Hi   I believe I only enabled the COR.   it would seem that I should find a older computer perhaps.   Chris ________________________________ From: Pierre Martel <petem001@hotmail.com> To: C B <harvard5362@yahoo.com> Sent: Sunday, August 25, 2013 1:37 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 I had the same problem and was suspecting dsp. I did un update to latest svn. and was stillg etting same thing. Are you using any dsp on your node? ctcss decoding, cor, ect? From: C B Sent: Sunday, August 25, 2013 2:10 PM To: Paul J. Agamata ; app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Hi   I did what you suggested and it seems to complete without error.   However it did not resolve the problem.   I ran the same commands for Asterisk, still the same issue.   Reran the Zaptel compile / install again and still no luck.   I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt.   after reinstalling I looked at the /root/acid­install.log and I did not see anything that looked like an error.   Am I forgetting something or could my hardware not be combatable?   As part of this project I did install this successfully on a different computer.   Any help greatly appreciated.   Chris ________________________________ From: Paul J. Agamata <Sysman@Xceptions.COM> To: C B <harvard5362@yahoo.com> Sent: Saturday, August 24, 2013 4:57 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Log into your 'root' account and navigate to the 'zaptel' directory. When your in there type the following: ./configure <enter> make <enter> make install <enter> Then reboot your computer and everything should be fine. _______________________________ Paul J. Agamata WH6FM Sysman@Xceptions.COM Hilo, Hawaii From: C B <harvard5362@yahoo.com> Reply-To: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:54 PM To: Paul Agamata <Sysman@Xceptions.COM> Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Paul   Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of.   is there anything you can refer me to that will contain instructions on how to do this?   Is it something I did wrong?   Sorry for not having a lot of experience.   And thank you for your help.   Chris ________________________________ From: Paul J. Agamata <Sysman@Xceptions.COM> To: C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Sent: Saturday, August 24, 2013 4:46 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 This is indicative of the zaptel drivers not in your kernel.  Compile/Install then reboot and all should be well.  The 'zaptel' directory is in the 'asterisk' source directory. Be aware that if you update your kernel you will need to re-install the zaptel modules. Regards, Paul _______________________________ Paul J. Agamata WH6FM Sysman@Xceptions.COM Hilo, Hawaii From: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:23 PM To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Asterisk ended with exit status 1 Hi I am attempting to build a ACID node. After several attempts of reinstalling the ACID with the same results I am asking for some help. All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating. mpg123: no process killed Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk Computer is a HPdc5700 small form factor 1 GIG memory 500 GB SATA HDD than you in advance for any help Chris ________________________________ _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users