pl stops encoding for about a half of a second on a RTCM setup
Question, I have been working on the TRCMs and I notices a small issue. There is one thing that we can't figure out and that is we are encoding a PL of 100 but we are noticing that every 8 seconds the pl stops encoding for about a half of a second then restarts encoding. You can hold down the ptt on a HT and just watch the repeater on a service monitor and see the tone dropping while the carrier stays there.. the two RTCMs have S/W Version: 1.11 11/04/2012 on them. It looks like a timing setting I have wrong if someone could point me in the right direction I would be appreciated. Thanks KC5DAQ
Hi! I have installed as Buddy Brannan, KB5ELV told me the ezstream software to feed a stream to radioreference.com so that our user could hear our system like we used to do, but this was from a wmencoder in windows and this was feed by port 3 of the rc-210 we have at the repeater site. so I got this file: http://allstarlink.org/acid-stream.tar.gz untar it and started the compiling/installing all went well. then I added to my rpt.conf file under the 27821 (my node number) section this: outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8.0 --bitwidth 16 --resample 22050 - - | /usr/bin/ezstream -c /etc/ezstream.xml all was working A1 . But cause there is allways a BUT... After asking the allstar server to reload my node (cause I goofed with some stuff.) the stream did not started back.. of course went back to rpt.conf and did as before with the outstreamcmd command. but still no go. anyone have an Idea what could be causing this?
not sure what you are streaming *to*? if you are using a 3rd party streaming server, you may have to log onto that service (its control panel or dashboard or whatever) and restart the service from that end - particularly if you have changed something. GL Ken -----Original Message----- From: pete M <petem001@hotmail.com> To: APP RPT <App_rpt-users@ohnosec.org> Sent: Mon, Jan 7, 2013 12:33 pm Subject: [App_rpt-users] no more streaming.. Hi! I have installed as Buddy Brannan, KB5ELV told me the ezstream software to eed a stream to radioreference.com so that our user could hear our system ike we used to do, but this was from a wmencoder in windows and this was eed by port 3 of the rc-210 we have at the repeater site. so I got this file: http://allstarlink.org/acid-stream.tar.gz untar it and started the compiling/installing all went well. then I added to my rpt.conf file under the 27821 (my node number) section his: outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s .0 --bitwidth 16 --resample 22050 - - | /usr/bin/ezstream -c etc/ezstream.xml all was working A1 . But cause there is allways a BUT... After asking the llstar server to reload my node (cause I goofed with some stuff.) the tream did not started back.. of course went back to rpt.conf and did as before with the outstreamcmd ommand. but still no go. anyone have an Idea what could be causing this? ______________________________________________ pp_rpt-users mailing list pp_rpt-users@ohnosec.org ttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
If you reloaded your node config from the Allstar server, it overwrites all of your config files in the asterisk directory. So if you had other things that work in conjunction with the streaming then all of that set up is gone. Its always best to keep a local back up copy of the asterisk directory in case you lose you node configs to a hd crash or other mishaps. That way you can build a new box with default setting and just copy over the asterisk directory and bingo you are back on line. Jon VA3RQ On 1/7/2013 12:32 PM, pete M wrote:
Hi!
I have installed as Buddy Brannan, KB5ELV told me the ezstream software to feed a stream to radioreference.com so that our user could hear our system like we used to do, but this was from a wmencoder in windows and this was feed by port 3 of the rc-210 we have at the repeater site.
so I got this file: http://allstarlink.org/acid-stream.tar.gz
untar it and started the compiling/installing all went well.
then I added to my rpt.conf file under the 27821 (my node number) section this:
outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8.0 --bitwidth 16 --resample 22050 - - | /usr/bin/ezstream -c /etc/ezstream.xml
all was working A1 . But cause there is allways a BUT... After asking the allstar server to reload my node (cause I goofed with some stuff.) the stream did not started back..
of course went back to rpt.conf and did as before with the outstreamcmd command. but still no go.
anyone have an Idea what could be causing this?
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Thats something I will do as soon as my system is back as I wish... -----Message d'origine----- From: Jon Rorke Sent: Monday, January 07, 2013 1:19 PM Cc: APP RPT Subject: Re: [App_rpt-users] no more streaming.. If you reloaded your node config from the Allstar server, it overwrites all of your config files in the asterisk directory. So if you had other things that work in conjunction with the streaming then all of that set up is gone. Its always best to keep a local back up copy of the asterisk directory in case you lose you node configs to a hd crash or other mishaps. That way you can build a new box with default setting and just copy over the asterisk directory and bingo you are back on line. Jon VA3RQ On 1/7/2013 12:32 PM, pete M wrote:
Hi!
I have installed as Buddy Brannan, KB5ELV told me the ezstream software to feed a stream to radioreference.com so that our user could hear our system like we used to do, but this was from a wmencoder in windows and this was feed by port 3 of the rc-210 we have at the repeater site.
so I got this file: http://allstarlink.org/acid-stream.tar.gz
untar it and started the compiling/installing all went well.
then I added to my rpt.conf file under the 27821 (my node number) section this:
outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8.0 --bitwidth 16 --resample 22050 - - | /usr/bin/ezstream -c /etc/ezstream.xml
all was working A1 . But cause there is allways a BUT... After asking the allstar server to reload my node (cause I goofed with some stuff.) the stream did not started back..
of course went back to rpt.conf and did as before with the outstreamcmd command. but still no go.
anyone have an Idea what could be causing this?
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
participants (4)
-
Gary Herzog Gmail -
Jon Rorke -
Ken -
pete M