[App_rpt-users] System seems to connect to other allstar nodes but can't connect to its self.
Pierre Martel
petem001 at gmail.com
Fri Aug 31 22:58:45 UTC 2018
you have double morse stanza in rpt.conf while it is supposed to be common
for all repeater
you also have macro = macro in both node section while you have 2 stanza
that are [macro29925] and [macro40875] and no stanza that is only [macro]
In iax.conf
you have
bindport = 5469
while you have this as iax2 registery registery
Host dnsmgr Username Perceived Refresh
State
44.98.254.145:4569 Y 40875 157.185.79.38:5469 60
Registered
44.98.254.145:4569 Y 29925 157.185.79.38:5469 60
Registered
debian*CLI>
this is where it does not work in rpt.conf
[nodes]
; Note, if you are using automatic update for allstar link nodes,
; no allstar link nodes should be defined here. Only place a definition
; for your locak nodes, and private (off of allstar link) nodes here.
29925 = radio at 127.0.0.1/29925,NONE
40875 = radio at 127.0.0.1/40875,NONE
29925 = radio at 192.168.1.50:4569/29925,NONE
40875 = radio at 192.168.1.50:4569/40875,NONE
you should have only
29925 = radio at 127.0.0.1:5469/29925,NONE
40875 = radio at 127.0.0.1:5469/40875,NONE
If you put back
bindport = 4569 in iax.conf
you would only need
29925 = radio at 127.0.0.1/29925,NONE
40875 = radio at 127.0.0.1/40875,NONE
hope this help
Le ven. 31 août 2018 à 14:49, Mike <mm at midnighteng.com> a écrit :
> Looking at the difference:
> > 40875 = radio at 127.0.0.1/40875,NONE
> > 29925 = radio at 192.168.1.50:4569/29925,NONE
>
> Either you need to specify the port on the first two or you need to
> change the address to local 127.0.0.1 on the bottom two
>
> I am assuming they are on the same system but if they are not and behind
> the same nat, you need additional port routing/definition.
>
> ...mike/kb8jnm
>
>
> On 8/31/2018 2:19 PM, Bryan St Clair wrote:
> > Also,
> >
> > 29925 = radio at 127.0.0.1/29925,NONE
> > 40875 = radio at 127.0.0.1/40875,NONE
> > 29925 = radio at 192.168.1.50:4569/29925,NONE
> > 40875 = radio at 192.168.1.50:4569/40875,NONE
> >
> > I don't think the 2 bottom lines are needed.
> >
> > If the same server, the 2 top lines would work, but adding the port, if
> > custom may be required.
> >
> > Listed here is 4569 but I thought I saw 5469 in your config... and again,
> > 4567 is what I see online currently.
> >
> > I could be wrong....
> >
> > On Fri, Aug 31, 2018 at 10:01 AM Loren Tedford <loren at lorentedford.com>
> > wrote:
> >
> >> I have been struggling with an issue on this new installation where
> >> allstar can't connect to a node on its own self..
> >>
> >> I can't figure this out no matter what i have tried.. Here is the
> topology
> >> of the system. We have a vpn connection that starts on boot so that way
> we
> >> have full access to the systems from our local servers.. The reason we
> vpn
> >> this is because we go out across Verizon 4G LTE network then come back
> into
> >> our servers systems. Here is what ip addr spits out.
> >>
> >> root at debian:~# ip addr
> >> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
> group
> >> default qlen 1
> >> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> >> inet 127.0.0.1/8 scope host lo
> >> valid_lft forever preferred_lft forever
> >> inet6 ::1/128 scope host
> >> valid_lft forever preferred_lft forever
> >> 2: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
> >> default qlen 1000
> >> link/ether 04:8d:38:3d:b6:f4 brd ff:ff:ff:ff:ff:ff
> >> 3: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> >> state UP group default qlen 1000
> >> link/ether 00:22:4d:7c:5f:94 brd ff:ff:ff:ff:ff:ff
> >> inet 192.168.1.2/24 brd 192.168.1.255 scope global enp1s0
> >> valid_lft forever preferred_lft forever
> >> inet6 2600:1008:b04c:ca22:222:4dff:fe7c:5f94/64 scope global
> >> mngtmpaddr dynamic
> >> valid_lft 86382sec preferred_lft 14382sec
> >> inet6 fe80::222:4dff:fe7c:5f94/64 scope link
> >> valid_lft forever preferred_lft forever
> >> 4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc
> >> pfifo_fast state UNKNOWN group default qlen 100
> >> link/none
> >> inet 192.168.8.162 peer 192.168.8.161/32 scope global tun0
> >> valid_lft forever preferred_lft forever
> >> inet6 fe80::fe4d:c773:1afa:cead/64 scope link flags 800
> >> valid_lft forever preferred_lft forever
> >> root at debian:~#
> >>
> >> Here is what iax2 show registry says.
> >>
> >> AllStarLink Asterisk Version 1.01 2/13/2018 GIT Version 004b9dd
> >> Copyright (C) 1999 - 2018 Digium, Inc. Jim Dixon, AllStarLink Inc. and
> >> others.
> >> Created by Mark Spencer <markster at digium.com> <markster at digium.com>
> >> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty'
> for
> >> details.
> >> This is free software, with components licensed under the GNU General
> >> Public
> >> License version 2 and other licenses; you are welcome to redistribute it
> >> under
> >> certain conditions. Type 'core show license' for details.
> >>
> =========================================================================
> >> Connected to Asterisk GIT Version 004b9dd currently running on debian
> (pid
> >> = 352)
> >> debian*CLI> iax2 show registry
> >> Host dnsmgr Username Perceived Refresh
> >> State
> >> 44.98.254.145:4569 Y 40875 157.185.79.38:5469 60
> >> Registered
> >> 44.98.254.145:4569 Y 29925 157.185.79.38:5469 60
> >> Registered
> >> debian*CLI>
> >>
> >> Keep in mind for some reason local host doesn't seem to work at all..
> And
> >> it confuses me..
> >>
> >> Here is Extensions.conf
> >>
> >> root at debian:/etc/asterisk# cat extensions.conf
> >> [general]
> >>
> >> static=yes ; These two lines prevent the command-line interface
> >> writeprotect=yes ; from overwriting the config file. Leave them here.
> >>
> >> [globals]
> >>
> >>
> >> [default]
> >> exten => i,1,Hangup
> >>
> >> [radio-secure]
> >> exten => 29925,1,rpt,29925
> >> exten => 40875,1,rpt,40875
> >>
> >> [radio-secure-proxy]
> >> exten => 29925,1,rpt,29925|X
> >> exten => 40875,1,rpt,40875|X
> >> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
> >>
> >> [pstn-out]
> >> exten=_NXXNXXXXXX,1,Dial(IAX2/allstar-autopatch/${EXTEN})
> >> exten=_NXXNXXXXXX,2,Busy
> >>
> >> [invalidnum]
> >> exten=s,1,Wait,3
> >> exten=s,n,Playback,ss-noservice
> >> exten=s,n,Wait,1
> >> exten=s,n,Hangup
> >>
> >> [radio]
> >> exten=_X11,1,Goto(check_route|${EXTEN}|1);
> >> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
> >> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
> >> exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1)
> >> exten=00,1,Goto(my-ip|s|1)
> >>
> >> [check_route]
> >> ; no 800
> >> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
> >> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
> >> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
> >> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
> >> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
> >> ; no X00 NPA
> >> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
> >> ; no X11 NPA
> >> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
> >> ; no X11
> >> exten=_X11,2,Goto(invalidnum|s|1)
> >> ; no 555 Prefix in any NPA
> >> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
> >> ; no 976 Prefix in any NPA
> >> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
> >> ; no NPA=809
> >> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
> >> ; no NPA=900
> >> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
> >>
> >> ; okay, route it
> >> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
> >> exten=_X.,2,Goto(invalidnum|s|1)
> >>
> >> [my-ip]
> >> exten=s,1,Set(MYADDR=${CURL(http://myip.vg)})
> >> exten=s,2,Wait,1
> >> exten=s,3,SayAlpha(${MYADDR})
> >> exten=s,4,Hangup
> >>
> >> [allstar-sys]
> >>
> >> exten => 0,1,Answer
> >> exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> >> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> >> https://config.allstarlink.org/config/start.sh >
> >> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> >> ${CALLERID(name)})
> >> exten => 0,n,Hangup
> >>
> >> exten => _0.,1,Answer
> >> exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p
> >> /tmp/allstar-config\;curl -sk -m 20 --retry 1
> >> https://config.allstarlink.org/config/start.sh >
> >> /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh
> >> ${CALLERID(name)})
> >> exten => _0.,n,Hangup
> >>
> >> exten =>
> >> _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120)
> >> exten => _1.,n,Hangup
> >>
> >> exten => _2.,1,Ringing
> >> exten => _2.,n,Wait(3)
> >> exten => _2.,n,Answer
> >> exten => _2.,n,Playback(rpt/node)
> >> exten => _2.,n,Saydigits(${EXTEN:1})
> >> exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
> >> exten => _2.,n,Hangup
> >>
> >> exten => _3.,1,Ringing
> >> exten => _3.,n,Wait(3)
> >> exten => _3.,n,Answer
> >> exten => _3.,n,Playback(rpt/node)
> >> exten => _3.,n,Saydigits(${EXTEN:1})
> >> exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P)
> >> exten => _3.,n,Hangup
> >>
> >> exten => _4.,1,Ringing
> >> exten => _4.,n,Wait(3)
> >> exten => _4.,n,Answer
> >> exten => _4.,n,Playback(rpt/node)
> >> exten => _4.,n,Saydigits(${EXTEN:1})
> >> exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P)
> >> exten => _4.,n,Hangup
> >>
> >> exten => _5.,1,Ringing
> >> exten => _5.,n,Wait(3)
> >> exten => _5.,n,Answer
> >> exten => _5.,n,Playback(rpt/node)
> >> exten => _5.,n,Saydigits(${EXTEN:1})
> >> exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P)
> >> exten => _5.,n,Hangup
> >>
> >> [allstar-public]
> >>
> >> exten => s,1,Ringing
> >> exten => s,n,Set(RESP=${CURL(
> >> https://register.allstarlink.org/cgi-bin/authwebphone.pl?$
> >> {CALLERID(name)})})
> >> exten => s,n,Set(NODENUM=${CALLERID(number)})
> >> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
> >> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
> >> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
> >> exten => s,n,Set(CALLSIGN=${RESP:5})
> >> exten => s,n,Wait(3)
> >> exten => s,n,Playback(rpt/node|noanswer)
> >> exten => s,n,Saydigits(${NODENUM})
> >> exten => s,n,Set(CALLERID(num)=0)
> >> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
> >> exten => s,n,Rpt(${NODENUM}|X)
> >> exten => s,n,Hangup
> >> exten => s,n(hangit),Answer
> >> exten => s,n(hangit),Wait(1)
> >> exten => s,n(hangit),Hangup
> >>
> >> exten => 9999,1,Goto(allstar-public|s|1)
> >>
> >> #includeifexists custom/extensions.conf
> >> [to-callcentric]
> >> exten => _X.,1,Dial(SIP/${EXTEN}@callcentric)
> >> root at debian:/etc/asterisk#
> >> Here is iax.conf
> >>
> >> root at debian:/etc/asterisk# cat iax.conf
> >> [general]
> >> bindport=5469
> >> bindaddr=0.0.0.0
> >> disallow=all
> >> allow=gsm
> >> allow=g726aal2
> >> allow=ulaw
> >> jitterbuffer=yes
> >> forcejitterbuffer=yes
> >> dropcount=2
> >> maxjitterbuffer=4000
> >> maxjitterinterps=10
> >> resyncthreshold=1000
> >> maxexcessbuffer=80
> >> minexcessbuffer=10
> >> jittershrinkrate=1
> >> autokill=yes
> >> delayreject=yes
> >> ;iaxthreadcount=30
> >> ;iaxmaxthreadcount=150
> >>
> >> register=29925:PASSWORD at register.allstarlink.org
> >> register=40875:PASSWORD at register.allstarlink.org
> >>
> >> [allstar-autopatch]
> >> type=peer
> >> host=register.allstarlink.org
> >> username=29925
> >> secret=592463
> >> auth=md5
> >> disallow=all
> >> allow=gsm
> >> ;allow=ulaw
> >> transfer=no
> >>
> >>
> >> [radio-proxy]
> >> type=user
> >> deny=0.0.0.0/0.0.0.0
> >> permit=/255.255.255.255
> >> context=radio-secure-proxy
> >> disallow=all
> >> allow=g726aal2
> >> transfer=no
> >>
> >>
> >> [radio-proxy-out]
> >> type=peer
> >> host=
> >> username=42447
> >> secret=800129
> >> auth=md5
> >> disallow=all
> >> allow=g726aal2
> >> transfer=no
> >>
> >>
> >> ; Incoming radio connections
> >>
> >> [radio]
> >> type=user
> >> disallow=all
> >> allow=g726aal2
> >> allow=gsm
> >> codecpriority=host
> >> context=radio-secure
> >> transfer=no
> >>
> >> ; Incoming phone connections to app_rpt
> >>
> >> ;[radio-control]
> >> ;type=user
> >> ;secret=nunya
> >> ;disallow=all
> >> ;allow=gsm
> >> ;codecpriority=host
> >> ;context=radio-control
> >> ;transfer=no
> >>
> >> ; Setup for outgoing calls
> >>
> >> ;[yourprovider] ; This needs to change
> >> ;type=peer
> >> ;host=127.0.0.1
> >> ;secret=nunya
> >> ;auth=md5
> >> ;disallow=all
> >> ;allow=gsm
> >> ;transfer=no
> >>
> >> [allstar-sys]
> >> type=user
> >> context=allstar-sys
> >> auth=rsa
> >> inkeys=allstar
> >> disallow=all
> >> allow=gsm
> >> allow=ulaw
> >>
> >> [allstar-public]
> >> type=user
> >> context=allstar-public
> >> auth=md5
> >> secret=allstar
> >> disallow=all
> >> allow=gsm
> >> allow=ulaw
> >>
> >> #includeifexists custom/iax.conf
> >> root at debian:/etc/asterisk#
> >> Here is what rpt.conf file says.
> >>
> >> root at debian:/etc/asterisk# cat rpt.conf
> >> ; Radio Repeater configuration file (for use with app_rpt)
> >> ;
> >> ;
> >> ; Your Repeater
> >> ;
> >> [29925] ; Change this to your assigned
> >> node number
> >> rxchannel = SimpleUSB/usb29925
> >> duplex = 2
> >> erxgain = -3
> >> etxgain = 3
> >> ;controlstates=controlstates
> >> scheduler = schedule29925
> >> macro = macro
> >> startup_macro=*95341715
> >> morse = morse29925
> >> macro = macro29925
> >> functions = functions29925
> >> phone_functions = functions29925
> >> link_functions = functions29925
> >> telemetry = telemetry
> >> wait_times = wait-times
> >> context = radio
> >> callerid = "Repeater" <0000000000>
> >> idrecording = /etc/asterisk/ids/kc9zhvrpt
> >> idrecording = |iKC9ZHV
> >> accountcode = RADIO
> >> hangtime = 0
> >> althangtime = 10
> >> totime = 210000
> >> idtime = 540000
> >> politeid = 3000
> >>
> >> idtalkover = |iKC9ZHV
> >> unlinkedct = ct88
> >> remotect = ct88
> >> linkunkeyct = ct88
> >>
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >> ;nolocallinkct=0
> >> ;eannmode=1
> >> ;connpgm=yourconnectprogram
> >> ;discpgm=yourdisconnectprogram
> >> ;lnkactenable=0
> >> ;lnkacttime=1800
> >> ;lnkactmacro=*52
> >> ;lnkacttimerwarn=30seconds
> >> ;remote_inact_timeout=1800
> >> ;remote_timeout=3600
> >> nounkeyct = 0
> >> ;holdofftelem=0
> >> beaconing = 0
> >> telemdefault = 2
> >> ;archivedir=/etc/asterisk/audio
> >> ;
> >> ; *** Status Reporting ***
> >> ;
> >> ; Uncomment the either group following two statpost lines to report the
> >> status of your node to stats.allstarlink.org
> >> ; depending on whether you are running ACID or Limey Linux.
> >>
> >> ; ** For ACID ***
> >>
> >>
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> >> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
> >>
> >> ; ** For Limey Linux **
> >>
> >>
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> >> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
> >>
> >> ;
> >> ; Morse code parameters, these are common to all repeaters.
> >> ;
> >>
> >> [morse29925]
> >>
> >> speed=20
> >> frequency=800
> >> amplitude=4096
> >> idfrequency=750
> >> idamplitude=1024
> >>
> >> [schedule29925]
> >> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
> >>
> >>
> >> [functions29925]
> >> 1=ilink,1
> >> 2=ilink,2
> >> 3=ilink,3
> >> 4=ilink,4
> >> 5=macro,1
> >> 70=ilink,5
> >> 71=ilink,6
> >> 72=ilink,7
> >> 73=ilink,15
> >> 74=ilink,16
> >> 75=ilink,8
> >>
> >> 951=ilink,11 ; Permanent link disconnect
> >> ;952=ilink,12 ; Permanent link receive
> >> 953=ilink,13 ; Permanent link transceive
> >>
> >> 80=status,1
> >> 81=status,2
> >>
> >> ;6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> >> ;0=autopatchdn ; Autopatch down
> >>
> >>
> 6=autopatchup,context=to-callcentric,noct=1,farenddisconnect=1,dialtime=20000
> >> 0=autopatchdn ; Autopatch down
> >>
> >> ;989=cop,4
> >> 980=status,3
> >> 99=cop,6
> >>
> >> ; Place command macros here
> >>
> >> [macro29925]
> >> ;2= *81
> >>
> >>
> >>
> >> [40875] ; Change this to your assigned
> >> node number
> >>
> >> rxchannel = SimpleUSB/usb40875
> >> duplex = 2
> >> erxgain = -3
> >> etxgain = 3
> >> ;controlstates=controlstates
> >> scheduler = schedule40875
> >> macro = macro
> >> startup_macro=*95342448
> >> morse = morse40875
> >> macro = macro40875
> >> functions=functions40875
> >> phone_functions=functions40875
> >> link_functions=functions40875
> >> telemetry=telemetry
> >> wait_times=wait-times
> >> context = radio
> >> callerid = "Repeater" <0000000000>
> >> idrecording = /etc/asterisk/ids/kc9zhvrpt
> >> idrecording = |iKC9ZHV/R
> >> accountcode = RADIO
> >> hangtime=10
> >> althangtime=20
> >> totime=210000
> >> idtime=540000
> >> politeid=3000
> >>
> >> idtalkover=|iKC9ZHV/R
> >> unlinkedct=ct89
> >> remotect=ct89
> >> linkunkeyct=ct89
> >> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE
> NASA 1
> >> ;nolocallinkct=0
> >> ;eannmode=1
> >> ;connpgm=yourconnectprogram
> >> ;discpgm=yourdisconnectprogram
> >> ;lnkactenable=0
> >> ;lnkacttime=1800
> >> ;lnkactmacro=*52
> >> ;lnkacttimerwarn=30seconds
> >> ;remote_inact_timeout=1800
> >> ;remote_timeout=3600
> >> nounkeyct=0
> >> ;holdofftelem=0
> >> beaconing=0
> >> telemdefault=2
> >> ;archivedir=/etc/asterisk/audio
> >> ;
> >> ; *** Status Reporting ***
> >> ;
> >> ; Uncomment the either group following two statpost lines to report the
> >> status of your node to stats.allstarlink.org
> >> ; depending on whether you are running ACID or Limey Linux.
> >>
> >> ; ** For ACID ***
> >>
> >>
> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> >> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates
> >>
> >> ; ** For Limey Linux **
> >>
> >>
> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null
> >> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status
> updates
> >>
> >> ;
> >> ; Morse code parameters, these are common to all repeaters.
> >> ;
> >>
> >> [morse40875]
> >>
> >> speed=20
> >> frequency=800
> >> amplitude=4096
> >> idfrequency=750
> >> idamplitude=1024
> >>
> >> [schedule40875]
> >> ;dtmf_function = m h dom mon dow ; ala cron, star is implied
> >>
> >>
> >> [functions40875]
> >> 1=ilink,1
> >> 2=ilink,2
> >> 3=ilink,3
> >> 4=ilink,4
> >> 5=macro,1
> >> 70=ilink,5
> >> 71=ilink,6
> >> 72=ilink,7
> >> 73=ilink,15
> >> 74=ilink,16
> >> 75=ilink,8
> >>
> >>
> >> 951=ilink,11 ; Permanent link disconnect
> >> ;952=ilink,12 ; Permanent link receive
> >> 953=ilink,13 ; Permanent link transceive
> >>
> >> 80=status,1
> >> 81=status,2
> >>
> >> 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
> >> 0=autopatchdn ; Autopatch down
> >>
> >> ;989=cop,4
> >> 980=status,3
> >> 99=cop,6
> >>
> >> ; Place command macros here
> >>
> >> [macro40875]
> >>
> >> ;[telemetry]
> >> ;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> >> ;ct2=|t(660,880,150,2048)
> >> ;ct3=|t(440,0,150,4096)
> >> ;ct4=|t(550,0,150,2048)
> >> ;ct5=|t(660,0,150,2048)
> >> ;ct6=|t(880,0,150,2048)
> >> ;ct7=|t(660,440,150,2048)
> >> ;ct8=|t(700,1100,150,2048)
> >>
> ;ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;NaSA beep
> >> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE
> NASA 1
> >> ;
> >> ; Nextel tones setup
> >>
> ;remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> ;remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> ;cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >> ;Unknown settings below..
> >> ;unlinkedct=ct1 ; local off-link tone
> >> ;remotect=ct3 ; remote base connected tone
> >> ;linkunkeyct=ct8 ; remote on-link tone
> >> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> >> ;remotemon=|t(1209,0,50,2048)
> >> ;cmdmode=|t(900,903,200,2048)
> >> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >> ;patchup=rpt/callproceeding
> >> ;patchdown=rpt/callterminated
> >>
> >> [telemetry]
> >> ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
> >> ct2=|t(660,880,150,2048)
> >> ct3=|t(440,0,150,4096)
> >> ct4=|t(550,0,150,2048)
> >> ct5=|t(660,0,150,2048)
> >> ct6=|t(880,0,150,2048)
> >> ct7=|t(660,440,150,2048)
> >> ;ct8=|t(700,1100,150,2048)
> >>
> ct88=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >> ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;NaSA beep
> >> ;ct89=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;remotetx=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;remotemon=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;cmdmode=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE NASA 1
> >> ;functcomplete=|t(2175,0,200,2048)(1950,0,175,2048) ; TONE REMOTE
> NASA 1
> >> ;
> >> ; Nextel tones setup
> >>
> remotetx=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> remotemon=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >>
> cmdmode=|t(1760,0,30,1048)(0,0,30,0)(1760,0,30,2048)(0,0,30,0)(1760,0,30,2048)
> >> ; NEXTEL
> >> functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >> ;Unknown settings below..
> >> ;unlinkedct=ct1 ; local off-link tone
> >> ;remotect=ct3 ; remote base connected tone
> >> ;linkunkeyct=ct8 ; remote on-link tone
> >> ;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
> >> ;remotemon=|t(1209,0,50,2048)
> >> ;cmdmode=|t(900,903,200,2048)
> >> ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
> >> patchup=rpt/callproceeding
> >> patchdown=rpt/callterminated
> >>
> >>
> >> ;
> >> ; This section allows wait times for telemetry events to be adjusted
> >> ; A section for wait times can be defined for every repeater
> >> ;
> >>
> >> [wait-times]
> >> telemwait=2000
> >> idwait=500
> >> unkeywait=2000
> >> calltermwait=2000
> >>
> >> ;
> >> ; This is where you define your nodes which cam be connected to.
> >> ;
> >>
> >> [nodes]
> >> ; Note, if you are using automatic update for allstar link nodes,
> >> ; no allstar link nodes should be defined here. Only place a definition
> >> ; for your locak nodes, and private (off of allstar link) nodes here.
> >>
> >> 29925 = radio at 127.0.0.1/29925,NONE
> >> 40875 = radio at 127.0.0.1/40875,NONE
> >> 29925 = radio at 192.168.1.50:4569/29925,NONE
> >> 40875 = radio at 192.168.1.50:4569/40875,NONE
> >>
> >>
> >> ; Memories for remote bases
> >>
> >> [memory]
> >>
> >> ;00 = 146.580,100.0,m
> >> ;01 = 147.030,103.5,m+t
> >> ;02 = 147.240,103.5,m+t
> >> ;03 = 147.765,79.7,m-t
> >> ;04 = 146.460,100.0,m
> >> ;05 = 146.550,100.0,m
> >>
> >> #includeifexists custom/rpt.conf
> >> root at debian:/etc/asterisk#
> >> Above i did try to set at one point in time a static ip and force it to
> go
> >> back around however didn't work either..
> >>
> >>
> >> Anythoughts on this??
> >>
> >> root at debian:/etc/asterisk# cat /etc/network/interfaces
> >> # This file describes the network interfaces available on your system
> >> # and how to activate them. For more information, see interfaces(5).
> >>
> >> source /etc/network/interfaces.d/*
> >>
> >> # The loopback network interface
> >> auto lo
> >> iface lo inet loopback
> >> iface enp1s0 inet loopback
> >>
> >> # The primary network interface
> >> allow-hotplug enp1s0
> >> iface enp1s0 inet dhcp
> >>
> >> root at debian:/etc/asterisk#
> >> What did i miss? I even turned firewalls off thinking that might have
> been
> >> the issue for not allowing the two nodes to connect together on the same
> >> system.
> >>
> >>
> >>
> >>
> >>
> >> _______________________________________________
> >> App_rpt-users mailing list
> >> App_rpt-users at lists.allstarlink.org
> >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> >>
> >> To unsubscribe from this list please visit
> >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
> >> scroll down to the bottom of the page. Enter your email address and
> press
> >> the "Unsubscribe or edit options button"
> >> You do not need a password to unsubscribe, you can do it via email
> >> confirmation. If you have trouble unsubscribing, please send a message
> to
> >> the list detailing the problem.
> >>
> >> --
> >> Bryan
> >> K6CBR
> >> bryan at k6cbr.us
> >> Allstar Base: 43918, 43991
> >> Allstar Hubs: 43919, 47036, 47061(Testing)
> >>
> >>
> >
> >
> >
> > _______________________________________________
> > App_rpt-users mailing list
> > App_rpt-users at lists.allstarlink.org
> > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
> >
> > To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
> scroll down to the bottom of the page. Enter your email address and press
> the "Unsubscribe or edit options button"
> > You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
> >
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and
> scroll down to the bottom of the page. Enter your email address and press
> the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20180831/16734c32/attachment.html>
More information about the App_rpt-users
mailing list