[App_rpt-users] usbradio_tune_xxxxx.conf where .conf =.confusion

[kk6ecm]

Ah yes... DIAL is a bit different than ACID.

 

For DIAL I get

Bus 001 Device 004: ID 0d8c:013a C-Media Electronics, Inc.

 

and 

 

devstr=1-1.4:1.0

 

but this works also

 

devstr=1-4

 

Don't know.

 

Bob

kk6ecm

73

 

  _____  

From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Steve Agee
Sent: Saturday, May 21, 2016 2:05 PM
To: app_rpt-users at ohnosec.org
Subject: Re: [App_rpt-users] usbradio_tune_xxxxx.conf where .conf
=.confusion

 

Yup, tried that early on with no luck. Then tried using the (W) command in
both radio-tune-menu or simpleusb-tune-menu. The <bus>-<dev> listed in the
tuning files does not match what the "lsusb" command reports. Well, the
<bus> matches, but NOT the <dev>. On a working ACID install under same
conditions, I have two (count them two) different tuning files where
"devnum=3" go figure, and it works!
N5ZUA

On 5/21/2016 3:55 PM, kk6ecm wrote:

run lsusb at the command line, then set devstr=<bus>-<device> for the
device(s) shown. Your example is for Bus 004 Device 002.

 

Bob

kk6ecm

73

 


  _____  


From: app_rpt-users-bounces at ohnosec.org
[mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Steve Agee
Sent: Saturday, May 21, 2016 12:05 PM
To: app_rpt-users at ohnosec.org
Subject: [App_rpt-users] usbradio_tune_xxxxx.conf where .conf = .confusion

 

Hello list:

I've searched 

  <http://www.xelatec.com/xipar/node/180>
<http://www.xelatec.com/xipar/node/180> 

and I fully understand the description/explanations given. What I don't
understand, with specific attention to the lines:

; name=usb ;
; devnum=1 ;
devstr=4-2 ;

is how to manually uncomment, and manipulate them. In this particular
instance, I'm trying to get a DIAL box running with one original URI (early
version) using the USBRADIO channel driver, and one URIX (newer version)
using the SIMPLEUSB channel driver. I've followed the step-by-step (or was
that Crossbar 5 Duude?) instructions for starting off with a single node,
then adding the second node. That simply doesn't work. The second URIx green
L.E.D. stays solid throughout the process. Are these lines provided for
informational purposes only, or can they be edited to force the second
device to be recognized and assigned?

N5ZUA






_______________________________________________
App_rpt-users mailing list
App_rpt-users at ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
 
To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to
the bottom of the page. Enter your email address and press the "Unsubscribe
or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem. 

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20160521/e5591734/attachment.html>