[App_rpt-users] Icom FR 5000 repeater - URI - Alllstarlink node

[Mike]

David,

First I will say I am not familiar with either device you are using,

So take all of this with a grain of salt.

I doubt you can take AF OUT and make a COR detect from it without extra 
hardware as a VOX circuit etc.

To me, from your connection diagram, It looks like you need to do one of 
a few things.

If you can get a valid PL from the radio and use that for your COR line. 
(use hard PL for COR)

OR

Use PL (as detected in apt_rpt) for COR - 'carrierfrom=dsp'


Someone is likely to have a better answer but those are my thoughts.

Perhaps share a link to the uri makers site for your device for details 
on that I could take a better look.


...mike,kb8jnm


On 12/8/2018 5:50 AM, Lardizabal David D. wrote:
> Hi
>
> My name is David Lardizabal HQ2DDL.  I am trying to install and 
> AllstarLink node with a repeater Icom FR 5000 and I am trying to 
> figure out the pinout / setting on repeater.  If anyone has done this 
> setup would appreciate the help.
>
> I have all ready have done some testing but I am getting a lot of 
> noice, like the squelch is open and transmitting to connected node, ( 
> I am able to connect to other nodes via line command, I have not been 
> able to get the DTMF tones to work to connect/disconnect to nodes.)
>
> My current pin out is like this:
>
>
> FR 5000 RepeaterDML URI
>
> 7GND =================> 20GND
> 8MOD IN   =================> 22TX AUDIO
> 9DISC OUT ================> 21RX AUDIO
> 14GND =================> 19GND
> 19PTT=================>  1PTT
> 22AF OUT  =================>  8COR DET   (?)
>
> *** as a Note: I found out in a pin out for RTCM with an ICOM FR6000 
> repeater;
>
> I recently connected a Micro-Node RTCM to an ICOM FR6000 UHF repeater.
> The FR5000/6000 has a DB25 auxiliary connector on the rear.
> Here is the sable pin-out I used. Maybe this helps someone else.
>
> FR6000                                     RTCM
> ----------------------------------------------------------------------
> Pin 11 - 12VDC Out ------------------ Pin 1 +V In
> Pin 8 - MOD IN ------------------------- Pin 2 TX Audio
> Pin 9 Discriminator ------------------- Pin 3 RX Audio
> Pin 21 Analog Audible Out -------- Pin 4 CTCSS In
> Pin 14 GND------------------------------ Pin 5 GND
> Pin 19 EPTT ---------------------------- Pin 7 PTT
> DB25 Shell --- soldered to braid---DB9 Shell
>
> Programming FR6000.
> Configured for CTCSS on Receive, no CTCSS on transmit.
> Program Pin 21 I/O for Audible Out which is a signal indication when the
> receiver is unmuted by squelch/tone.
> Program Pin 19 I/O for EPTT - External PTT
>
> 73
>
> David
>
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20181208/5258a315/attachment.html>