[App_rpt-users] App_rpt-users Digest, Vol 91, Issue 5

Fri Sep 2 18:54:47 UTC 2016

in rpt.conf under the [nodes] stanza you'd want somthing like this

1234 = radio at 10.0.0.x:4569/1234,NONE
1235 = radio at 10.0.0.x:4569/1235,NONE

That would be the IP and node number of the remote node(s)

You'd also want to comment out the register stuff in iax.conf so private
nodes don't try to register with the public allstar server.

On Fri, Sep 2, 2016 at 12:49 PM, <app_rpt-users-request at ohnosec.org> wrote:

> Send App_rpt-users mailing list submissions to
>         app_rpt-users at ohnosec.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
>         http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> or, via email, send a message with subject or body 'help' to
>         app_rpt-users-request at ohnosec.org
>
> You can reach the person managing the list at
>         app_rpt-users-owner at ohnosec.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of App_rpt-users digest..."
>
>
> Today's Topics:
>
>    1. Re: help with reverse patch setup (mike at midnighteng.com)
>    2. Private nodes not connecting (N6GKJ Land)
>    3. Re: Private nodes not connecting (Corey Dean)
>    4. Re: Private nodes not connecting (Steve Zingman)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 2 Sep 2016 13:28:00 -0400
> From: mike at midnighteng.com
> To: app_rpt-users at ohnosec.org
> Subject: Re: [App_rpt-users] help with reverse patch setup
> Message-ID:
>         <5a9b0d6ed092135ac8bc437002d93094.squirrel at webmail.midnighteng.com
> >
> Content-Type: text/plain;charset=iso-8859-1
>
>
> While not everyone has the same thing in mind when they use the words
> REVERSE PHONE
> PATCH, I'll gamble on your meaning/need...
>
> The last line where you are making the actual switch(connection) to the
> radio
> interface has to be defined in the same context it is being switch to.
> So if it is playing back the digits as per your stanza and not making the
> connection (dropping the call/falling through) ,
> The last line should look something like this...
>
> exten => 29283,n,Rpt,29283|P
>
> See notes on the "P" designation of documentation but
> I think it is stated as "Phone Control Mode"
> and there are other modes depending on use/need.
> And the character just before it is a command separator,
> don't confuse it with others.
>
> ...mike/kb8jnm
>
>
>
> > While attempting to create a reverse patch a incoming call returns the
> following
> > [Sep ??2 06:54:04] NOTICE[859]: chan_iax2.c:9471 socket_process:
> Rejected connect
> > attempt from 10.xxx.xxx.xxx, request '29883 at radio-control' does not
> exist
> >
> >
> >
> > extensions.conf is configured??
> > [radio??control]exten => 29883,1,Answerexten =>
> 29883,n,Playback,rpt/nodeexten =>
> > 29883,n,Playback,digits/2exten => 29883,n,Playback,digits/9exten =>
> > 29883,n,Playback,digits/8exten => 29883,n,Playback,digits/8exten =>
> > 29883,n,Playback,digits/3exten => 29883,n,Rpt,29883|D
> > iax.conf is configured
> >
> > [N6LXX-IN]type=friendauth=md5secret=XXXXXXXXXXXXXXdisallow=
> allallow=ulawallow=gsmcodecpriority=hostcontext=radio-controltransfer=no
> > CLI> show dialplan returns (edited)
> >
> > [ Context 'radio??control' created by 'pbx_config' ]?? '29883' => ?? ??
> ?? ??1.
> > Answer() ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ??
> [pbx_config]?? ?? ?? ??
> > ?? ?? ?? ?? ?? ?? 2. Playback(rpt/node) ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ??
> ??
> > [pbx_config]?? ?? ?? ?? ?? ?? ?? ?? ?? ?? 3. Playback(digits/2) ?? ?? ??
> ?? ?? ??
> > ?? ?? ?? ?? ?? ?? [pbx_config]?? ?? ?? ?? ?? ?? ?? ?? ?? ?? 4.
> Playback(digits/9)
> > ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? [pbx_config]?? ?? ?? ?? ?? ?? ?? ??
> ?? ?? 5.
> > Playback(digits/8) ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? [pbx_config]?? ??
> ?? ?? ??
> > ?? ?? ?? ?? ?? 6. Playback(digits/8) ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ??
> > [pbx_config]?? ?? ?? ?? ?? ?? ?? ?? ?? ?? 7. Playback(digits/3) ?? ?? ??
> ?? ?? ??
> > ?? ?? ?? ?? ?? ?? [pbx_config]?? ?? ?? ?? ?? ?? ?? ?? ?? ?? 8.
> Rpt(29883|D) ?? ??
> > ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? ?? [pbx_config]
> >
> > CLI> dialplan show 29883 at radio-controlThere is no existence of
> 'radio-control'
> > context
> > Any help greatly appreciated
> > Chris
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll
> down to the
> > bottom of the page. Enter your email address and press the "Unsubscribe
> or edit
> > options button"
> > You do not need a password to unsubscribe, you can do it via email
> confirmation. If
> > you have trouble unsubscribing, please send a message to the list
> detailing the
> > problem.
>
>
>
>
> ------------------------------
>
> Message: 2
> Date: Fri, 2 Sep 2016 11:23:51 -0700
> From: N6GKJ Land <n6gkj1 at gmail.com>
> To: App RPT Users <app_rpt-users at ohnosec.org>
> Subject: [App_rpt-users] Private nodes not connecting
> Message-ID:
>         <CANr-_9p6m7i=entjW__WxVFz=9ieb_s3K9Vnax8TtRoJrfRZ=g@
> mail.gmail.com>
> Content-Type: text/plain; charset="utf-8"
>
> Hi guys,
>
> I have 2 RPI 3 servers running the latest N4IRS release. I have a private
> node on each server.
>
> RPI3 #1 is 10.0.0.200 NODE 1000:4568
> RPI3 #2 is 10.0.0.201 NODE 1001:4569
>
> Neither node can connect to the other. I am using the CLI inside the
> asterisk program to manually connect using
> rpt fun 1000 *31001 from server 1
>
> or
>
> rpt fun 1001 *31000 from server 2
>
> Listed here is how the scripts are defined.
>
> extensions.conf
> RPI3 #1
> [globals]
> HOMENPA = 209 ; change this to your Area Code
> NODE = 1000   ; change this to your node number
>
> [default]
>
> exten => i,1,Hangup
>
> RPI3 #2
> [globals]
> HOMENPA = 209 ; change this to your Area Code
> NODE = 1001   ; change this to your node number
>
> [default]
>
> exten => i,1,Hangup
>
> [radio-secure]
> exten => ${NODE},1,rpt,${NODE}
>
> [radio-secure]
> exten => ${NODE},1,rpt,${NODE}
>
>
> rpt.conf
>
> RPI3 #1
> rxchannel = dahdi/pseudo
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a definition
> ; for your local nodes, and private (off of allstar link) nodes here.
>
> 1000 = radio at 127.0.0.1
> <https://us-mg6.mail.yahoo.com/compose?to=radio@127.0.0.1>:4568/1000,NONE
> ; This must be changed to your node number
> 1001 = radio at 10.0.0.201
> <https://us-mg6.mail.yahoo.com/compose?to=radio@10.0.0.201>:4569/1001,NONE
> ; and iax port number if not the default
>
> RPI3 #2
>
> rxchannel = dahdi/pseudo
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a definition
> ; for your local nodes, and private (off of allstar link) nodes here.
>
> 1000 = radio at 10.0.0.201
> <https://us-mg6.mail.yahoo.com/compose?to=radio@10.0.0.201>:4568/1000,NONE
> ; This must be changed to your node number
> 1001 = radio at 127.0.0.1
> <https://us-mg6.mail.yahoo.com/compose?to=radio@127.0.0.1>:4569/1001,NONE
> ; and iax port number if not the default
>
>
> I am not having any results with this. I did not uncomment node register
> line in iax.conf for either server
> and also in rpt,conf I did not uncomment the status report lines
>
> I just simply want these two servers to talk to each other on the same lan
>
> The nodes in both of these servers are HUBS.
> Anyone have any ideas I have over looked?
>
> Ron Simpson,
> N6GKJ Amateur Radio
> ...................
>
>
> Have you ever noticed that when you are looking for something,
> it is always found in the last place you look?
> Ron Simpson,
> N6GKJ....
> Amateur Radio
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/
> 20160902/1f40f1b5/attachment-0001.html>
>
> ------------------------------
>
> Message: 3
> Date: Fri, 2 Sep 2016 14:45:43 -0400
> From: Corey Dean <n3fe at repeater.net>
> To: N6GKJ Land <n6gkj1 at gmail.com>
> Cc: App RPT Users <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] Private nodes not connecting
> Message-ID: <23CED29E-BF1A-4A70-A4B3-0FE5709F0FC1 at repeater.net>
> Content-Type: text/plain; charset="us-ascii"
>
> You have to define each node in the other node.  Once I am back to my
> office I will send you an example of someone does t beat me to it
>
> Sent from my iPhone
>
> > On Sep 2, 2016, at 2:23 PM, N6GKJ Land <n6gkj1 at gmail.com> wrote:
> >
> > Hi guys,
> >
> > I have 2 RPI 3 servers running the latest N4IRS release. I have a
> private node on each server.
> >
> > RPI3 #1 is 10.0.0.200 NODE 1000:4568
> > RPI3 #2 is 10.0.0.201 NODE 1001:4569
> >
> > Neither node can connect to the other. I am using the CLI inside the
> asterisk program to manually connect using
> > rpt fun 1000 *31001 from server 1
> >
> > or
> >
> > rpt fun 1001 *31000 from server 2
> >
> > Listed here is how the scripts are defined.
> >
> > extensions.conf
> > RPI3 #1
> > [globals]
> > HOMENPA = 209 ; change this to your Area Code
> > NODE = 1000   ; change this to your node number
> >
> > [default]
> >
> > exten => i,1,Hangup
> >
> > RPI3 #2
> > [globals]
> > HOMENPA = 209 ; change this to your Area Code
> > NODE = 1001   ; change this to your node number
> >
> > [default]
> >
> > exten => i,1,Hangup
> >
> > [radio-secure]
> > exten => ${NODE},1,rpt,${NODE}
> >
> > [radio-secure]
> > exten => ${NODE},1,rpt,${NODE}
> >
> >
> > rpt.conf
> >
> > RPI3 #1
> > rxchannel = dahdi/pseudo
> >
> > [nodes]
> > ; Note, if you are using automatic update for allstar link nodes,
> > ; no allstar link nodes should be defined here. Only place a definition
> > ; for your local nodes, and private (off of allstar link) nodes here.
> >
> > 1000 = radio at 127.0.0.1:4568/1000,NONE    ; This must be changed to your
> node number
> > 1001 = radio at 10.0.0.201:4569/1001,NONE  ; and iax port number if not
> the default
> >
> > RPI3 #2
> >
> > rxchannel = dahdi/pseudo
> >
> > [nodes]
> > ; Note, if you are using automatic update for allstar link nodes,
> > ; no allstar link nodes should be defined here. Only place a definition
> > ; for your local nodes, and private (off of allstar link) nodes here.
> >
> > 1000 = radio at 10.0.0.201:4568/1000,NONE    ; This must be changed to
> your node number
> > 1001 = radio at 127.0.0.1:4569/1001,NONE  ; and iax port number if not the
> default
> >
> >
> > I am not having any results with this. I did not uncomment node register
> line in iax.conf for either server
> > and also in rpt,conf I did not uncomment the status report lines
> >
> > I just simply want these two servers to talk to each other on the same
> lan
> >
> > The nodes in both of these servers are HUBS.
> > Anyone have any ideas I have over looked?
> >
> > Ron Simpson,
> > N6GKJ Amateur Radio
> > ...................
> >
> >
> > Have you ever noticed that when you are looking for something,
> > it is always found in the last place you look?
> > Ron Simpson,
> > N6GKJ....
> > Amateur Radio
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at ohnosec.org
> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/
> mailman/listinfo/app_rpt-users and scroll down to the bottom of the page.
> Enter your email address and press the "Unsubscribe or edit options button"
> > You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/
> 20160902/a7a7a0b0/attachment-0001.html>
>
> ------------------------------
>
> Message: 4
> Date: Fri, 2 Sep 2016 14:49:25 -0400
> From: Steve Zingman <szingman at msgstor.com>
> To: N6GKJ Land <n6gkj1 at gmail.com>, App RPT Users
>         <app_rpt-users at ohnosec.org>
> Subject: Re: [App_rpt-users] Private nodes not connecting
> Message-ID: <1bf49de9-e665-0ce5-2c58-4641ce19cb96 at msgstor.com>
> Content-Type: text/plain; charset="windows-1252"; Format="flowed"
>
> Ron,
> set debug:
> rpt debug level 7
>
> rpt fun 1000 *31001 from server 1
> or
> rpt fun 1001 *31000 from server 2
>
> What is the output?
>
> --
> "Just say no to world domination"
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://ohnosec.org/pipermail/app_rpt-users/attachments/
> 20160902/f69214f4/attachment.html>
>
> ------------------------------
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>
>
> End of App_rpt-users Digest, Vol 91, Issue 5
> ********************************************
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20160902/c3d97513/attachment.html>