[App_rpt-users] ctcss Encode Issues
Neil k8it
k8it at cac.net
Wed Aug 9 17:01:22 UTC 2017
that could be a option, configurable
Thanks
73 Neil Sablatzky K8IT
Allstar Node 41838 KITLINK
Allstar Node 42087 KITLINK HUB
IRLP Node exp0068
Echolink K8IT-L
WIRES-X K8IT 11479 Room 21479
From: Steve Mahler
Sent: Wednesday, August 09, 2017 12:21 PM
To: app_rpt-users at lists.allstarlink.org
Subject: Re: [App_rpt-users] ctcss Encode Issues
Neil:
Understood. As long as you are thinking about a code change ... should the PL tone be held thru the tailmessage system too?
...STeve
On 8/9/2017 11:15 AM, Michael "Lee" Lockwood wrote:
Steve Mahler: The RX ctcss tones I'm using are being decoded by the dsp. I get verification of that when running debug in app_rpt.
Neil: I'd like to have the same ctcss tone transmitted for the "repeater tail" and courtesy tone the same amount of time it's set in the rpt.conf file. I think I have mine set to 1.5 seconds.
On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it at cac.net> wrote:
for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone
when would it reset to the 151.4 tone
Thanks
73 Neil Sablatzky K8IT
Allstar Node 41838 KITLINK
Allstar Node 42087 KITLINK HUB
IRLP Node exp0068
Echolink K8IT-L
WIRES-X K8IT 11479 Room 21479
From: Michael "Lee" Lockwood
Sent: Wednesday, August 09, 2017 11:12 AM
To: app_rpt-users at lists.allstarlink.org
Subject: Re: [App_rpt-users] ctcss Encode Issues
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=151.4
rxctcssfreqs=146.2,141.3,151.4
txctcssfreqs=146.2,141.3,151.4
;rxctcssoverride=0
carrierfrom=usb
ctcssfrom=dsp
rxdemod=flat
txprelim=yes
txlimonly=no
txtoctype=phase
txmixa=composite
txmixb=0
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael at lockwood.us.com> wrote:
Hello,
I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0
rxboost=1
txboost=1
rxctcssrelax=1
txctcssdefault=151.4
rxctcssfreqs=146.2,141.3,151.4
txctcssfreqs=146.2,141.3,151.4
;rxctcssoverride=0
carrierfrom=usb
ctcssfrom=dsp
rxdemod=flat
txprelim=yes
txlimonly=no
txtoctype=phase
txmixa=composite
txmixb=0
invertptt=0
duplex=1
rxondelay=0
rxnoisefiltype=0
eeprom=0
--
Michael "Lee" Lockwood
michael at lockwood.us.com
--
Michael "Lee" Lockwood
michael at lockwood.us.com
----------------------------------------------------------------------------
_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
Michael "Lee" Lockwood
michael at lockwood.us.com
Virus-free. www.avg.com
_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--------------------------------------------------------------------------------
_______________________________________________
App_rpt-users mailing list
App_rpt-users at lists.allstarlink.org
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20170809/da387ce6/attachment.html>
More information about the App_rpt-users
mailing list