: Thursday, July 04, 2013 8:48 AM To: Joshua Hintze; app_rpt-users@ohnosec.org Subject: RE: [App_rpt-users] Issue with Hangup after first keying
Are you running full duplex on a simplex radio?
Corey N3FE ________________________________________ From: app_rpt-users-bounces@ohnosec.org [ app_rpt-users-bounces@ohnosec.org] On Behalf Of Joshua Hintze [joshh@imsar.com] Sent: Wednesday, July 03, 2013 3:58 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Issue with Hangup after first keying
Hello,
It is my first posting on here. I have ALMOST gotten the ACID installation working. I'm using the URI interfaced to ACID and to my radio. The asterisk can properly key the radio and its working just fine with that. I can also connect to the node with iaxRpt directly with no problem and transmit OUT of my radio.
However I am having some issues when my radio receives communication in that as soon as I get my first radio RX, asterisk will then play a tone out of the URI into the radio over and over again at about a one second interval. In the asterisk terminal it just keeps repeating:
-- Hungup 'Zap/pseudo-1726358622' -- Hungup 'Zap/pseudo-1774817359' -- Hungup 'Zap/pseudo-691532115' -- Hungup 'Zap/pseudo-81389311' -- Hungup 'Zap/pseudo-465154784' -- Hungup 'Zap/pseudo-627058532' -- Hungup 'Zap/pseudo-1656870264' -- Hungup 'Zap/pseudo-1671691803' -- Hungup 'Zap/pseudo-50274194'
forever keeping my radio always keyed.
I have the COR from the radio going into the URI. I do not plan on using CTCSS and have tried tying it to ground as well as tying it to the COR as well. My usbradio.conf has the following:
carrierfrom=usb ctcssfrom=no
I have tried also ctcssfrom=usb as well.
Any help would be appreciated.
Thanks,
Josh
-- This message was scanned and is believed to be clean. Click here to report this message as spam.< http://simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=6EF48221A.A93B D>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
participants (9)
-
Benjamin Naber -
Bill South -
Brett Friermood -
Bryan D. Boyle -
Corey Dean -
Jeff Carrier -
Joshua Hintze -
Robert a. Poff -
Steve Agee