[App_rpt-users] limey and parallel port

[Tim Sawyer]

Are you saving the configuration after you make changes? Limey Linux loads everything from the CF card into ram when it boots. Any changes you make need to be saved to the CF card with the command svcfg.
--
Tim
:wq

On Sep 4, 2012, at 9:53 PM, KB7RSI <kb7rsi at gmail.com> wrote:

> Well, one thing I did notice that is contributing to my issue is,
> every time i reboot my system, I end up with both usbradio.conf and
> simpleusb.conf files.  Also, If I delete these files and reboot, they
> re-appear, and if I do modify either one of those files and reboot,
> they end up being overwritten loosing any changes that i have made.
> Not really sure of what happening here.
> 
> Thanks
> 
> Harold
> 
> On Tue, Sep 4, 2012 at 8:57 PM, Tim Sawyer <tim.sawyer at me.com> wrote:
>> It works on Limey Linux. We're using it in a number of nodes. Here's the
>> simpleusb.conf from one of my nodes:
>> 
>> [general]
>> 
>> [usb]
>> 
>> pp2 = ptt
>> pp3= out0
>> pp10 = cor
>> 
>> eeprom=0
>> 
>> hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using
>> ; the instructions from usbfob.pdf. Use a setting of
>> ; 1 is for Dingotel/Sph interfaces.
>> 
>> rxboost=0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
>> ; Set to 1 for additonal gain if using a low-level receiver output
>> 
>> ;carrierfrom=ppinvert ; no,usb,usbinvert
>> carrierfrom=pp ; no,usb,usbinvert
>> ; no - no carrier detection at all
>> ; usb - from the COR line on the modified USB sound fob
>> ; usbinvert - from the inverted COR line on the modified USB sound fob
>> 
>> ctcssfrom=no ; no,usb,usbinvert
>> ; no - CTCSS decoding, system will be carrier squelch
>> ; usb - CTCSS decoding using input from USB FOB
>> ; usbinvert - from the inverted CTCSS line on the modified USB sound fob
>> 
>> txmixa=voice ; Left channel output: no,voice,tone,composite,auxvoice
>> ; no - Do not output anything
>> ; voice - output voice only
>> 
>> txmixb=no ; Right channel output: no,voice,tone,composite, auxvoice
>> ; See txmixa above.
>> 
>> invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit
>> ; This is the collector lead of the 2n4401 on the modified
>> ; usb sound fob.
>> ; please refer to the howto for the procedure to do this.
>> 
>> duplex=1 ; Full Duplex
>> plfilter=yes
>> 
>> --
>> Tim
>> :wq
>> 
>> On Sep 4, 2012, at 7:14 PM, KB7RSI <kb7rsi at gmail.com> wrote:
>> 
>> Also, im not sure that this applies to limey linux.
>> 
>> Thanks
>> 
>> On Tue, Sep 4, 2012 at 7:13 PM, KB7RSI <kb7rsi at gmail.com> wrote:
>> 
>> Ok thanks for that info.
>> I guess limey does not totally support my via motherboard.
>> It will not address my parallel port for some reason.
>> 
>> Thanks again.
>> 
>> Harold
>> 
>> On Tue, Sep 4, 2012 at 5:46 PM, Tim Sawyer <tim.sawyer at me.com> wrote:
>> 
>> http://ohnosec.org/drupal/node/177
>> --
>> Tim
>> :wq
>> 
>> On Sep 4, 2012, at 5:14 PM, KB7RSI <kb7rsi at gmail.com> wrote:
>> 
>> Hello all.
>> Does anyone know what the parallel port is called in dev folder in
>> limey linux if its even available?
>> Im trying to use my parallel port for keying and COR for my radio.
>> 
>> Thanks
>> 
>> Harold
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>> 
>> 
>> 
>> 
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at ohnosec.org
>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>