[App_rpt-users] audio radio to internet issue

[REDBUTTON_CTRL]

If this is your usb radio.conf file then it is missing a couple of things.

You need the following:

carrierfrom=usb (or usbinvert if your cor is active low)

and the rxdemod must be set to speaker or flat

That should get tit listening to rx audio to start.

Jon VA3RQ

On 2/8/2014 5:31 PM, ea8ee wrote:
> usb27305
> rxboost=1
> txboost=1
> rxctcssrelax=1
> txctcssdefault=88.5
> rxctcssfreqs=88.5
> ;rxctcssoverride=0
> ctcssfrom=usb
> rxdemod=no
> txprelim=no
> txlimonly=no
> txtoctype=notone
> txmixa=composite
> txmixb=composite
> invertptt=0
> duplex=0
> rxondelay=o
> rxnoisefiltype=0
> eeprom=1
>
> The DMK works nice in TX but in RX not receive nothing
>
>
>
> 2014-02-08 20:02 GMT+00:00 Doug Crompton <doug at crompton.com 
> <mailto:doug at crompton.com>>:
>
>     I think it found your adapter as you said you had audio in one
>     direction. If not see below.
>
>     Did you select the active usb device in the config utility before
>     you tried to make changes?
>
>
>     If the adapter is not being found at all try this....
>
>     The following USB interfaces are defined in usbradio -
>
>     #define C108_VENDOR_ID          0x0d8c
>     #define C108_PRODUCT_ID         0x000c
>     #define C108AH_PRODUCT_ID       0x013c
>     #define C119_PRODUCT_ID         0x0008
>     #define C119A_PRODUCT_ID        0x013a
>     #define N1KDO_PRODUCT_ID        0x6a00
>     #define C108_HID_INTERFACE      3
>
>     When you boot up you should see one of these initialized in the
>     messages. After boot do -
>
>     dmesg | more
>
>     and page through and see if it found your adapter.
>
>     I am using the DMK and it looks like this -
>
>     [root at WA3DSP_Allstar wa3dsp]# dmesg | grep Sound
>     input: C-Media Electronics Inc.       USB PnP Sound Device as
>     /class/input/input0
>     input,hidraw0: USB HID v1.00 Device [C-Media Electronics
>     Inc.       USB PnP Sound Device] on usb-0000:00:1d.0-1
>
>     *73 Doug
>     WA3DSP
>     http://www.crompton.com/hamradio*
>
>
>     ------------------------------------------------------------------------
>     From: ea8ee1 at gmail.com <mailto:ea8ee1 at gmail.com>
>     Date: Sat, 8 Feb 2014 19:14:56 +0000
>     To: app_rpt-users at ohnosec.org <mailto:app_rpt-users at ohnosec.org>
>     Subject: Re: [App_rpt-users] audio radio to internet issue
>
>
>     I tried with  cli and radio tune rxnoise and the pc says the
>     device usb27305 currectly not active ! any suggestion?
>
>
>     2014-02-08 8:51 GMT+00:00 jose <ea8ee1 at gmail.com
>     <mailto:ea8ee1 at gmail.com>>:
>
>         Hi Doug! the ptt and audio from internet to radio works nicely
>         the problem is about the audio from radio to internet not
>         audio neither the node receive the dmtf from radio or
>         webstransceiver
>
>         El 08/02/2014 6:31, Doug Crompton escribió:
>
>             You need to set -
>
>             duplex=1  ; Simplex, no telelmetry
>             duplex=0  ; Simplex, telelmetry
>
>             in rpt.conf if you are running simplex.
>
>             Also make sure the polarity is correct in your usbradio or
>             simpleusb file for the PTT and COS if you are using it.
>
>
>
>
>     _______________________________________________ App_rpt-users
>     mailing list App_rpt-users at ohnosec.org
>     <mailto:App_rpt-users at ohnosec.org>
>     http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To
>     unsubscribe from this list please visit
>     http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and
>     scroll down to the bottom of the page. Enter your email address
>     and press the "Unsubscribe or edit options button" You do not need
>     a password to unsubscribe, you can do it via email confirmation.
>     If you have trouble unsubscribing, please send a message to the
>     list detailing the problem.
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20140208/8038dcb0/attachment.html>