[App_rpt-users] Dual PL Tone? Possible?

[Johnny Keeker]

Jon;
Do you know how the following cop commands effect your multi-tone setup? 
JK

From: Jon Rorke <jrorke at cogeco.ca>
To: 
Cc: app_rpt mailing list <App_rpt-users at ohnosec.org> 
Sent: Wednesday, November 6, 2013 1:23 PM
Subject: Re: [App_rpt-users] Dual PL Tone? Possible?



Hmm, mine seems to work as I described. But I seem to remember that i had to do an update from the SVN to get it to work right. 
Unless of course something got changed in the newer sw since then.
Jon VA3RQ

On 11/6/2013 12:43 PM, Bob Roszkowski wrote:

Hello Jon,
>I did try what you mentioned and was able to get the repeater to key up on two different PL tones. However, both tones did key up the link. I matched all parameters in the usbradio.conf file and restarted. 
>Any ideas?
>boB W5EVH
>On Nov 6, 2013 6:57 AM, "Jon Rorke" <jrorke at cogeco.ca> wrote:
>
>Yes App_Rpt does support multi tone. I have done it. 
>>
>>If you use the defined default tone then your signal goes out over the repeater and any links connected. 
>>
>>If you use one of the alternate tones defined then only the repeater works locally and your signal doesnt not go out on any connected links.
>>
>>[usbNODE#]
>>
>>hdwtype=0    
>>rxboost=1
>>txboost=1
>>rxctcssrelax=1
>>txctcssdefault=103.5
>>rxctcssfreqs=103.5,136.5,156.7
>>txctcssfreqs=103.5,136.5,156.7
>>;rxctcssoverride=0
>>;carrierfrom=usbinvert
>>carrierfrom=dsp
>>;ctcssfrom=no
>>ctcssfrom=dsp
>>rxdemod=flat
>>txprelim=yes
>>txlimonly=no
>>txtoctype=phase
>>txmixa=composite
>>txmixb=no
>>invertptt=0
>>duplex=1
>>rxondelay=0
>>rxnoisefiltype=0
>>eeprom=0
>>
>>#includeifexists custom/usbradio.conf
>>
>>From the above example from usbradio.conf you can see that the default tone is 103.5 but it will aslo work on 136.5 and 156.7. 
>>
>>But if you use the non default tones it only works in local mode.
>>
>>Jon VA3RQ
>>
>>
>>
>>
>>
>>On 11/5/2013 11:02 PM, Robert A. Poff wrote:
>>
>>While it won't selectively route to network or local only, you can use multiple tones.
>>>
>>>Operating like a community repeater.
>>>
>>>In usbradio.conf (urd.conf for XIPAR), on the rxctcssfreqs and txctcssfreqs lines put the additional tones separated by commas.
>>>
>>>These of course need to be standard PL frequencies.
>>>
>>>Last year we needed to transition from 123.0 to 146.2. Ran both PLs for two months.
>>>
>>>
>>>-- 
>>>Sent from my Android phone with K-9 Mail. 
>>>Please excuse my brevity and typing errors. 
>>> 
>>>
>>>_______________________________________________
App_rpt-users mailing list App_rpt-users at ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users 
>>
>>_______________________________________________
>>App_rpt-users mailing list
>>App_rpt-users at ohnosec.org
>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>>


_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users



 56 - Rx CTCSS Enable
 57 - Rx CTCSS Disable
 58 - Tx CTCSS On Input only Enable
 59 - Tx CTCSS On Input only Disable
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20131106/92a0311e/attachment.html>