[App_rpt-users] URI and URIx Testing

Bob kk6ecm at gmail.com
Sat Apr 26 01:37:17 UTC 2014


Most recent ACID distro from Allstarlink.org. Gigabyte C1007UN-D with 4 gig
memory, and an SSD SATA drive.

 

Built in with an IntelR Dual-core CeleronR 1007U processor (1.5 GHz)

 

lsusb -v reports the URI and the URIx both as USB 1.1

 

Thanks,

Bob

kk6ecm

 

  _____  

From: Chris Andrist [mailto:chris at yeahmon.net] 
Sent: Friday, April 25, 2014 6:02 PM
To: Bob
Subject: Re: [App_rpt-users] URI and URIx Testing

 

Bob,

 

Tell us about the computer you are running this on and what Distro you are
using?

 

Just as an FYI. ACID runs best on Pentium 4 computers and slower.

 

--

Regards,

 

Chris Andrist, KC7WSU


On Apr 25, 2014, at 6:59 PM, "Bob" <kk6ecm at gmail.com> wrote:

I'm at a loss... looking for ideas on how to proceed... Still attempting to
get our repeater working... rebuilt the computer that crashed, and it works
well... Getting strange results when connecting the URI back to the radio
(can't find anything wrong there). The fact I can't seem to get a URI, or
URIx working with my computer suggests a possible issue with my setup. I
have some inputs from folks for changes in the usbradio, or simpleusb which
I'd like to check, but need to confirm the URI is working correctly, so I'm
not chasing hardware issues by looking at software.

 

I tested my URI using the loopback diagram and uridiag; it passes all the
digital, and fails all the analog. I procured a URIx for replacement, and
built up the loopback connector for it and tested, same results. I've
checked and rechecked my wiring of the loopback connector. The URIx uses two
1k resistors and two extra jumpers than the URI (see below), and the URI two
10k resistors per DMK folks. (There is a confirmed error in the uridiag
listed connections). I did not connect the URIx 12 and 20 (Blk and Wht)
leads, nor the power supply to activate the 2x amplifier (pins 13 & 25),
which I am not using. I'm told the correct connections are as shown below
from the URI-FAQ.pdf, with change of 1K for 10K for URIx per DMK, and
comparing with the URIx test fixture.

 

Assuming the URIx was good from the factory, and all I did was 

connect it up to the loopback and computer, 

turn on the computer with ACID 

# service asterisk stop

# uridiag

 

URIDiag, diagnostic program for the DMK Engineering URI

USB Radio Interface, version 0.8, 04/26/11

 

Found CM119 USB Radio Interface at 001/003

.

.

.

Enter your selection:t

Testing digital I/O (PTT,COR,TONE and GPIO)....

Digital I/O passed!!

Testing Analog at 204 (and 700) Hz...

Analog level on left channel for 204.0 Hz (0.0) is out of range!!

.

.

.

 

24 Error(s) found during test(s)!!!!

 

 

URI

 

Pin 1 to Pin 7

Pin 2 to Pin 3

Pin 4 to Pin 8

Pin 23 to Pin 24

10K Resistor between Pins 21 and 22

10K Resistor between Pins 21 and 23

 

URIx

 

Pin 1 to Pin 7

Pin 2 to Pin 3

Pin 4 to Pin 8

Pin 23 to Pin 24

1K Resistor between Pins 21 and 22

1K Resistor between Pins 21 and 23

Pin 5 to Pin 10

Pin 6 to Pin 11

 

 

sigh!

 

Thanks,

Bob

kk6ecm

_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem. 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140425/205222dc/attachment.html>


More information about the App_rpt-users mailing list