On 2017-07-27 7:57 AM, Luc Drolet VE2 LUQ wrote:

Hello Ramesh,

Here is attached file 2 PDF Of my pictures with PuTTY, I choose 2) Set Rx Voice Level (using display)

Subsequently I want to adjust my audio and also recorded my configurations

<-- Hi Luc: Thanks for the screen shot - this is very helpful as it clarifies which image you are using. You are using the hamvoip image (https://hamvoip.org/). You will have to subscribe to that mailing list for instructions / support. This is the original app_rpt / Allstar link support group. We use and support the allstarlink image (available from: https://allstarlink.org/) in honor of our late friend, Jim Dixon, WB6NIL. Should you choose to use this image, we are here to provide support as required. 73 de Ramesh, VA3UV

I would add, I adjust all the audio input and output of the radio to -10dBm, and set the USB interface to that. This way I can swap interfaces without need to reset the levels. -- Bryan Fields M: +1-727-409-1194

On Jul 27, 2017, at 10:48, Benjamin Naber <Benjamin@Project23D.com> wrote:

Luc,

The items in simpleusb-tune-menu are the step by step.

Be not afraid to use a little intuition. Your changes are not saved until you execute a command *IN* the simpleusb-tune-menu, of which I am going to let you figure out.

While not always obvious, the ASL box mutes DTMF, so you cannot use that. There is a reason why a 1KHz tone at 3KHz deviation is used. Try to whistle to as close to 1KHz as possible!..

It is best to use a calibrated service monitor for getting accurate audio levels, first thing it keeps your node radio in spec. The other thing is it keeps the audio nice and clean. Find a friend in the area with a service monitor and have him/her teach you how to appreciate why it must be used when adjusting audio levels used in radio.

The values metered on the RX level scale are accurate, so when the RX deviation meter on the simpleusb-tune-menu says you are at 3KHz deviation, then you are at 3KHz deviation... provided that signal you are putting into the node radio is *actually* transmitting at 1KHz tone at 3KHz deviation. Read the aforementioned paragraph.

Benjamin, KB9LFZ

...

On Thu, 2017-07-27 at 06:34 -0400, Luc Drolet VE2 LUQ wrote: Hello everyone,

With an RPi, can you tell me how we can do to adjust the audio with a monitor service,

With PuTTY, I can see, "12 - Run simpleusb_tune_Menu Apllication" And then, yes, I saw "2 RX VOICE Level Set" but I do not know how to change my value and also save it Is there a step-by-step procedure for AllStar Link,

RX VOICE TX VOICE

thank you very much and Have a Nice day Luc 73 _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.