It works FINE!! You have to send digits to the node that has the propagate_dtmf, and it will output them. For example, if the node that has that set up is 1234, then you need, once you link to it from a different node, do a *41234 (into command mode for node 1234), then whatever digits you send to it will go out the main interface for node 1234. Jim WB6NIL Date: Mon, 29 Oct 2012 22:16:34 -0400 From: kb2faf@arrl.net To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Fwd: Dtmf pass through FYI, I have the same problem and have tried everything indicated below with no luck. It can't be this complicated can it? Chris KB2FAF On 10/29/2012 04:19 PM, Ian Venable wrote: So I still am having trouble with this. So far I have added propagate_dtmf=yes linktolink=yes inxlat=#56,#57,0123456789ABCD outxlat=#56,#57,0123456789ABCD to the rpt.conf file on the node that has the cat200b controller attached to it. Also on both of my other nodes that are connected via the allstar system i have added propagate_dtmf=yes to there rpt.conf files. I have done a restart on all the nodes, and still not getting the dtmf to pass through. When the dtmf passes through you should be able to hear it on the output of the repeaters, right? As long as it is not started with a (*) then the node would try to act on the dtmf. The cat200b controller is in remote base weather mode, and does not require COR, or PL to act, all it is looking at is the Tx audio from the usb fob, which goes into the Rx port on the controller. So all the controller needs to hear is the DTMF audio, but its not getting there. The controllers Tx audio is connected to the Rx audio on the usb fob, and I know thats working because I hear the controller identify itself with its version when I power cycle it. I am probably doing something wrong, so hopefully someone could point me in the right direction. Thanks! Ian Ki6ies On Sun, Oct 28, 2012 at 5:42 PM, Ken <ke2n@cs.com> wrote: *4 sends “telemetry” (control codes) to the other node … not DTMF I think you want propagate_dtmf=yes in the node stanza Ken From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of ki6ies.tasma@gmail.com Sent: Sunday, October 28, 2012 5:31 PM To: app_rpt-users@ohnosec.org Subject: [App_rpt-users] Fwd: Dtmf pass through -------- Original Message -------- Subject: Dtmf pass through From: ki6ies.tasma@gmail.com To: app_rpt-users-request@ohnosec.org CC: Hello all! I need some help. I am trying to control a cat200 repeater controller via dtmf. It is its own node. I have my other node (uhf repeater)connected to it, from which i would like to send the commands from. I have tried the *4 and the node number. And then i hear "By your command". But dtmf is not making it to the controller. It is making it to the other node, because I can issue it commands. It is just not passing through the other node, which i would like for it to do. Any thoughts? Ian Sent from my Verizon Wireless 4G LTE DROID _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users