[App_rpt-users] System seems to connect to other allstar nodes but can't connect to its self.
Loren Tedford
loren at lorentedford.com
Fri Aug 31 18:21:35 UTC 2018
Yeah i think i might have missed that in my configs but I will have a
look we ended up having to take the system offline because it was eating
close to 900mb in 18 hr period of time.. Gotta love running cellular 4g
lte to run your repeaters.. I have gotta find a better solution to the
site then this eventually..
On 8/31/2018 1:19 PM, Bryan St Clair wrote:
> Also,
>
> 29925 = radio at 127.0.0.1/29925,NONE <mailto:radio at 127.0.0.1/29925,NONE>
> 40875 = radio at 127.0.0.1/40875,NONE <mailto:radio at 127.0.0.1/40875,NONE>
> 29925 = radio at 192.168.1.50:4569/29925,NONE
> <mailto:radio at 192.168.1.50:4569/29925,NONE>
> 40875 = radio at 192.168.1.50:4569/40875,NONE
> <mailto:radio at 192.168.1.50:4569/40875,NONE>
>
> I don't think the 2 bottom lines are needed.
>
> If the same server, the 2 top lines would work, but adding the port,
> if custom may be required.
>
> Listed here is 4569 but I thought I saw 5469 in your config... and
> again, 4567 is what I see online currently.
>
> I could be wrong....
>
> On Fri, Aug 31, 2018 at 10:01 AM Loren Tedford <loren at lorentedford.com
> <mailto:loren at lorentedford.com>> wrote:
>
> I have been struggling with an issue on this new installation
> where allstar can't connect to a node on its own self..
>
> I can't figure this out no matter what i have tried.. Here is the
> topology of the system. We have a vpn connection that starts on
> boot so that way we have full access to the systems from our local
> servers.. The reason we vpn this is because we go out across
> Verizon 4G LTE network then come back into our servers systems.
> Here is what ip addr spits out.
>
> root at debian:~# ip addr
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state
> UNKNOWN group default qlen 1
> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> inet 127.0.0.1/8 <http://127.0.0.1/8> scope host lo
> valid_lft forever preferred_lft forever
> inet6 ::1/128 scope host
> valid_lft forever preferred_lft forever
> 2: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
> group default qlen 1000
> link/ether 04:8d:38:3d:b6:f4 brd ff:ff:ff:ff:ff:ff
> 3: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
> pfifo_fast state UP group default qlen 1000
> link/ether 00:22:4d:7c:5f:94 brd ff:ff:ff:ff:ff:ff
> inet 192.168.1.2/24 <http://192.168.1.2/24> brd 192.168.1.255
> scope global enp1s0
> valid_lft forever preferred_lft forever
> inet6 2600:1008:b04c:ca22:222:4dff:fe7c:5f94/64 scope global
> mngtmpaddr dynamic
> valid_lft 86382sec preferred_lft 14382sec
> inet6 fe80::222:4dff:fe7c:5f94/64 scope link
> valid_lft forever preferred_lft forever
> 4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc
> pfifo_fast state UNKNOWN group default qlen 100
> link/none
> inet 192.168.8.162 peer 192.168.8.161/32
> <http://192.168.8.161/32> scope global tun0
> valid_lft forever preferred_lft forever
> inet6 fe80::fe4d:c773:1afa:cead/64 scope link flags 800
> valid_lft forever preferred_lft forever
> root at debian:~#
>
> Here is what iax2 show registry says.
>
> AllStarLink Asterisk Version 1.01 2/13/2018 GIT Version 004b9dd
> Copyright (C) 1999 - 2018 Digium, Inc. Jim Dixon, AllStarLink Inc.
> and others.
> Created by Mark Spencer <markster at digium.com>
> <mailto:markster at digium.com>
> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show
> warranty' for details.
> This is free software, with components licensed under the GNU
> General Public
> License version 2 and other licenses; you are welcome to
> redistribute it under
> certain conditions. Type 'core show license' for details.
> =========================================================================
> Connected to Asterisk GIT Version 004b9dd currently running on
> debian (pid = 352)
> debian*CLI> iax2 show registry
> Host dnsmgr Username Perceived
> Refresh State
> 44.98.254.145:4569 <http://44.98.254.145:4569> Y 40875
> 157.185.79.38:5469 <http://157.185.79.38:5469> 60 Registered
> 44.98.254.145:4569 <http://44.98.254.145:4569> Y 29925
> 157.185.79.38:5469 <http://157.185.79.38:5469> 60 Registered
> debian*CLI>
>
> Keep in mind for some reason local host doesn't seem to work at
> all.. And it confuses me..
>
> Here is Extensions.conf
>
> root at debian:/etc/asterisk# cat extensions.conf
> [general]
>
> static=yes ; These two lines prevent the command-line interface
> writeprotect=yes ; from overwriting the config file. Leave them here.
>
> [globals]
>
>
> [default]
> exten => i,1,Hangup
>
> [radio-secure]
> exten => 29925,1,rpt,29925
> exten => 40875,1,rpt,40875
>
> [radio-secure-proxy]
> exten => 29925,1,rpt,29925|X
> exten => 40875,1,rpt,40875|X
> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
>
> [pstn-out]
> exten=_NXXNXXXXXX,1,Dial(IAX2/allstar-autopatch/${EXTEN})
> exten=_NXXNXXXXXX,2,Busy
>
> [invalidnum]
> exten=s,1,Wait,3
> exten=s,n,Playback,ss-noservice
> exten=s,n,Wait,1
> exten=s,n,Hangup
>
> [radio]
> exten=_X11,1,Goto(check_route|${EXTEN}|1);
> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
> exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
> exten=00,1,Goto(my-ip|s|1)
>
> [check_route]
> ; no 800
> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
> ; no X00 NPA
> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11 NPA
> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11
> exten=_X11,2,Goto(invalidnum|s|1)
> ; no 555 Prefix in any NPA
> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
> ; no 976 Prefix in any NPA
> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
> ; no NPA=809
> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
> ; no NPA=900
> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
>
> ; okay, route it
> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
> exten=_X.,2,Goto(invalidnum|s|1)
>
> [my-ip]
> exten=s,1,Set(MYADDR=${CURL(http://myip.vg)})
> exten=s,2,Wait,1
> exten=s,3,SayAlpha(${MYADDR})
> exten=s,4,Hangup
>
> [allstar-sys]
>
> exten => 0,1,Answer
> exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => 0,n,Hangup
>
> exten => _0.,1,Answer
> exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> https://config.allstarlink.org/config/start.sh >
> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> ${CALLERID(name)})
> exten => _0.,n,Hangup
>
> exten =>
> _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
> exten => _1.,n,Hangup
>
> exten => _2.,1,Ringing
> exten => _2.,n,Wait(3)
> exten => _2.,n,Answer
> exten => _2.,n,Playback(rpt/node)
> exten => _2.,n,Saydigits(${EXTEN:1})
> exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
> exten => _2.,n,Hangup
>
> exten => _3.,1,Ringing
> exten => _3.,n,Wait(3)
> exten => _3.,n,Answer
> exten => _3.,n,Playback(rpt/node)
> exten => _3.,n,Saydigits(${EXTEN:1})
> exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
> exten => _3.,n,Hangup
>
> exten => _4.,1,Ringing
> exten => _4.,n,Wait(3)
> exten => _4.,n,Answer
> exten => _4.,n,Playback(rpt/node)
> exten => _4.,n,Saydigits(${EXTEN:1})
> exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
> exten => _4.,n,Hangup
>
> exten => _5.,1,Ringing
> exten => _5.,n,Wait(3)
> exten => _5.,n,Answer
> exten => _5.,n,Playback(rpt/node)
> exten => _5.,n,Saydigits(${EXTEN:1})
> exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
> exten => _5.,n,Hangup
>
> [allstar-public]
>
> exten => s,1,Ringing
> exten =>
> s,n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)})})
> exten => s,n,Set(NODENUM=${CALLERID(number)})
> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
> exten => s,n,Set(CALLSIGN=${RESP:5})
> exten => s,n,Wait(3)
> exten => s,n,Playback(rpt/node|noanswer)
> exten => s,n,Saydigits(${NODENUM})
> exten => s,n,Set(CALLERID(num)=0)
> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
> exten => s,n,Rpt(${NODENUM}|X)
> exten => s,n,Hangup
> exten => s,n(hangit),Answer
> exten => s,n(hangit),Wait(1)
> exten => s,n(hangit),Hangup
>
> exten => 9999,1,Goto(allstar-public|s|1)
>
> #includeifexists custom/extensions.conf
> [to-callcentric]
> exten => _X.,1,Dial(SIP/${EXTEN}@callcentric)
> root at debian:/etc/asterisk#
> Here is iax.conf
>
> root at debian:/etc/asterisk# cat iax.conf
> [general]
> bindport=5469
> bindaddr=0.0.0.0
> disallow=all
> allow=gsm
> allow=g726aal2
> allow=ulaw
> jitterbuffer=yes
> forcejitterbuffer=yes
> dropcount=2
> maxjitterbuffer=4000
> maxjitterinterps=10
> resyncthreshold=1000
> maxexcessbuffer=80
> minexcessbuffer=10
> jittershrinkrate=1
> autokill=yes
> delayreject=yes
> ;iaxthreadcount=30
> ;iaxmaxthreadcount=150
>
> register=29925:PASSWORD at register.allstarlink.org
> <mailto:register=29925:PASSWORD at register.allstarlink.org>
> register=40875:PASSWORD at register.allstarlink.org
> <mailto:register=40875:PASSWORD at register.allstarlink.org>
>
> [allstar-autopatch]
> type=peer
> host=register.allstarlink.org <http://register.allstarlink.org>
> username=29925
> secret=592463
> auth=md5
> disallow=all
> allow=gsm
> ;allow=ulaw
> transfer=no
>
>
> [radio-proxy]
> type=user
> deny=0.0.0.0/0.0.0.0 <http://0.0.0.0/0.0.0.0>
> permit=/255.255.255.255 <http://255.255.255.255>
> context=radio-secure-proxy
> disallow=all
> allow=g726aal2
> transfer=no
>
>
> [radio-proxy-out]
> type=peer
> host=
> username=42447
> secret=800129
> auth=md5
> disallow=all
> allow=g726aal2
> transfer=no
>
>
> ; Incoming radio connections
>
> [radio]
> type=user
> disallow=all
> allow=g726aal2
> allow=gsm
> codecpriority=host
> context=radio-secure
> transfer=no
>
> ; Incoming phone connections to app_rpt
>
> ;[radio-control]
> ;type=user
> ;secret=nunya
> ;disallow=all
> ;allow=gsm
> ;codecpriority=host
> ;context=radio-control
> ;transfer=no
>
> ; Setup for outgoing calls
>
> ;[yourprovider] ; This needs to change
> ;type=peer
> ;host=127.0.0.1
> ;secret=nunya
> ;auth=md5
> ;disallow=all
> ;allow=gsm
> ;transfer=no
>
> [allstar-sys]
> type=user
> context=allstar-sys
> auth=rsa
> inkeys=allstar
> disallow=all
> allow=gsm
> allow=ulaw
>
> [allstar-public]
> type=user
> context=allstar-public
> auth=md5
> secret=allstar
> disallow=all
> allow=gsm
> allow=ulaw
>
> #includeifexists custom/iax.conf
> root at debian:/etc/asterisk#
> Here is what rpt.conf file says.
>
> root at debian:/etc/asterisk# cat rpt.conf
> ; Radio Repeater configuration file (for use with app_rpt)
> ;
> ;
> ; Your Repeater
> ;
> [29925] ; Change this to your
> assigned node number
> rxchannel = SimpleUSB/usb29925
> duplex = 2
> erxgain = -3
> etxgain = 3
> ;controlstates=controlstates
> scheduler = schedule29925
> macro = macro
> startup_macro=*95341715
> morse = morse29925
> macro = macro29925
> functions = functions29925
> phone_functions = functions29925
> link_functions = functions29925
> telemetry = telemetry
> wait_times = wait-times
> context = radio
> callerid = "Repeater" <0000000000>
> idrecording = /etc/asterisk/ids/kc9zhvrpt
> idrecording = |iKC9ZHV
> accountcode = RADIO
> hangtime = 0
> althangtime = 10
> totime = 210000
> idtime = 540000
> politeid = 3000
>
> idtalkover = |iKC9ZHV
> unlinkedct = ct88
> remotect = ct88
> linkunkeyct = ct88
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;nolocallinkct=0
> ;eannmode=1
> ;connpgm=yourconnectprogram
> ;discpgm=yourdisconnectprogram
> ;lnkactenable=0
> ;lnkacttime=1800
> ;lnkactmacro=*52
> ;lnkacttimerwarn=30seconds
> ;remote_inact_timeout=1800
> ;remote_timeout=3600
> nounkeyct = 0
> ;holdofftelem=0
> beaconing = 0
> telemdefault = 2
> ;archivedir=/etc/asterisk/audio
> ;
> ; *** Status Reporting ***
> ;
> ; Uncomment the either group following two statpost lines to
> report the status of your node to stats.allstarlink.org
> <http://stats.allstarlink.org>
> ; depending on whether you are running ACID or Limey Linux.
>
> ; ** For ACID ***
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
>
> ; ** For Limey Linux **
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
>
> ;
> ; Morse code parameters, these are common to all repeaters.
> ;
>
> [morse29925]
>
> speed=20
> frequency=800
> amplitude=4096
> idfrequency=750
> idamplitude=1024
>
> [schedule29925]
> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>
> [functions29925]
> 1=ilink,1
> 2=ilink,2
> 3=ilink,3
> 4=ilink,4
> 5=macro,1
> 70=ilink,5
> 71=ilink,6
> 72=ilink,7
> 73=ilink,15
> 74=ilink,16
> 75=ilink,8
>
> 951=ilink,11 ; Permanent link disconnect
> ;952=ilink,12 ; Permanent link receive
> 953=ilink,13 ; Permanent link transceive
>
> 80=status,1
> 81=status,2
>
> ;6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> ;0=autopatchdn ; Autopatch down
> 6=autopatchup,context=to-callcentric,noct=1,farenddisconnect=1,dialtime=20000
> 0=autopatchdn ; Autopatch down
>
> ;989=cop,4
> 980=status,3
> 99=cop,6
>
> ; Place command macros here
>
> [macro29925]
> ;2= *81
>
>
>
> [40875] ; Change this to your
> assigned node number
>
> rxchannel = SimpleUSB/usb40875
> duplex = 2
> erxgain = -3
> etxgain = 3
> ;controlstates=controlstates
> scheduler = schedule40875
> macro = macro
> startup_macro=*95342448
> morse = morse40875
> macro = macro40875
> functions=functions40875
> phone_functions=functions40875
> link_functions=functions40875
> telemetry=telemetry
> wait_times=wait-times
> context = radio
> callerid = "Repeater" <0000000000>
> idrecording = /etc/asterisk/ids/kc9zhvrpt
> idrecording = |iKC9ZHV/R
> accountcode = RADIO
> hangtime=10
> althangtime=20
> totime=210000
> idtime=540000
> politeid=3000
>
> idtalkover=|iKC9ZHV/R
> unlinkedct=ct89
> remotect=ct89
> linkunkeyct=ct89
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE
> REMOTE NASA 1
> ;nolocallinkct=0
> ;eannmode=1
> ;connpgm=yourconnectprogram
> ;discpgm=yourdisconnectprogram
> ;lnkactenable=0
> ;lnkacttime=1800
> ;lnkactmacro=*52
> ;lnkacttimerwarn=30seconds
> ;remote_inact_timeout=1800
> ;remote_timeout=3600
> nounkeyct=0
> ;holdofftelem=0
> beaconing=0
> telemdefault=2
> ;archivedir=/etc/asterisk/audio
> ;
> ; *** Status Reporting ***
> ;
> ; Uncomment the either group following two statpost lines to
> report the status of your node to stats.allstarlink.org
> <http://stats.allstarlink.org>
> ; depending on whether you are running ACID or Limey Linux.
>
> ; ** For ACID ***
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
>
> ; ** For Limey Linux **
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
>
> ;
> ; Morse code parameters, these are common to all repeaters.
> ;
>
> [morse40875]
>
> speed=20
> frequency=800
> amplitude=4096
> idfrequency=750
> idamplitude=1024
>
> [schedule40875]
> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>
>
> [functions40875]
> 1=ilink,1
> 2=ilink,2
> 3=ilink,3
> 4=ilink,4
> 5=macro,1
> 70=ilink,5
> 71=ilink,6
> 72=ilink,7
> 73=ilink,15
> 74=ilink,16
> 75=ilink,8
>
>
> 951=ilink,11 ; Permanent link disconnect
> ;952=ilink,12 ; Permanent link receive
> 953=ilink,13 ; Permanent link transceive
>
> 80=status,1
> 81=status,2
>
> 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> 0=autopatchdn ; Autopatch down
>
> ;989=cop,4
> 980=status,3
> 99=cop,6
>
> ; Place command macros here
>
> [macro40875]
>
> ;[telemetry]
> ;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> ;ct2=|t(660,880,150,2048)
> ;ct3=|t(440,0,150,4096)
> ;ct4=|t(550,0,150,2048)
> ;ct5=|t(660,0,150,2048)
> ;ct6=|t(880,0,150,2048)
> ;ct7=|t(660,440,150,2048)
> ;ct8=|t(700,1100,150,2048)
> ;ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;NaSA beep
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE
> REMOTE NASA 1
> ;
> ; Nextel tones setup
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;Unknown settings below..
> ;unlinkedct=ct1 ; local off-link tone
> ;remotect=ct3 ; remote base connected tone
> ;linkunkeyct=ct8 ; remote on-link tone
> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> ;remotemon=|t(1209,0,50,2048)
> ;cmdmode=|t(900,903,200,2048)
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;patchup=rpt/callproceeding
> ;patchdown=rpt/callterminated
>
> [telemetry]
> ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> ct2=|t(660,880,150,2048)
> ct3=|t(440,0,150,4096)
> ct4=|t(550,0,150,2048)
> ct5=|t(660,0,150,2048)
> ct6=|t(880,0,150,2048)
> ct7=|t(660,440,150,2048)
> ;ct8=|t(700,1100,150,2048)
> ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;NaSA beep
> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE
> REMOTE NASA 1
> ;
> ; Nextel tones setup
> remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> ; NEXTEL
> functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> ;Unknown settings below..
> ;unlinkedct=ct1 ; local off-link tone
> ;remotect=ct3 ; remote base connected tone
> ;linkunkeyct=ct8 ; remote on-link tone
> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> ;remotemon=|t(1209,0,50,2048)
> ;cmdmode=|t(900,903,200,2048)
> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> patchup=rpt/callproceeding
> patchdown=rpt/callterminated
>
>
> ;
> ; This section allows wait times for telemetry events to be adjusted
> ; A section for wait times can be defined for every repeater
> ;
>
> [wait-times]
> telemwait=2000
> idwait=500
> unkeywait=2000
> calltermwait=2000
>
> ;
> ; This is where you define your nodes which cam be connected to.
> ;
>
> [nodes]
> ; Note, if you are using automatic update for allstar link nodes,
> ; no allstar link nodes should be defined here. Only place a
> definition
> ; for your locak nodes, and private (off of allstar link) nodes here.
>
> 29925 = radio at 127.0.0.1/29925,NONE <mailto:radio at 127.0.0.1/29925,NONE>
> 40875 = radio at 127.0.0.1/40875,NONE <mailto:radio at 127.0.0.1/40875,NONE>
> 29925 = radio at 192.168.1.50:4569/29925,NONE
> <mailto:radio at 192.168.1.50:4569/29925,NONE>
> 40875 = radio at 192.168.1.50:4569/40875,NONE
> <mailto:radio at 192.168.1.50:4569/40875,NONE>
>
>
> ; Memories for remote bases
>
> [memory]
>
> ;00 = 146.580,100.0,m
> ;01 = 147.030,103.5,m+t
> ;02 = 147.240,103.5,m+t
> ;03 = 147.765,79.7,m-t
> ;04 = 146.460,100.0,m
> ;05 = 146.550,100.0,m
>
> #includeifexists custom/rpt.conf
> root at debian:/etc/asterisk#
> Above i did try to set at one point in time a static ip and force
> it to go back around however didn't work either..
>
>
> Anythoughts on this??
>
> root at debian:/etc/asterisk# cat /etc/network/interfaces
> # This file describes the network interfaces available on your system
> # and how to activate them. For more information, see interfaces(5).
>
> source /etc/network/interfaces.d/*
>
> # The loopback network interface
> auto lo
> iface lo inet loopback
> iface enp1s0 inet loopback
>
> # The primary network interface
> allow-hotplug enp1s0
> iface enp1s0 inet dhcp
>
> root at debian:/etc/asterisk#
> What did i miss? I even turned firewalls off thinking that might
> have been the issue for not allowing the two nodes to connect
> together on the same system.
>
>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> <mailto:App_rpt-users at lists.allstarlink.org>
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> and scroll down to the bottom of the page. Enter your email
> address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a
> message to the list detailing the problem.
>
> --
> Bryan
> K6CBR
> bryan at k6cbr.us <mailto:bryan at k6cbr.us>
> Allstar Base: 43918, 43991
> Allstar Hubs: 43919, 47036, 47061(Testing)
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20180831/ff62750f/attachment.html>
More information about the App_rpt-users
mailing list