[App_rpt-users] System seems to connect to other allstar nodes but can't connect to its self.
Bryan St Clair
bryan at k6cbr.us
Fri Aug 31 18:19:23 UTC 2018
Also,
29925 = radio at 127.0.0.1/29925,NONE
40875 = radio at 127.0.0.1/40875,NONE
29925 = radio at 192.168.1.50:4569/29925,NONE
40875 = radio at 192.168.1.50:4569/40875,NONE
I don't think the 2 bottom lines are needed.
If the same server, the 2 top lines would work, but adding the port, if
custom may be required.
Listed here is 4569 but I thought I saw 5469 in your config... and again,
4567 is what I see online currently.
I could be wrong....
On Fri, Aug 31, 2018 at 10:01 AM Loren Tedford <loren at lorentedford.com>
wrote:
> I have been struggling with an issue on this new installation where
> allstar can't connect to a node on its own self..
>
> I can't figure this out no matter what i have tried.. Here is the topology
> of the system. We have a vpn connection that starts on boot so that way we
> have full access to the systems from our local servers.. The reason we vpn
> this is because we go out across Verizon 4G LTE network then come back into
> our servers systems. Here is what ip addr spits out.
>
> root at debian:~# ip addr
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
> default qlen 1
> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> inet 127.0.0.1/8 scope host lo
> valid_lft forever preferred_lft forever
> inet6 ::1/128 scope host
> valid_lft forever preferred_lft forever
> 2: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
> default qlen 1000
> link/ether 04:8d:38:3d:b6:f4 brd ff:ff:ff:ff:ff:ff
> 3: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state UP group default qlen 1000
> link/ether 00:22:4d:7c:5f:94 brd ff:ff:ff:ff:ff:ff
> inet 192.168.1.2/24 brd 192.168.1.255 scope global enp1s0
> valid_lft forever preferred_lft forever
> inet6 2600:1008:b04c:ca22:222:4dff:fe7c:5f94/64 scope global
> mngtmpaddr dynamic
> valid_lft 86382sec preferred_lft 14382sec
> inet6 fe80::222:4dff:fe7c:5f94/64 scope link
> valid_lft forever preferred_lft forever
> 4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc
> pfifo_fast state UNKNOWN group default qlen 100
> link/none
> inet 192.168.8.162 peer 192.168.8.161/32 scope global tun0
> valid_lft forever preferred_lft forever
> inet6 fe80::fe4d:c773:1afa:cead/64 scope link flags 800
> valid_lft forever preferred_lft forever
> root at debian:~#
>
> Here is what iax2 show registry says.
>
> AllStarLink Asterisk Version 1.01 2/13/2018 GIT Version 004b9dd
> Copyright (C) 1999 - 2018 Digium, Inc. Jim Dixon, AllStarLink Inc. and
> others.
> Created by Mark Spencer <markster at digium.com> <markster at digium.com>
> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for
> details.
> This is free software, with components licensed under the GNU General
> Public
> License version 2 and other licenses; you are welcome to redistribute it
> under
> certain conditions. Type 'core show license' for details.
> =========================================================================
> Connected to Asterisk GIT Version 004b9dd currently running on debian (pid
> = 352)
> debian*CLI> iax2 show registry
> Host dnsmgr Username Perceived Refresh
> State
> 44.98.254.145:4569 Y 40875 157.185.79.38:5469 60
> Registered
> 44.98.254.145:4569 Y 29925 157.185.79.38:5469 60
> Registered
> debian*CLI>
>
> Keep in mind for some reason local host doesn't seem to work at all.. And
> it confuses me..
>
> Here is Extensions.conf
>
> root at debian:/etc/asterisk# cat extensions.conf
> [general]
>
> static=yes ; These two lines prevent the command-line interface
> writeprotect=yes ; from overwriting the config file. Leave them here.
>
> [globals]
>
>
> [default]
> exten => i,1,Hangup
>
> [radio-secure]
> exten => 29925,1,rpt,29925
> exten => 40875,1,rpt,40875
>
> [radio-secure-proxy]
> exten => 29925,1,rpt,29925|X
> exten => 40875,1,rpt,40875|X
> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
>
> [pstn-out]
> exten=_NXXNXXXXXX,1,Dial(IAX2/allstar-autopatch/${EXTEN})
> exten=_NXXNXXXXXX,2,Busy
>
> [invalidnum]
> exten=s,1,Wait,3
> exten=s,n,Playback,ss-noservice
> exten=s,n,Wait,1
> exten=s,n,Hangup
>
> [radio]
> exten=_X11,1,Goto(check_route|${EXTEN}|1);
> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
> exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
> exten=00,1,Goto(my-ip|s|1)
>
> [check_route]
> ; no 800
> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
> ; no X00 NPA
> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11 NPA
> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11
> exten=_X11,2,Goto(invalidnum|s|1)
> ; no 555 Prefix in any NPA
> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
> ; no 976 Prefix in any NPA
> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
> ; no NPA=809
> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
> ; no NPA=900
> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
>
> ; okay, route it
> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
> exten=_X.,2,Goto(invalidnum|s|1)
>
> [my-ip]
> exten=s,1,Set(MYADDR=${CURL(http://myip.vg)})
> exten=s,2,Wait,1
> exten=s,3,SayAlpha(${MYADDR})
> exten=s,4,Hangup
>
> [allstar-sys]
>
> exten => 0,1,Answer
> exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => 0,n,Hangup
>
> exten => _0.,1,Answer
> exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => _0.,n,Hangup
>
> exten =>
> _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
> exten => _1.,n,Hangup
>
> exten => _2.,1,Ringing
> exten => _2.,n,Wait(3)
> exten => _2.,n,Answer
> exten => _2.,n,Playback(rpt/node)
> exten => _2.,n,Saydigits(${EXTEN:1})
> exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
> exten => _2.,n,Hangup
>
> exten => _3.,1,Ringing
> exten => _3.,n,Wait(3)
> exten => _3.,n,Answer
> exten => _3.,n,Playback(rpt/node)
> exten => _3.,n,Saydigits(${EXTEN:1})
> exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
> exten => _3.,n,Hangup
>
> exten => _4.,1,Ringing
> exten => _4.,n,Wait(3)
> exten => _4.,n,Answer
> exten => _4.,n,Playback(rpt/node)
> exten => _4.,n,Saydigits(${EXTEN:1})
> exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
> exten => _4.,n,Hangup
>
> exten => _5.,1,Ringing
> exten => _5.,n,Wait(3)
> exten => _5.,n,Answer
> exten => _5.,n,Playback(rpt/node)
> exten => _5.,n,Saydigits(${EXTEN:1})
> exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
> exten => _5.,n,Hangup
>
> [allstar-public]
>
> exten => s,1,Ringing
> exten => s,n,Set(RESP=${CURL(
> https://register.allstarlink.org/cgi-bin/authwebphone.pl?$
> {CALLERID(name)})})
> exten => s,n,Set(NODENUM=${CALLERID(number)})
> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
> exten => s,n,Set(CALLSIGN=${RESP:5})
> exten => s,n,Wait(3)
> exten => s,n,Playback(rpt/node|noanswer)
> exten => s,n,Saydigits(${NODENUM})
> exten => s,n,Set(CALLERID(num)=0)
> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
> exten => s,n,Rpt(${NODENUM}|X)
> exten => s,n,Hangup
> exten => s,n(hangit),Answer
> exten => s,n(hangit),Wait(1)
> exten => s,n(hangit),Hangup
>
> exten => 9999,1,Goto(allstar-public|s|1)
>
> #includeifexists custom/extensions.conf
> [to-callcentric]
> exten => _X.,1,Dial(SIP/${EXTEN}@callcentric)
> root at debian:/etc/asterisk#
> Here is iax.conf
>
> root at debian:/etc/asterisk# cat iax.conf
> [general]
> bindport=5469
> bindaddr=0.0.0.0
> disallow=all
> allow=gsm
> allow=g726aal2
> allow=ulaw
> jitterbuffer=yes
> forcejitterbuffer=yes
> dropcount=2
> maxjitterbuffer=4000
> maxjitterinterps=10
> resyncthreshold=1000
> maxexcessbuffer=80
> minexcessbuffer=10
> jittershrinkrate=1
> autokill=yes
> delayreject=yes
> ;iaxthreadcount=30
> ;iaxmaxthreadcount=150
>
> register=29925:PASSWORD at register.allstarlink.org
> register=40875:PASSWORD at register.allstarlink.org
>
> [allstar-autopatch]
> type=peer
> host=register.allstarlink.org
> username=29925
> secret=592463
> auth=md5
> disallow=all
> allow=gsm
> ;allow=ulaw
> transfer=no
>
>
> [radio-proxy]
> type=user
> deny=0.0.0.0/0.0.0.0
> permit=/255.255.255.255
> context=radio-secure-proxy
> disallow=all
> allow=g726aal2
> transfer=no
>
>
> [radio-proxy-out]
> type=peer
> host=
> username=42447
> secret=800129
> auth=md5
> disallow=all
> allow=g726aal2
> transfer=no
>
>
> ; Incoming radio connections
>
> [radio]
> type=user
> disallow=all
> allow=g726aal2
> allow=gsm
> codecpriority=host
> context=radio-secure
> transfer=no
>
> ; Incoming phone connections to app_rpt
>
> ;[radio-control]
> ;type=user
> ;secret=nunya
> ;disallow=all
> ;allow=gsm
> ;codecpriority=host
> ;context=radio-control
> ;transfer=no
>
> ; Setup for outgoing calls
>
> ;[yourprovider] ; This needs to change
> ;type=peer
> ;host=127.0.0.1
> ;secret=nunya
> ;auth=md5
> ;disallow=all
> ;allow=gsm
> ;transfer=no
>
> [allstar-sys]
> type=user
> context=allstar-sys
> auth=rsa
> inkeys=allstar
> disallow=all
> allow=gsm
> allow=ulaw
>
> [allstar-public]
> type=user
> context=allstar-public
> auth=md5
> secret=allstar
> disallow=all
> allow=gsm
> allow=ulaw
>
> #includeifexists custom/iax.conf
> root at debian:/etc/asterisk#
> Here is what rpt.conf file says.
>
> root at debian:/etc/asterisk# cat rpt.conf
> ; Radio Repeater configuration file (for use with app_rpt)
> ;
> ;
> ; Your Repeater
> ;
> [29925] ; Change this to your assigned
> node number
> rxchannel = SimpleUSB/usb29925
> duplex = 2
> erxgain = -3
> etxgain = 3
> ;controlstates=controlstates
> scheduler = schedule29925
> macro = macro
> startup_macro=*95341715
> morse = morse29925
> macro = macro29925
> functions = functions29925
> phone_functions = functions29925
> link_functions = functions29925
> telemetry = telemetry
> wait_times = wait-times
> context = radio
> callerid = "Repeater" <0000000000>
> idrecording = /etc/asterisk/ids/kc9zhvrpt
> idrecording = |iKC9ZHV
> accountcode = RADIO
> hangtime = 0
> althangtime = 10
> totime = 210000
> idtime = 540000
> politeid = 3000
>
> idtalkover = |iKC9ZHV
> unlinkedct = ct88
> remotect = ct88
> linkunkeyct = ct88
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;nolocallinkct=0
> ;eannmode=1
> ;connpgm=yourconnectprogram
> ;discpgm=yourdisconnectprogram
> ;lnkactenable=0
> ;lnkacttime=1800
> ;lnkactmacro=*52
> ;lnkacttimerwarn=30seconds
> ;remote_inact_timeout=1800
> ;remote_timeout=3600
> nounkeyct = 0
> ;holdofftelem=0
> beaconing = 0
> telemdefault = 2
> ;archivedir=/etc/asterisk/audio
> ;
> ; *** Status Reporting ***
> ;
> ; Uncomment the either group following two statpost lines to report the
> status of your node to stats.allstarlink.org
> ; depending on whether you are running ACID or Limey Linux.
>
> ; ** For ACID ***
>
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ; ** For Limey Linux **
>
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ;
> ; Morse code parameters, these are common to all repeaters.
> ;
>
> [morse29925]
>
> speed=20
> frequency=800
> amplitude=4096
> idfrequency=750
> idamplitude=1024
>
> [schedule29925]
> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>
> [functions29925]
> 1=ilink,1
> 2=ilink,2
> 3=ilink,3
> 4=ilink,4
> 5=macro,1
> 70=ilink,5
> 71=ilink,6
> 72=ilink,7
> 73=ilink,15
> 74=ilink,16
> 75=ilink,8
>
> 951=ilink,11 ; Permanent link disconnect
> ;952=ilink,12 ; Permanent link receive
> 953=ilink,13 ; Permanent link transceive
>
> 80=status,1
> 81=status,2
>
> ;6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> ;0=autopatchdn ; Autopatch down
>
> 6=autopatchup,context=to-callcentric,noct=1,farenddisconnect=1,dialtime=20000
> 0=autopatchdn ; Autopatch down
>
> ;989=cop,4
> 980=status,3
> 99=cop,6
>
> ; Place command macros here
>
> [macro29925]
> ;2= *81
>
>
>
> [40875] ; Change this to your assigned
> node number
>
> rxchannel = SimpleUSB/usb40875
> duplex = 2
> erxgain = -3
> etxgain = 3
> ;controlstates=controlstates
> scheduler = schedule40875
> macro = macro
> startup_macro=*95342448
> morse = morse40875
> macro = macro40875
> functions=functions40875
> phone_functions=functions40875
> link_functions=functions40875
> telemetry=telemetry
> wait_times=wait-times
> context = radio
> callerid = "Repeater" <0000000000>
> idrecording = /etc/asterisk/ids/kc9zhvrpt
> idrecording = |iKC9ZHV/R
> accountcode = RADIO
> hangtime=10
> althangtime=20
> totime=210000
> idtime=540000
> politeid=3000
>
> idtalkover=|iKC9ZHV/R
> unlinkedct=ct89
> remotect=ct89
> linkunkeyct=ct89
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;nolocallinkct=0
> ;eannmode=1
> ;connpgm=yourconnectprogram
> ;discpgm=yourdisconnectprogram
> ;lnkactenable=0
> ;lnkacttime=1800
> ;lnkactmacro=*52
> ;lnkacttimerwarn=30seconds
> ;remote_inact_timeout=1800
> ;remote_timeout=3600
> nounkeyct=0
> ;holdofftelem=0
> beaconing=0
> telemdefault=2
> ;archivedir=/etc/asterisk/audio
> ;
> ; *** Status Reporting ***
> ;
> ; Uncomment the either group following two statpost lines to report the
> status of your node to stats.allstarlink.org
> ; depending on whether you are running ACID or Limey Linux.
>
> ; ** For ACID ***
>
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ; ** For Limey Linux **
>
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>
> ;
> ; Morse code parameters, these are common to all repeaters.
> ;
>
> [morse40875]
>
> speed=20
> frequency=800
> amplitude=4096
> idfrequency=750
> idamplitude=1024
>
> [schedule40875]
> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>
> [functions40875]
> 1=ilink,1
> 2=ilink,2
> 3=ilink,3
> 4=ilink,4
> 5=macro,1
> 70=ilink,5
> 71=ilink,6
> 72=ilink,7
> 73=ilink,15
> 74=ilink,16
> 75=ilink,8
>
>
> 951=ilink,11 ; Permanent link disconnect
> ;952=ilink,12 ; Permanent link receive
> 953=ilink,13 ; Permanent link transceive
>
> 80=status,1
> 81=status,2
>
> 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> 0=autopatchdn ; Autopatch down
>
> ;989=cop,4
> 980=status,3
> 99=cop,6
>
> ; Place command macros here
>
> [macro40875]
>
> ;[telemetry]
> ;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> ;ct2=|t(660,880,150,2048)
> ;ct3=|t(440,0,150,4096)
> ;ct4=|t(550,0,150,2048)
> ;ct5=|t(660,0,150,2048)
> ;ct6=|t(880,0,150,2048)
> ;ct7=|t(660,440,150,2048)
> ;ct8=|t(700,1100,150,2048)
> ;ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;NaSA beep
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;
> ; Nextel tones setup
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;Unknown settings below..
> ;unlinkedct=ct1 ; local off-link tone
> ;remotect=ct3 ; remote base connected tone
> ;linkunkeyct=ct8 ; remote on-link tone
> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> ;remotemon=|t(1209,0,50,2048)
> ;cmdmode=|t(900,903,200,2048)
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;patchup=rpt/callproceeding
> ;patchdown=rpt/callterminated
>
> [telemetry]
> ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> ct2=|t(660,880,150,2048)
> ct3=|t(440,0,150,4096)
> ct4=|t(550,0,150,2048)
> ct5=|t(660,0,150,2048)
> ct6=|t(880,0,150,2048)
> ct7=|t(660,440,150,2048)
> ;ct8=|t(700,1100,150,2048)
> ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;NaSA beep
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;
> ; Nextel tones setup
> remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;Unknown settings below..
> ;unlinkedct=ct1 ; local off-link tone
> ;remotect=ct3 ; remote base connected tone
> ;linkunkeyct=ct8 ; remote on-link tone
> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> ;remotemon=|t(1209,0,50,2048)
> ;cmdmode=|t(900,903,200,2048)
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> patchup=rpt/callproceeding
> patchdown=rpt/callterminated
>
>
> ;
> ; This section allows wait times for telemetry events to be adjusted
> ; A section for wait times can be defined for every repeater
> ;
>
> [wait-times]
> telemwait=2000
> idwait=500
> unkeywait=2000
> calltermwait=2000
>
> ;
> ; This is where you define your nodes which cam be connected to.
> ;
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a definition
> ; for your locak nodes, and private (off of allstar link) nodes here.
>
> 29925 = radio at 127.0.0.1/29925,NONE
> 40875 = radio at 127.0.0.1/40875,NONE
> 29925 = radio at 192.168.1.50:4569/29925,NONE
> 40875 = radio at 192.168.1.50:4569/40875,NONE
>
>
> ; Memories for remote bases
>
> [memory]
>
> ;00 = 146.580,100.0,m
> ;01 = 147.030,103.5,m+t
> ;02 = 147.240,103.5,m+t
> ;03 = 147.765,79.7,m-t
> ;04 = 146.460,100.0,m
> ;05 = 146.550,100.0,m
>
> #includeifexists custom/rpt.conf
> root at debian:/etc/asterisk#
> Above i did try to set at one point in time a static ip and force it to go
> back around however didn't work either..
>
>
> Anythoughts on this??
>
> root at debian:/etc/asterisk# cat /etc/network/interfaces
> # This file describes the network interfaces available on your system
> # and how to activate them. For more information, see interfaces(5).
>
> source /etc/network/interfaces.d/*
>
> # The loopback network interface
> auto lo
> iface lo inet loopback
> iface enp1s0 inet loopback
>
> # The primary network interface
> allow-hotplug enp1s0
> iface enp1s0 inet dhcp
>
> root at debian:/etc/asterisk#
> What did i miss? I even turned firewalls off thinking that might have been
> the issue for not allowing the two nodes to connect together on the same
> system.
>
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
> scroll down to the bottom of the page. Enter your email address and press
> the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
> --
> Bryan
> K6CBR
> bryan at k6cbr.us
> Allstar Base: 43918, 43991
> Allstar Hubs: 43919, 47036, 47061(Testing)
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20180831/706ca260/attachment.html>
More information about the App_rpt-users
mailing list