It would be hard to know what type of remote base you are setting up to help because you did not state it. Basically, it is just another node.Set-up everything a node needs. If it is a freq agile remote base you need: To tell app_rpt what it is and the method of communications (com/usb ports) to it (except rbi-1 is parport only) Such as but not limited to depending on remote type- ioport=/dev/ttyUSB0 ; Serial port for control (usb serial 1) iospeed=19200 ; io speed for port iobase = 0x378 ; Specify IO port for parallel port remote=ic706 ; Remote Radio Type civaddr=72 ; ic706 dev address Command structure for control included in that nodes set-up. (you may not need all of these depending on what you are using) 0=remote,1 ; Retrieve Memory 1=remote,2 ; Set freq. VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset) 2=remote,3 ; Set tx PL tone PL Tone HHH*D* 3=remote,4 ; Set rx PL tone HHH*D* 6=remote,6 ; Set mode 1=FM 2=USB 3=LSB 4=AM 40=remote,100 ; Rx PL off 41=remote,101 ; Rx PL on 42=remote,102 ; Tx PL off 43=remote,103 ; Tx PL on 44=remote,104 ; Low Power 45=remote,105 ; Medium Power 46=remote,106 ; High Power 51=remote,5 ; Long status query 52=remote,140 ; Short status query 67=remote,210 ; Send a * 69=remote,211 ; Send a # 79=remote,119 ; Tune (brief AM transmission for automatic antenna tuner) 711=remote,107 ; Bump -20 714=remote,108 ; Bump -100 717=remote,109 ; Bump -500 713=remote,110 ; Bump +20 716=remote,111 ; Bump +100 719=remote,112 ; Bump +500 721=remote,113 ; Scan - slow 724=remote,114 ; Scan - quick 727=remote,115 ; Scan - fast 723=remote,116 ; Scan + slow 726=remote,117 ; Scan + quick 729=remote,118 ; Scan + fast If it is a stand alone RB or a party-line type of node... If one connection at a time, use ",y" at the definition line: 29261 = radio@127.0.0.1/29261,NONE,y ;y=remote base If connecting to it from other node, you will want to use *5(node#) for control of it from the other node. There are some other ways of doing that depending on your set-up. Can't write the book here so I hope that helps some. ...mike/kb8jnm

Better yet, does anyone have any examples they could share? Looking to have a regular node and remote base on the same server. I think I have most of it right, just want to make sure.

Jamey WR4JW ________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] on behalf of Jamey Wright [Jamey.Wright@morgan911.org] Sent: Friday, July 17, 2015 8:23 PM To: APP RPT ý[app_rpt-users@ohnosec.org]ý Subject: [App_rpt-users] Remote Bases

I am getting ready to set up a remote base. I have been reading through the docs on the site and I have most of it but just wanted to verify that remote base node stanza info goes into the rpt.conf config file.

Thanks

Jamey WR4JW _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

I am using a Kenwood TM-271. I think I have most of it figured out. Just have to make time to go to the site and install the radio and test all of it. Jamey Wright WR4JW -----Original Message----- From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of mike@midnighteng.com Sent: Friday, July 17, 2015 10:17 PM To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Remote Bases It would be hard to know what type of remote base you are setting up to help because you did not state it. Basically, it is just another node.Set-up everything a node needs. If it is a freq agile remote base you need: To tell app_rpt what it is and the method of communications (com/usb ports) to it (except rbi-1 is parport only) Such as but not limited to depending on remote type- ioport=/dev/ttyUSB0 ; Serial port for control (usb serial 1) iospeed=19200 ; io speed for port iobase = 0x378 ; Specify IO port for parallel port remote=ic706 ; Remote Radio Type civaddr=72 ; ic706 dev address Command structure for control included in that nodes set-up. (you may not need all of these depending on what you are using) 0=remote,1 ; Retrieve Memory 1=remote,2 ; Set freq. VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset) 2=remote,3 ; Set tx PL tone PL Tone HHH*D* 3=remote,4 ; Set rx PL tone HHH*D* 6=remote,6 ; Set mode 1=FM 2=USB 3=LSB 4=AM 40=remote,100 ; Rx PL off 41=remote,101 ; Rx PL on 42=remote,102 ; Tx PL off 43=remote,103 ; Tx PL on 44=remote,104 ; Low Power 45=remote,105 ; Medium Power 46=remote,106 ; High Power 51=remote,5 ; Long status query 52=remote,140 ; Short status query 67=remote,210 ; Send a * 69=remote,211 ; Send a # 79=remote,119 ; Tune (brief AM transmission for automatic antenna tuner) 711=remote,107 ; Bump -20 714=remote,108 ; Bump -100 717=remote,109 ; Bump -500 713=remote,110 ; Bump +20 716=remote,111 ; Bump +100 719=remote,112 ; Bump +500 721=remote,113 ; Scan - slow 724=remote,114 ; Scan - quick 727=remote,115 ; Scan - fast 723=remote,116 ; Scan + slow 726=remote,117 ; Scan + quick 729=remote,118 ; Scan + fast If it is a stand alone RB or a party-line type of node... If one connection at a time, use ",y" at the definition line: 29261 = radio@127.0.0.1/29261,NONE,y ;y=remote base If connecting to it from other node, you will want to use *5(node#) for control of it from the other node. There are some other ways of doing that depending on your set-up. Can't write the book here so I hope that helps some. ...mike/kb8jnm

Better yet, does anyone have any examples they could share? Looking to have a regular node and remote base on the same server. I think I have most of it right, just want to make sure.

Jamey WR4JW ________________________________ From: app_rpt-users-bounces@ohnosec.org [app_rpt-users-bounces@ohnosec.org] on behalf of Jamey Wright [Jamey.Wright@morgan911.org] Sent: Friday, July 17, 2015 8:23 PM To: APP RPT ý[app_rpt-users@ohnosec.org]ý Subject: [App_rpt-users] Remote Bases

I am getting ready to set up a remote base. I have been reading through the docs on the site and I have most of it but just wanted to verify that remote base node stanza info goes into the rpt.conf config file.

Thanks

Jamey WR4JW _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.