So I followed instructions from previous emails. I first went to my rpt.conf and did this rxchannel = usrp/127.0.0.1:34001:32001 Then Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter. Is there any other ports I need to set? It looks like most things are set default.
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct? On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
I am not sure if my AMBEserverGPIO is running or not. Could I do ps ax | grep AMBEserverGPIO to check? I ran dmrlink.py under /opt/dmrlink/ambe_audio and test looked ok with my repeater peered to it. I did check if DMRGateway by doing ps ax | grep DMRGateway and saw it was running. I did not check the DMRGateway.ini so it must of been default to whatever came with it. Also when running python ambe_audio.py under /opt/dmrlink/ambe_audio I did not see any errors, when I key my HT I could see it on the console out put. I didn't see any grievous errors. Also did not hear myself on my node. Thank you, Bob/N1XBM On Fri, Jan 29, 2016 at 5:43 AM, Steve Zingman <szingman@msgstor.com> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct. I confirmed that AMBEserverGPIO is running. As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt. In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway. N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658 On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
set dmrlink.cfg to INFO and output to console start ambe_audio.py in the foreground. Talk on repeater What do you get on the screen? copy and paste it to message. On 01/29/2016 09:32 PM, Robert Newberry wrote:
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
I confirmed that AMBEserverGPIO is running.
As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py
If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt.
In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway.
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658
On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
root@repeater:/opt/dmrlink/ambe_audio# python ambe_audio.py INFO DMRlink 'ambe_audio.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM STARTING... INFO (N1XBM_MASTER) IPSC Instance Created: 54321, 0.0.0.0:50001 DMRLink ambe server Send UDP frames to DMR gateway 127.0.0.1:1234 Remote control is listening on: repeater 1235 INFO (N1XBM_MASTER) Master Registration Packet Received from peer 312307, 192.168.0.202:50002 Voice Transmission Start on TS 2 and TG Local (2) from N1XBM Voice Transmission End 5.22 seconds On Fri, Jan 29, 2016 at 9:36 PM, Steve Zingman <szingman@msgstor.com> wrote:
set dmrlink.cfg to INFO and output to console start ambe_audio.py in the foreground. Talk on repeater What do you get on the screen? copy and paste it to message.
On 01/29/2016 09:32 PM, Robert Newberry wrote:
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
I confirmed that AMBEserverGPIO is running.
As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py
If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt.
In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway.
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658
On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
usrp channel driver enabled in modules.conf? On 01/29/2016 09:41 PM, Robert Newberry wrote:
root@repeater:/opt/dmrlink/ambe_audio# python ambe_audio.py INFO DMRlink 'ambe_audio.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM STARTING... INFO (N1XBM_MASTER) IPSC Instance Created: 54321, 0.0.0.0:50001 <http://0.0.0.0:50001> DMRLink ambe server Send UDP frames to DMR gateway 127.0.0.1:1234 <http://127.0.0.1:1234> Remote control is listening on: repeater 1235 INFO (N1XBM_MASTER) Master Registration Packet Received from peer 312307, 192.168.0.202:50002 <http://192.168.0.202:50002> Voice Transmission Start on TS 2 and TG Local (2) from N1XBM Voice Transmission End 5.22 seconds
On Fri, Jan 29, 2016 at 9:36 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
set dmrlink.cfg to INFO and output to console start ambe_audio.py in the foreground. Talk on repeater What do you get on the screen? copy and paste it to message.
On 01/29/2016 09:32 PM, Robert Newberry wrote:
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
I confirmed that AMBEserverGPIO is running.
As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py
If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt.
In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway.
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658
On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
Yes under /etc/asterisk modules.conf I have load => chan_usrp.so I noticed under /etc/asterisk there sisnt a chan_usrp.conf is there supposed to be one? I noticted there is a simpleusb.conf. Maybe its nothing I just noticed it. On Fri, Jan 29, 2016 at 9:44 PM, Steve Zingman <szingman@msgstor.com> wrote:
usrp channel driver enabled in modules.conf?
On 01/29/2016 09:41 PM, Robert Newberry wrote:
root@repeater:/opt/dmrlink/ambe_audio# python ambe_audio.py INFO DMRlink 'ambe_audio.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM STARTING... INFO (N1XBM_MASTER) IPSC Instance Created: 54321, 0.0.0.0:50001 DMRLink ambe server Send UDP frames to DMR gateway 127.0.0.1:1234 Remote control is listening on: repeater 1235 INFO (N1XBM_MASTER) Master Registration Packet Received from peer 312307, 192.168.0.202:50002 Voice Transmission Start on TS 2 and TG Local (2) from N1XBM Voice Transmission End 5.22 seconds
On Fri, Jan 29, 2016 at 9:36 PM, Steve Zingman <szingman@msgstor.com> wrote:
set dmrlink.cfg to INFO and output to console start ambe_audio.py in the foreground. Talk on repeater What do you get on the screen? copy and paste it to message.
On 01/29/2016 09:32 PM, Robert Newberry wrote:
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
I confirmed that AMBEserverGPIO is running.
As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py
If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt.
In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway.
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658
On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
There is no config file for chan_usrp On 01/29/2016 09:49 PM, Robert Newberry wrote:
Yes under /etc/asterisk modules.conf I have load => chan_usrp.so
I noticed under /etc/asterisk there sisnt a chan_usrp.conf is there supposed to be one? I noticted there is a simpleusb.conf. Maybe its nothing I just noticed it.
On Fri, Jan 29, 2016 at 9:44 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
usrp channel driver enabled in modules.conf?
On 01/29/2016 09:41 PM, Robert Newberry wrote:
root@repeater:/opt/dmrlink/ambe_audio# python ambe_audio.py INFO DMRlink 'ambe_audio.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM STARTING... INFO (N1XBM_MASTER) IPSC Instance Created: 54321, 0.0.0.0:50001 <http://0.0.0.0:50001> DMRLink ambe server Send UDP frames to DMR gateway 127.0.0.1:1234 <http://127.0.0.1:1234> Remote control is listening on: repeater 1235 INFO (N1XBM_MASTER) Master Registration Packet Received from peer 312307, 192.168.0.202:50002 <http://192.168.0.202:50002> Voice Transmission Start on TS 2 and TG Local (2) from N1XBM Voice Transmission End 5.22 seconds
On Fri, Jan 29, 2016 at 9:36 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
set dmrlink.cfg to INFO and output to console start ambe_audio.py in the foreground. Talk on repeater What do you get on the screen? copy and paste it to message.
On 01/29/2016 09:32 PM, Robert Newberry wrote:
So I looked a DMRGateway.ini under /etc. The ports match what I see in DMRGateway.pdf. All of the IPs are 127.0.0.1 which I believe is correct.
I confirmed that AMBEserverGPIO is running.
As far as I know to test this I go to /opt/dmrlink/ambe_audio then type python ambe_audio.py
If Everything is right, I should hear myself in my node. I am connected to my node using iaxrpt.
In ambe_audio.cfg what is the remote control port? Default is 1235 the gateway port is 1234 which I think is the port between dmrlink and dmrgateway.
N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658
On Jan 29, 2016 5:43 AM, "Steve Zingman" <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is AMBEserverGPIO running? Have you tested it for proper operation? is DMRGateway running? Are the settings in DMRGateway.ini correct?
On 01/28/2016 10:16 PM, Robert Newberry wrote:
So I followed instructions from previous emails.
I first went to my rpt.conf and did this
rxchannel = usrp/127.0.0.1:34001:32001
Then
Configure dmrlink.cfg in /opt/dmrlink/ambe_audio as a master Configure the repeater to point at the Pi as a peer. cd /opt/dmrlink/ambe_audio Test it by running python dmrlink.py in ambe_audio Watch the log stop dmrlink.py If you have rebooted DMRGateway should be running. Check it with ps ax | grep DMRGateway If not start it with /usr/local/bin/DMRGateway & Make sure asterisk is running and connect a node to it so you can hear it. start python ambe_audio.py
Everything looks OK on the output, other than not hearing myself. I am also using TS2 TG2 which by the looks of the default ambe_audio.cfg in /opt/dmrlink/ambe_audio has TG2 in the filter.
Is there any other ports I need to set? It looks like most things are set default.
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused. On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Create a simple master on the same system. Just like you have now in the ambe_audio directory. Now change you existing dmrlink.cfg to point at it. point your repeater at it. repeater <----> master <----> ambe_audio On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
OK I get that I need to point my repeater at the master and then point ambe_audio to the master. Where I am confused is can I do this in /opt/dmrlink/ambe_audio basically create a peer and a master in the same file. I'll take a look at that last e-mail you sent from nwdigital. On Fri, Jan 29, 2016 at 10:11 PM, Steve Zingman <szingman@msgstor.com> wrote:
Create a simple master on the same system. Just like you have now in the ambe_audio directory. Now change you existing dmrlink.cfg to point at it. point your repeater at it.
repeater <----> master <----> ambe_audio
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Verify what is listening via UDP on the machine netstat -unap See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
You may also want to show us your dmrgateway output. It shows the connection status to the dv3000. On Friday, January 29, 2016, Steve Zingman <szingman@msgstor.com> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');> szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 0.0.0.0:* 276/asterisk On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
I don't see DMRGateway running On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 <http://127.0.0.1:32001> 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 <http://0.0.0.0:2460> 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 <http://0.0.0.0:4569> 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
I might be misunderstanding this but I did this which I thought meant it was running. root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~# On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Nope, It means you grep was running. root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 <http://127.0.0.1:32001> 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 <http://0.0.0.0:2460> 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 <http://0.0.0.0:4569> 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
OK group I got it running by checking an old thread. I found /usr/local/bin/DMRGateway & I did this and now I can hear myself. I'm unsure if I'll have to do this every time I assume there is a way to make it run at boot. On Fri, Jan 29, 2016 at 10:27 PM, Steve Zingman <szingman@msgstor.com> wrote:
Nope, It means you grep was running.
root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR
On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list <Allstar-Digital@lists.keekles.org>Allstar-Digital@lists.keekles.org <http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Yes, you can have it run at boot. Google is your friend. On Friday, January 29, 2016, Robert Newberry <N1XBM@amsat.org> wrote:
OK group I got it running by checking an old thread. I found /usr/local/bin/DMRGateway & I did this and now I can hear myself. I'm unsure if I'll have to do this every time I assume there is a way to make it run at boot.
On Fri, Jan 29, 2016 at 10:27 PM, Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Nope, It means you grep was running.
root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR
On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman < <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');> szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman < <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');> szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');> szingman@msgstor.com <javascript:_e(%7B%7D,'cvml','szingman@msgstor.com');>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
> rxchannel = usrp/127.0.0.1:34001:32001 >
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> <http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');>http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <javascript:_e(%7B%7D,'cvml','Allstar-Digital@lists.keekles.org');> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Yes it needs to be running, so does AMBEserverGPIO and ambe_audio.py On 01/29/2016 10:34 PM, Robert Newberry wrote:
OK group I got it running by checking an old thread. I found /usr/local/bin/DMRGateway & I did this and now I can hear myself. I'm unsure if I'll have to do this every time I assume there is a way to make it run at boot.
On Fri, Jan 29, 2016 at 10:27 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Nope, It means you grep was running.
root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR
On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 <http://127.0.0.1:32001> 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 <http://0.0.0.0:2460> 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 <http://0.0.0.0:4569> 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
OK guys I should be able to hopefully figure that out with some proper application of swearing and some Canadian club. So for this whole shooting match to work as a bridge and a gateway at the same time. bridge.py and ambe_audio.py has to be running at the same time in the background. I think I've done something similar like this when setting up my media server. Thanks for sticking by me. On Fri, Jan 29, 2016 at 10:37 PM, Steve Zingman <szingman@msgstor.com> wrote:
Yes it needs to be running, so does AMBEserverGPIO and ambe_audio.py
On 01/29/2016 10:34 PM, Robert Newberry wrote:
OK group I got it running by checking an old thread. I found /usr/local/bin/DMRGateway & I did this and now I can hear myself. I'm unsure if I'll have to do this every time I assume there is a way to make it run at boot.
On Fri, Jan 29, 2016 at 10:27 PM, Steve Zingman <szingman@msgstor.com> wrote:
Nope, It means you grep was running.
root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR
On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman < <szingman@msgstor.com> szingman@msgstor.com> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman < <szingman@msgstor.com>szingman@msgstor.com> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
> rxchannel = usrp/127.0.0.1:34001:32001 >
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list <Allstar-Digital@lists.keekles.org>Allstar-Digital@lists.keekles.org <http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list <Allstar-Digital@lists.keekles.org>Allstar-Digital@lists.keekles.org <http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing listAllstar-Digital@lists.keekles.orghttp://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
Yes, That is why the /opt/dmrlink directory structure was built. Each directory has what it needs to run a separate instance of dmrlink. On 01/29/2016 10:42 PM, Robert Newberry wrote:
OK guys I should be able to hopefully figure that out with some proper application of swearing and some Canadian club.
So for this whole shooting match to work as a bridge and a gateway at the same time. bridge.py and ambe_audio.py has to be running at the same time in the background. I think I've done something similar like this when setting up my media server.
Thanks for sticking by me.
On Fri, Jan 29, 2016 at 10:37 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Yes it needs to be running, so does AMBEserverGPIO and ambe_audio.py
On 01/29/2016 10:34 PM, Robert Newberry wrote:
OK group I got it running by checking an old thread. I found /usr/local/bin/DMRGateway & I did this and now I can hear myself. I'm unsure if I'll have to do this every time I assume there is a way to make it run at boot.
On Fri, Jan 29, 2016 at 10:27 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Nope, It means you grep was running.
root@repeater:~# ps ax | grep DMR 6423 ? Sl 0:03 ./DMRGateway 7069 pts/1 S+ 0:00 grep DMR
On 01/29/2016 10:25 PM, Robert Newberry wrote:
I might be misunderstanding this but I did this which I thought meant it was running.
root@repeater:~# ps ax | grep DMRGateway 761 pts/0 S+ 0:00 grep DMRGateway root@repeater:~#
On Fri, Jan 29, 2016 at 10:22 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
I don't see DMRGateway running
On 01/29/2016 10:21 PM, Robert Newberry wrote:
root@repeater:~# netstat -unap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name udp 0 0 127.0.0.1:32001 <http://127.0.0.1:32001> 0.0.0.0:* 276/asterisk udp 0 0 0.0.0.0:2460 <http://0.0.0.0:2460> 0.0.0.0:* 221/AMBEserverGPIO udp 0 0 0.0.0.0:4569 <http://0.0.0.0:4569> 0.0.0.0:* 276/asterisk
On Fri, Jan 29, 2016 at 10:14 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Verify what is listening via UDP on the machine netstat -unap
See this page for testing your AMBEserverGPIO <http://nwdigitalradio.com/dv3000-ambeserver> <http://nwdigitalradio.com/dv3000-ambeserver>
On 01/29/2016 10:05 PM, Robert Newberry wrote:
OK sorry, just need to clarify. Currently under /opt/dmrlink/ambe_audio/dmrlink.cfg my repeater is currently a peer to dmrlink. So should I also create a peer in that same file? Sorry I'm a little confused.
On Fri, Jan 29, 2016 at 9:57 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Build a master, point your repeater at it. change ambe_audio from a master to a peer. point it at the new master
On 01/29/2016 09:55 PM, Robert Newberry wrote:
I just went back and reconfirmed it. 42657 is the only node I have defined in rpt.conf
On Fri, Jan 29, 2016 at 9:52 PM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Is rxchannel = usrp/127.0.0.1:34001:32001 the only rxchannel defined in rpt.conf?
On 01/29/2016 09:49 PM, Robert Newberry wrote:
rxchannel = usrp/127.0.0.1:34001:32001
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org <mailto:Allstar-Digital@lists.keekles.org> http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
_______________________________________________ Allstar-Digital mailing list Allstar-Digital@lists.keekles.org http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital
-- "Anything is possible if you don't know what you are talking about." 1st Law of Logic
participants (3)
-
Mike Zingman -
Robert Newberry -
Steve Zingman