I am trying to have a permanent link between my 2 nodes. I put the following in rpt.conf [27360] startup_macro=*327383 While it does bring up the link when the system starts, if there are any errors or if anything disrupts the connection then 27360 just says "disconnected" and never tries to re-establish the permanent link. Is there another configuration command that I need so that this will re-connect after a disconnect? (such as when the 27383 system reboots) Chuck
I oculd be wrong but I thought you had to create the macro first and then point the startup_macro to the correct macro. From: app_rpt-users-bounces@qrvc.com [mailto:app_rpt-users-bounces@qrvc.com] On Behalf Of Chuck Henderson Sent: Wednesday, November 03, 2010 6:40 AM To: app_rpt-users@qrvc.com Subject: [App_rpt-users] permalink question I am trying to have a permanent link between my 2 nodes. I put the following in rpt.conf [27360] startup_macro=*327383 While it does bring up the link when the system starts, if there are any errors or if anything disrupts the connection then 27360 just says "disconnected" and never tries to re-establish the permanent link. Is there another configuration command that I need so that this will re-connect after a disconnect? (such as when the 27383 system reboots) Chuck -- This message was scanned and is believed to be clean. Click here to report this message as spam.<%0d%0ahttp:/simba.repeater.net:8080/cgi-bin/learn-msg.cgi?id=8492F2F966.AEAFB%0d%0a>
It should be: startup_macro=*95327383 rpt.conf 951=ilink,11 ; Specific Link permanent connect - monitor only 952=ilink,12 ; Specific Link permanent connect - monitor only *953=ilink,13 ; Specific Link permanent connect - transceive* 954=ilink,6 ; Disconnect all links including permalinks David On Wed, Nov 3, 2010 at 3:40 AM, Chuck Henderson < rpt2@chuck.midlandsnetworking.com> wrote:
I am trying to have a permanent link between my 2 nodes. I put the following in rpt.conf
[27360] startup_macro=*327383
While it does bring up the link when the system starts, if there are any errors or if anything disrupts the connection then 27360 just says "disconnected" and never tries to re-establish the permanent link.
Is there another configuration command that I need so that this will re-connect after a disconnect? (such as when the 27383 system reboots)
Chuck
_______________________________________________ App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users
It works!!! And I think I am starting to understand the configuration a little now. Thank you Chuck On Wed, Nov 3, 2010 at 10:07 AM, David KE6UPI <dshaw@ke6upi.com> wrote:
It should be: startup_macro=*95327383
rpt.conf 951=ilink,11 ; Specific Link permanent connect - monitor only 952=ilink,12 ; Specific Link permanent connect - monitor only *953=ilink,13 ; Specific Link permanent connect - transceive* 954=ilink,6 ; Disconnect all links including permalinks
David
On Wed, Nov 3, 2010 at 3:40 AM, Chuck Henderson < rpt2@chuck.midlandsnetworking.com> wrote:
I am trying to have a permanent link between my 2 nodes. I put the following in rpt.conf
[27360] startup_macro=*327383
While it does bring up the link when the system starts, if there are any errors or if anything disrupts the connection then 27360 just says "disconnected" and never tries to re-establish the permanent link.
Is there another configuration command that I need so that this will re-connect after a disconnect? (such as when the 27383 system reboots)
Chuck
_______________________________________________
App_rpt-users mailing list App_rpt-users@qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users
participants (3)
-
Chuck Henderson -
Corey Dean N3FE -
David KE6UPI