[App_rpt-users] System seems to connect to other allstar nodes but can't connect to its self.
Mike
mm at midnighteng.com
Fri Aug 31 18:49:52 UTC 2018
Looking at the difference:
> 40875 = radio at 127.0.0.1/40875,NONE
> 29925 = radio at 192.168.1.50:4569/29925,NONE
Either you need to specify the port on the first two or you need to
change the address to local 127.0.0.1 on the bottom two
I am assuming they are on the same system but if they are not and behind
the same nat, you need additional port routing/definition.
...mike/kb8jnm
On 8/31/2018 2:19 PM, Bryan St Clair wrote:
> Also,
>
> 29925 = radio at 127.0.0.1/29925,NONE
> 40875 = radio at 127.0.0.1/40875,NONE
> 29925 = radio at 192.168.1.50:4569/29925,NONE
> 40875 = radio at 192.168.1.50:4569/40875,NONE
>
> I don't think the 2 bottom lines are needed.
>
> If the same server, the 2 top lines would work, but adding the port, if
> custom may be required.
>
> Listed here is 4569 but I thought I saw 5469 in your config... and again,
> 4567 is what I see online currently.
>
> I could be wrong....
>
> On Fri, Aug 31, 2018 at 10:01 AM Loren Tedford <loren at lorentedford.com>
> wrote:
>
>> I have been struggling with an issue on this new installation where
>> allstar can't connect to a node on its own self..
>>
>> I can't figure this out no matter what i have tried.. Here is the topology
>> of the system. We have a vpn connection that starts on boot so that way we
>> have full access to the systems from our local servers.. The reason we vpn
>> this is because we go out across Verizon 4G LTE network then come back into
>> our servers systems. Here is what ip addr spits out.
>>
>> root at debian:~# ip addr
>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
>> default qlen 1
>> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>> inet 127.0.0.1/8 scope host lo
>> valid_lft forever preferred_lft forever
>> inet6 ::1/128 scope host
>> valid_lft forever preferred_lft forever
>> 2: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
>> default qlen 1000
>> link/ether 04:8d:38:3d:b6:f4 brd ff:ff:ff:ff:ff:ff
>> 3: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
>> state UP group default qlen 1000
>> link/ether 00:22:4d:7c:5f:94 brd ff:ff:ff:ff:ff:ff
>> inet 192.168.1.2/24 brd 192.168.1.255 scope global enp1s0
>> valid_lft forever preferred_lft forever
>> inet6 2600:1008:b04c:ca22:222:4dff:fe7c:5f94/64 scope global
>> mngtmpaddr dynamic
>> valid_lft 86382sec preferred_lft 14382sec
>> inet6 fe80::222:4dff:fe7c:5f94/64 scope link
>> valid_lft forever preferred_lft forever
>> 4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc
>> pfifo_fast state UNKNOWN group default qlen 100
>> link/none
>> inet 192.168.8.162 peer 192.168.8.161/32 scope global tun0
>> valid_lft forever preferred_lft forever
>> inet6 fe80::fe4d:c773:1afa:cead/64 scope link flags 800
>> valid_lft forever preferred_lft forever
>> root at debian:~#
>>
>> Here is what iax2 show registry says.
>>
>> AllStarLink Asterisk Version 1.01 2/13/2018 GIT Version 004b9dd
>> Copyright (C) 1999 - 2018 Digium, Inc. Jim Dixon, AllStarLink Inc. and
>> others.
>> Created by Mark Spencer <markster at digium.com> <markster at digium.com>
>> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for
>> details.
>> This is free software, with components licensed under the GNU General
>> Public
>> License version 2 and other licenses; you are welcome to redistribute it
>> under
>> certain conditions. Type 'core show license' for details.
>> =========================================================================
>> Connected to Asterisk GIT Version 004b9dd currently running on debian (pid
>> = 352)
>> debian*CLI> iax2 show registry
>> Host dnsmgr Username Perceived Refresh
>> State
>> 44.98.254.145:4569 Y 40875 157.185.79.38:5469 60
>> Registered
>> 44.98.254.145:4569 Y 29925 157.185.79.38:5469 60
>> Registered
>> debian*CLI>
>>
>> Keep in mind for some reason local host doesn't seem to work at all.. And
>> it confuses me..
>>
>> Here is Extensions.conf
>>
>> root at debian:/etc/asterisk# cat extensions.conf
>> [general]
>>
>> static=yes ; These two lines prevent the command-line interface
>> writeprotect=yes ; from overwriting the config file. Leave them here.
>>
>> [globals]
>>
>>
>> [default]
>> exten => i,1,Hangup
>>
>> [radio-secure]
>> exten => 29925,1,rpt,29925
>> exten => 40875,1,rpt,40875
>>
>> [radio-secure-proxy]
>> exten => 29925,1,rpt,29925|X
>> exten => 40875,1,rpt,40875|X
>> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
>>
>> [pstn-out]
>> exten=_NXXNXXXXXX,1,Dial(IAX2/allstar-autopatch/${EXTEN})
>> exten=_NXXNXXXXXX,2,Busy
>>
>> [invalidnum]
>> exten=s,1,Wait,3
>> exten=s,n,Playback,ss-noservice
>> exten=s,n,Wait,1
>> exten=s,n,Hangup
>>
>> [radio]
>> exten=_X11,1,Goto(check_route|${EXTEN}|1);
>> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
>> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
>> exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
>> exten=00,1,Goto(my-ip|s|1)
>>
>> [check_route]
>> ; no 800
>> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
>> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
>> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
>> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
>> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
>> ; no X00 NPA
>> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
>> ; no X11 NPA
>> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
>> ; no X11
>> exten=_X11,2,Goto(invalidnum|s|1)
>> ; no 555 Prefix in any NPA
>> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
>> ; no 976 Prefix in any NPA
>> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
>> ; no NPA=809
>> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
>> ; no NPA=900
>> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
>>
>> ; okay, route it
>> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
>> exten=_X.,2,Goto(invalidnum|s|1)
>>
>> [my-ip]
>> exten=s,1,Set(MYADDR=${CURL(http://myip.vg)})
>> exten=s,2,Wait,1
>> exten=s,3,SayAlpha(${MYADDR})
>> exten=s,4,Hangup
>>
>> [allstar-sys]
>>
>> exten => 0,1,Answer
>> exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p
>> /tmp/allstar-config\;curl -sk -m 20 --retry 1
>> https://config.allstarlink.org/config/start.sh >
>> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
>> ${CALLERID(name)})
>> exten => 0,n,Hangup
>>
>> exten => _0.,1,Answer
>> exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p
>> /tmp/allstar-config\;curl -sk -m 20 --retry 1
>> https://config.allstarlink.org/config/start.sh >
>> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
>> ${CALLERID(name)})
>> exten => _0.,n,Hangup
>>
>> exten =>
>> _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
>> exten => _1.,n,Hangup
>>
>> exten => _2.,1,Ringing
>> exten => _2.,n,Wait(3)
>> exten => _2.,n,Answer
>> exten => _2.,n,Playback(rpt/node)
>> exten => _2.,n,Saydigits(${EXTEN:1})
>> exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
>> exten => _2.,n,Hangup
>>
>> exten => _3.,1,Ringing
>> exten => _3.,n,Wait(3)
>> exten => _3.,n,Answer
>> exten => _3.,n,Playback(rpt/node)
>> exten => _3.,n,Saydigits(${EXTEN:1})
>> exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
>> exten => _3.,n,Hangup
>>
>> exten => _4.,1,Ringing
>> exten => _4.,n,Wait(3)
>> exten => _4.,n,Answer
>> exten => _4.,n,Playback(rpt/node)
>> exten => _4.,n,Saydigits(${EXTEN:1})
>> exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
>> exten => _4.,n,Hangup
>>
>> exten => _5.,1,Ringing
>> exten => _5.,n,Wait(3)
>> exten => _5.,n,Answer
>> exten => _5.,n,Playback(rpt/node)
>> exten => _5.,n,Saydigits(${EXTEN:1})
>> exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
>> exten => _5.,n,Hangup
>>
>> [allstar-public]
>>
>> exten => s,1,Ringing
>> exten => s,n,Set(RESP=${CURL(
>> https://register.allstarlink.org/cgi-bin/authwebphone.pl?$
>> {CALLERID(name)})})
>> exten => s,n,Set(NODENUM=${CALLERID(number)})
>> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
>> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
>> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
>> exten => s,n,Set(CALLSIGN=${RESP:5})
>> exten => s,n,Wait(3)
>> exten => s,n,Playback(rpt/node|noanswer)
>> exten => s,n,Saydigits(${NODENUM})
>> exten => s,n,Set(CALLERID(num)=0)
>> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
>> exten => s,n,Rpt(${NODENUM}|X)
>> exten => s,n,Hangup
>> exten => s,n(hangit),Answer
>> exten => s,n(hangit),Wait(1)
>> exten => s,n(hangit),Hangup
>>
>> exten => 9999,1,Goto(allstar-public|s|1)
>>
>> #includeifexists custom/extensions.conf
>> [to-callcentric]
>> exten => _X.,1,Dial(SIP/${EXTEN}@callcentric)
>> root at debian:/etc/asterisk#
>> Here is iax.conf
>>
>> root at debian:/etc/asterisk# cat iax.conf
>> [general]
>> bindport=5469
>> bindaddr=0.0.0.0
>> disallow=all
>> allow=gsm
>> allow=g726aal2
>> allow=ulaw
>> jitterbuffer=yes
>> forcejitterbuffer=yes
>> dropcount=2
>> maxjitterbuffer=4000
>> maxjitterinterps=10
>> resyncthreshold=1000
>> maxexcessbuffer=80
>> minexcessbuffer=10
>> jittershrinkrate=1
>> autokill=yes
>> delayreject=yes
>> ;iaxthreadcount=30
>> ;iaxmaxthreadcount=150
>>
>> register=29925:PASSWORD at register.allstarlink.org
>> register=40875:PASSWORD at register.allstarlink.org
>>
>> [allstar-autopatch]
>> type=peer
>> host=register.allstarlink.org
>> username=29925
>> secret=592463
>> auth=md5
>> disallow=all
>> allow=gsm
>> ;allow=ulaw
>> transfer=no
>>
>>
>> [radio-proxy]
>> type=user
>> deny=0.0.0.0/0.0.0.0
>> permit=/255.255.255.255
>> context=radio-secure-proxy
>> disallow=all
>> allow=g726aal2
>> transfer=no
>>
>>
>> [radio-proxy-out]
>> type=peer
>> host=
>> username=42447
>> secret=800129
>> auth=md5
>> disallow=all
>> allow=g726aal2
>> transfer=no
>>
>>
>> ; Incoming radio connections
>>
>> [radio]
>> type=user
>> disallow=all
>> allow=g726aal2
>> allow=gsm
>> codecpriority=host
>> context=radio-secure
>> transfer=no
>>
>> ; Incoming phone connections to app_rpt
>>
>> ;[radio-control]
>> ;type=user
>> ;secret=nunya
>> ;disallow=all
>> ;allow=gsm
>> ;codecpriority=host
>> ;context=radio-control
>> ;transfer=no
>>
>> ; Setup for outgoing calls
>>
>> ;[yourprovider] ; This needs to change
>> ;type=peer
>> ;host=127.0.0.1
>> ;secret=nunya
>> ;auth=md5
>> ;disallow=all
>> ;allow=gsm
>> ;transfer=no
>>
>> [allstar-sys]
>> type=user
>> context=allstar-sys
>> auth=rsa
>> inkeys=allstar
>> disallow=all
>> allow=gsm
>> allow=ulaw
>>
>> [allstar-public]
>> type=user
>> context=allstar-public
>> auth=md5
>> secret=allstar
>> disallow=all
>> allow=gsm
>> allow=ulaw
>>
>> #includeifexists custom/iax.conf
>> root at debian:/etc/asterisk#
>> Here is what rpt.conf file says.
>>
>> root at debian:/etc/asterisk# cat rpt.conf
>> ; Radio Repeater configuration file (for use with app_rpt)
>> ;
>> ;
>> ; Your Repeater
>> ;
>> [29925] ; Change this to your assigned
>> node number
>> rxchannel = SimpleUSB/usb29925
>> duplex = 2
>> erxgain = -3
>> etxgain = 3
>> ;controlstates=controlstates
>> scheduler = schedule29925
>> macro = macro
>> startup_macro=*95341715
>> morse = morse29925
>> macro = macro29925
>> functions = functions29925
>> phone_functions = functions29925
>> link_functions = functions29925
>> telemetry = telemetry
>> wait_times = wait-times
>> context = radio
>> callerid = "Repeater" <0000000000>
>> idrecording = /etc/asterisk/ids/kc9zhvrpt
>> idrecording = |iKC9ZHV
>> accountcode = RADIO
>> hangtime = 0
>> althangtime = 10
>> totime = 210000
>> idtime = 540000
>> politeid = 3000
>>
>> idtalkover = |iKC9ZHV
>> unlinkedct = ct88
>> remotect = ct88
>> linkunkeyct = ct88
>> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> ;nolocallinkct=0
>> ;eannmode=1
>> ;connpgm=yourconnectprogram
>> ;discpgm=yourdisconnectprogram
>> ;lnkactenable=0
>> ;lnkacttime=1800
>> ;lnkactmacro=*52
>> ;lnkacttimerwarn=30seconds
>> ;remote_inact_timeout=1800
>> ;remote_timeout=3600
>> nounkeyct = 0
>> ;holdofftelem=0
>> beaconing = 0
>> telemdefault = 2
>> ;archivedir=/etc/asterisk/audio
>> ;
>> ; *** Status Reporting ***
>> ;
>> ; Uncomment the either group following two statpost lines to report the
>> status of your node to stats.allstarlink.org
>> ; depending on whether you are running ACID or Limey Linux.
>>
>> ; ** For ACID ***
>>
>> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> ; ** For Limey Linux **
>>
>> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> ;
>> ; Morse code parameters, these are common to all repeaters.
>> ;
>>
>> [morse29925]
>>
>> speed=20
>> frequency=800
>> amplitude=4096
>> idfrequency=750
>> idamplitude=1024
>>
>> [schedule29925]
>> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>>
>>
>> [functions29925]
>> 1=ilink,1
>> 2=ilink,2
>> 3=ilink,3
>> 4=ilink,4
>> 5=macro,1
>> 70=ilink,5
>> 71=ilink,6
>> 72=ilink,7
>> 73=ilink,15
>> 74=ilink,16
>> 75=ilink,8
>>
>> 951=ilink,11 ; Permanent link disconnect
>> ;952=ilink,12 ; Permanent link receive
>> 953=ilink,13 ; Permanent link transceive
>>
>> 80=status,1
>> 81=status,2
>>
>> ;6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
>> ;0=autopatchdn ; Autopatch down
>>
>> 6=autopatchup,context=to-callcentric,noct=1,farenddisconnect=1,dialtime=20000
>> 0=autopatchdn ; Autopatch down
>>
>> ;989=cop,4
>> 980=status,3
>> 99=cop,6
>>
>> ; Place command macros here
>>
>> [macro29925]
>> ;2= *81
>>
>>
>>
>> [40875] ; Change this to your assigned
>> node number
>>
>> rxchannel = SimpleUSB/usb40875
>> duplex = 2
>> erxgain = -3
>> etxgain = 3
>> ;controlstates=controlstates
>> scheduler = schedule40875
>> macro = macro
>> startup_macro=*95342448
>> morse = morse40875
>> macro = macro40875
>> functions=functions40875
>> phone_functions=functions40875
>> link_functions=functions40875
>> telemetry=telemetry
>> wait_times=wait-times
>> context = radio
>> callerid = "Repeater" <0000000000>
>> idrecording = /etc/asterisk/ids/kc9zhvrpt
>> idrecording = |iKC9ZHV/R
>> accountcode = RADIO
>> hangtime=10
>> althangtime=20
>> totime=210000
>> idtime=540000
>> politeid=3000
>>
>> idtalkover=|iKC9ZHV/R
>> unlinkedct=ct89
>> remotect=ct89
>> linkunkeyct=ct89
>> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;nolocallinkct=0
>> ;eannmode=1
>> ;connpgm=yourconnectprogram
>> ;discpgm=yourdisconnectprogram
>> ;lnkactenable=0
>> ;lnkacttime=1800
>> ;lnkactmacro=*52
>> ;lnkacttimerwarn=30seconds
>> ;remote_inact_timeout=1800
>> ;remote_timeout=3600
>> nounkeyct=0
>> ;holdofftelem=0
>> beaconing=0
>> telemdefault=2
>> ;archivedir=/etc/asterisk/audio
>> ;
>> ; *** Status Reporting ***
>> ;
>> ; Uncomment the either group following two statpost lines to report the
>> status of your node to stats.allstarlink.org
>> ; depending on whether you are running ACID or Limey Linux.
>>
>> ; ** For ACID ***
>>
>> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> ; ** For Limey Linux **
>>
>> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
>> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
>>
>> ;
>> ; Morse code parameters, these are common to all repeaters.
>> ;
>>
>> [morse40875]
>>
>> speed=20
>> frequency=800
>> amplitude=4096
>> idfrequency=750
>> idamplitude=1024
>>
>> [schedule40875]
>> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
>>
>>
>> [functions40875]
>> 1=ilink,1
>> 2=ilink,2
>> 3=ilink,3
>> 4=ilink,4
>> 5=macro,1
>> 70=ilink,5
>> 71=ilink,6
>> 72=ilink,7
>> 73=ilink,15
>> 74=ilink,16
>> 75=ilink,8
>>
>>
>> 951=ilink,11 ; Permanent link disconnect
>> ;952=ilink,12 ; Permanent link receive
>> 953=ilink,13 ; Permanent link transceive
>>
>> 80=status,1
>> 81=status,2
>>
>> 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
>> 0=autopatchdn ; Autopatch down
>>
>> ;989=cop,4
>> 980=status,3
>> 99=cop,6
>>
>> ; Place command macros here
>>
>> [macro40875]
>>
>> ;[telemetry]
>> ;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
>> ;ct2=|t(660,880,150,2048)
>> ;ct3=|t(440,0,150,4096)
>> ;ct4=|t(550,0,150,2048)
>> ;ct5=|t(660,0,150,2048)
>> ;ct6=|t(880,0,150,2048)
>> ;ct7=|t(660,440,150,2048)
>> ;ct8=|t(700,1100,150,2048)
>> ;ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;NaSA beep
>> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;
>> ; Nextel tones setup
>> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> ;Unknown settings below..
>> ;unlinkedct=ct1 ; local off-link tone
>> ;remotect=ct3 ; remote base connected tone
>> ;linkunkeyct=ct8 ; remote on-link tone
>> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
>> ;remotemon=|t(1209,0,50,2048)
>> ;cmdmode=|t(900,903,200,2048)
>> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> ;patchup=rpt/callproceeding
>> ;patchdown=rpt/callterminated
>>
>> [telemetry]
>> ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
>> ct2=|t(660,880,150,2048)
>> ct3=|t(440,0,150,4096)
>> ct4=|t(550,0,150,2048)
>> ct5=|t(660,0,150,2048)
>> ct6=|t(880,0,150,2048)
>> ct7=|t(660,440,150,2048)
>> ;ct8=|t(700,1100,150,2048)
>> ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;NaSA beep
>> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
>> ;
>> ; Nextel tones setup
>> remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
>> ; NEXTEL
>> functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> ;Unknown settings below..
>> ;unlinkedct=ct1 ; local off-link tone
>> ;remotect=ct3 ; remote base connected tone
>> ;linkunkeyct=ct8 ; remote on-link tone
>> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
>> ;remotemon=|t(1209,0,50,2048)
>> ;cmdmode=|t(900,903,200,2048)
>> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
>> patchup=rpt/callproceeding
>> patchdown=rpt/callterminated
>>
>>
>> ;
>> ; This section allows wait times for telemetry events to be adjusted
>> ; A section for wait times can be defined for every repeater
>> ;
>>
>> [wait-times]
>> telemwait=2000
>> idwait=500
>> unkeywait=2000
>> calltermwait=2000
>>
>> ;
>> ; This is where you define your nodes which cam be connected to.
>> ;
>>
>> [nodes]
>> ; Note, if you are using automatic update for allstar link nodes,
>> ; no allstar link nodes should be defined here. Only place a definition
>> ; for your locak nodes, and private (off of allstar link) nodes here.
>>
>> 29925 = radio at 127.0.0.1/29925,NONE
>> 40875 = radio at 127.0.0.1/40875,NONE
>> 29925 = radio at 192.168.1.50:4569/29925,NONE
>> 40875 = radio at 192.168.1.50:4569/40875,NONE
>>
>>
>> ; Memories for remote bases
>>
>> [memory]
>>
>> ;00 = 146.580,100.0,m
>> ;01 = 147.030,103.5,m+t
>> ;02 = 147.240,103.5,m+t
>> ;03 = 147.765,79.7,m-t
>> ;04 = 146.460,100.0,m
>> ;05 = 146.550,100.0,m
>>
>> #includeifexists custom/rpt.conf
>> root at debian:/etc/asterisk#
>> Above i did try to set at one point in time a static ip and force it to go
>> back around however didn't work either..
>>
>>
>> Anythoughts on this??
>>
>> root at debian:/etc/asterisk# cat /etc/network/interfaces
>> # This file describes the network interfaces available on your system
>> # and how to activate them. For more information, see interfaces(5).
>>
>> source /etc/network/interfaces.d/*
>>
>> # The loopback network interface
>> auto lo
>> iface lo inet loopback
>> iface enp1s0 inet loopback
>>
>> # The primary network interface
>> allow-hotplug enp1s0
>> iface enp1s0 inet dhcp
>>
>> root at debian:/etc/asterisk#
>> What did i miss? I even turned firewalls off thinking that might have been
>> the issue for not allowing the two nodes to connect together on the same
>> system.
>>
>>
>>
>>
>>
>> _______________________________________________
>> App_rpt-users mailing list
>> App_rpt-users at lists.allstarlink.org
>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>> To unsubscribe from this list please visit
>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
>> scroll down to the bottom of the page. Enter your email address and press
>> the "Unsubscribe or edit options button"
>> You do not need a password to unsubscribe, you can do it via email
>> confirmation. If you have trouble unsubscribing, please send a message to
>> the list detailing the problem.
>>
>> --
>> Bryan
>> K6CBR
>> bryan at k6cbr.us
>> Allstar Base: 43918, 43991
>> Allstar Hubs: 43919, 47036, 47061(Testing)
>>
>>
>
>
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
>
More information about the App_rpt-users
mailing list