Thanks for the GSM files. So, OK. First, are you sure that 10.0.1.1 is the address assigned to your

node computer and not to the Airport router? Usually, the address at then eginning of a block like that is the router. So you’re likely trig to ssh to the wrong place. Do you have direct access to the node computer, i.e. is there a keyboard and monitor on it? If so, you should be able to find your correct internal IP by typing ifconfig eth0

Thanks! I typed ifconfig eth0 and I was 10.0.1.23!! Stupid ME I Was not even port forwarding to the right address! I have no idea how it worked even to a few nodes without port forwarding but 28298 works now as well as the web transciever! On Fri, Apr 18, 2014 at 3:53 PM, Skyler F <electricity440@gmail.com> wrote:

I meant to reply all, sorry if you recieve this twice

On Fri, Apr 18, 2014 at 3:53 PM, Skyler F <electricity440@gmail.com>wrote:

...

Stupid ME I Was not even port forwarding to the right address! I have no idea how it worked even to a few nodes without port forwarding but 28298 works now as well as the web transciever!

On Fri, Apr 18, 2014 at 3:33 PM, Skyler F <electricity440@gmail.com>wrote:

...

Thanks for the GSM files.

So, OK. First, are you sure that 10.0.1.1 is the address assigned to

...

your node computer and not to the Airport router? Usually, the address at then eginning of a block like that is the router. So you’re likely trig to ssh to the wrong place. Do you have direct access to the node computer, i.e. is there a keyboard and monitor on it? If so, you should be able to find your correct internal IP by typing ifconfig eth0

Thanks! I typed ifconfig eth0 and I was 10.0.1.23!!

On Fri, Apr 18, 2014 at 1:51 PM, Fred McLean <FredM@fredsportraits.com>wrote:

...

Skyler, (copy of the email I just sent to the group with two attached gsm files)

If you learn the trick to convert a Microsoft wav to ULAW, please let me know!

I convert or create the wav file top 8000 just as you do. Instead of worrying much about ULAW files I just convert it to a gsm file.

To convert a 16000 or 8000 Hz wav to gsm. (I think it will work with both)

Use the command line, not the CLI.

Go to the directory where your newly copied wav file is located.

Type in the following command to change to that directory.

The below example is assuming you create a folder named “custom”.

cd /var/lib/asterisk/sounds/custom

Your prompt should look similar to this. w0fcm is my server name.

[root@w0fcm custom]#

Input the following command substituting your wav file name and your new gsm file name.

Here I used the name example.wav and example.gsm.

sox example.wav -r 8000 example.gsm

Delete the wav file and any ulaw or sln files with the same prefix in the folder you are working with.

If you want to play a file locally input the following command.

Note: 29503 is the node number I am playing it on.

/usr/sbin/asterisk -rx "rpt localplay 29503 custom/example"

If you want to play a sound file globally input the following command.

/usr/sbin/asterisk -rx "rpt playback 29503 custom/example"

To replace a tone with a sound file just remove or comment out the codes and replace it with a folder and file prefix. Below are three examples of tones/sounds I use for remotetx.

[telemetry]

remotetx=custom/beep

;remotetx=custom/screen

;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000); Original

;remotetx=|t(1800,100,120,3000)(1300,100,120,3000)(1750,100,120,3000)(1000,100,120,3000); Star Trek

;remotetx=|t(1173,100,120,3000)(1316,100,120,3000)(1045,100,120,3000)(523,100,120,3000)(783,100,120,3000); Close Encounters

Let me know if you have any questions.

73

Fred McLean

w0fcm 29503

*From:* Skyler Fennell [mailto:electricity440@gmail.com] *Sent:* Friday, April 18, 2014 12:07 PM *To:* Mark Johnston *Cc:* app_rpt-users@ohnosec.org *Subject:* Re: [App_rpt-users] Changing Courtesy Tones, and SSHing into the computer

I did not restart the sshd after I changed port 222 to 22. I did reboot the computer, but Maybe that's not enough. So just run "/etc/rc3.d/S55sshd restart"?

I got really confused with all of those random numbers under telemetry section, but I guess they are all frequencies for the Courtesy tone.

On audacity, I just did file > export then I chose other uncompressed format and did Microsoft wav, ULAW. I also made sure the project rate was at 8000.

When I get home, I will check the files, and test the telephone portal.

73 (or *72 in allstar)

Skyler Kd0whb

Sent from my iPhone

On Apr 18, 2014, at 10:22 AM, Mark Johnston <markjohnston73@gmail.com> wrote:

SSH: I assume you restarted the sshd after changing the port or reboot the allstar box either way - /etc/rc3.d/S55sshd restart

should do it.

Btw what is the trick to getting uLaw files via Audacity?

Courtesy tones, have to look under the [Telemetry] section

and change the freq/numbers there -

in /etc/asterisk/rpt.conf

do you have the line in rpt.conf?

<node> = radio@127.0.0.1/<node>,NONE

And the one in /etc/asterisk/iax.conf

register=<node>:<secret>@register.allstarlink.org

Assuming the port 4569 is setup correctly, can you connect from the allstar dial in # from any std telephone?

"Got Root?"

How many software engineers does it take to change a light bulb?

*None. It's a hardware problem.*

Unix is user friendly. It's just very particular about who it's friends are.

WINDOWS: Will Install Needless Data On Whole System

MICROSOFT: Most Intelligent Customers Realize Our Software Only Fools Teenagers.

A ntennas P oorly P laced L acks E ngineering

The best way to accelerate a computer running Windows is at 9.81 m/s².

*"I get paid to support Windows, I use Linux to get work done."*

On Fri, Apr 18, 2014 at 7:14 AM, Skyler F <electricity440@gmail.com> wrote:

Hello,

I am new ham in high school, and finally got a little SIMPLEX repeater up and running.

*My first question* Is about SSHing into the computer remotely. I first gave it a try on my LAN, because I knew port forwarding would not be required.

First, I *Changed *the port 222 to port 22 on the SSHD_Config file

We are using an apple airport router, which states the LAN address of the Ethernet port is 10.0.1.1. I typed ssh root@10.0.1.1, and I got a connection refused.

I was able to reverse SSH back to my macintosh using ssh username@computersLANip from ACID, but when I tried to SSH back to acid, it would not work. Just Connection Refused.

After I login on ACID it says Root@Skylersnode, my node, and I also gave ssh root@<node number> and ssh skylersnode@local IP a try, but still no success.

Are there any suggestions on getting this to work?

*Second question: Courtesy tones,*

I just figured out how to create a ULAW on audacity, and mount a flash drive on the command, and I am wondering if I can change the courtesy tones or any other audio file. Like the "I OWN COMMAND" annoying thing. Where would the courtesy tones be located, and under what file name?

*Third question: *why it wont work on the web transceiver

When I dial in the node on the web transceiver, nothing happens, and when I hit the connect button, it does not do anything. Is there any way to get it to work, or will the web transceiver not work with my node. I would think it should work, because I have almost the same setup as Willem's node, 29571<https://allstarlink.org/portal/webtransceiver-frameset.php?nodenum=29571>,on saddle back mountain.

*Last Question: Won't connect to 28298 or 28299*

This node is part of the FUN system here in Colorado, and I tried dialing 28298, which belongs to Jeff KØJSC, but I heard nothing, not even the change in courtesy tone. He has no idea why my node will not connect up, but it is weird because it won't even show up on the web transceiver.

Thanks

Skyler KDØWHB

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.