Re: [Allstar Digital] ambe_audio.py and bridge.py
I was able to resolve the problem in /opt/dmrlink/ambe_audio/dmrlink.cfg I had to create a peer pointing back the master I have configured in /opt/dmrlink/bridge/dmrlink.cfg I had to put the IP 192.168.X.X in the IP field using 0.0.0.0 or 127.0.0.1 would not allow things to work. Everything seems fine. I was talking to a ham on analog he said the audio was a little hot. I noticed in the DMRGateway.ini there is a agc gain adjustment. Is this a OK adjustment to bring the audio down a bit? I also noticed that if I key too quickly after someone is done talking on analog my transmission on DMR will not go out. I found waiting a few seconds, works fine. Would this have something to do with a hang time setting? Other than that I can not find any other issues. Thanks Bob/N1XBM On Sat, Jan 30, 2016 at 3:53 PM, Steve Zingman <szingman@msgstor.com> wrote:
Use netstat,to troubleshoot
Sent via smoke signal (AT&T 4G LTE)
-------- Original message -------- From: Robert Newberry <N1XBM@amsat.org> Date: 01/30/2016 3:45 PM (GMT-05:00) To: Steve Zingman <szingman@msgstor.com> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
Did you want to see what comes up with I type netstat? While I have bridge.py or ambe_audio.py?
On Sat, Jan 30, 2016 at 3:35 PM, Steve Zingman <szingman@msgstor.com> wrote:
netstat
Sent via smoke signal (AT&T 4G LTE)
-------- Original message -------- From: Robert Newberry <N1XBM@amsat.org> Date: 01/30/2016 3:33 PM (GMT-05:00) To: Digital linking using Asterisk and app_rpt < allstar-digital@lists.keekles.org> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
Well I thought I could instead in /opt/dmrlink/ambe_audio/dmrlink.cfg set it up to peer to my master I established in /opt/dmrlink/bridge/dmrlink.cfg
That doesn't work either. I obviously have to do something different.
On Sat, Jan 30, 2016 at 1:53 PM, Robert Newberry <N1XBM@amsat.org> wrote:
So I am working on getting everything to run at boot. I've been adding one process at a time to rc.local. So far so good, when I tried to add ambe_audio.py I got this error.
raise error.CannotListenError(self.interface, self.port, le) twisted.internet.error.CannotListenError: Couldn't listen on 0.0.0.0:50001: [Errno 98] Address already in use.
So my repeater is a peer to dmrlink in /opt/dmrlink/bridge/dmrlinkcfg. I also set the same thing up in /opt/dmrlink/ambe_audio/dmrlink.cfg
This obviously does not work, so can anyone straighten me out?
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Robert Congrats on your install. Why don't you write up an email detailing what you did, what you learned and let others benefit from your experiences. Mike On Saturday, January 30, 2016, Robert Newberry <N1XBM@amsat.org> wrote:
I was able to resolve the problem in /opt/dmrlink/ambe_audio/dmrlink.cfg I had to create a peer pointing back the master I have configured in /opt/dmrlink/bridge/dmrlink.cfg
I had to put the IP 192.168.X.X in the IP field using 0.0.0.0 or 127.0.0.1 would not allow things to work. Everything seems fine.
I was talking to a ham on analog he said the audio was a little hot. I noticed in the DMRGateway.ini there is a agc gain adjustment. Is this a OK adjustment to bring the audio down a bit?
I also noticed that if I key too quickly after someone is done talking on analog my transmission on DMR will not go out. I found waiting a few seconds, works fine. Would this have something to do with a hang time setting?
Other than that I can not find any other issues.
Thanks Bob/N1XBM
On Sat, Jan 30, 2016 at 3:53 PM, Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Use netstat,to troubleshoot
Sent via smoke signal (AT&T 4G LTE)
-------- Original message -------- From: Robert Newberry <N1XBM@amsat.org <javascript:_e(%7B%7D,'cvml','N1XBM@amsat.org');>> Date: 01/30/2016 3:45 PM (GMT-05:00) To: Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
Did you want to see what comes up with I type netstat? While I have bridge.py or ambe_audio.py?
On Sat, Jan 30, 2016 at 3:35 PM, Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
netstat
Sent via smoke signal (AT&T 4G LTE)
-------- Original message -------- From: Robert Newberry <N1XBM@amsat.org <javascript:_e(%7B%7D,'cvml','N1XBM@amsat.org');>> Date: 01/30/2016 3:33 PM (GMT-05:00) To: Digital linking using Asterisk and app_rpt < allstar-digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','allstar-digital@lists.keekles.org');>> Subject: Re: [Allstar Digital] ambe_audio.py and bridge.py
Well I thought I could instead in /opt/dmrlink/ambe_audio/dmrlink.cfg set it up to peer to my master I established in /opt/dmrlink/bridge/dmrlink.cfg
That doesn't work either. I obviously have to do something different.
On Sat, Jan 30, 2016 at 1:53 PM, Robert Newberry <N1XBM@amsat.org <javascript:_e(%7B%7D,'cvml','N1XBM@amsat.org');>> wrote:
So I am working on getting everything to run at boot. I've been adding one process at a time to rc.local. So far so good, when I tried to add ambe_audio.py I got this error.
raise error.CannotListenError(self.interface, self.port, le) twisted.internet.error.CannotListenError: Couldn't listen on 0.0.0.0:50001: [Errno 98] Address already in use.
So my repeater is a peer to dmrlink in /opt/dmrlink/bridge/dmrlinkcfg. I also set the same thing up in /opt/dmrlink/ambe_audio/dmrlink.cfg
This obviously does not work, so can anyone straighten me out?
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
participants (2)
-
Mike Zingman -
Robert Newberry